harvst S14 Manuale utente
Setup guide
Model S14
Greenhouse only, Solar, 3-season and 4-season versions
Visit www.harvst.co.uk/setup for more information, videos and photos
Parts / assembly diagram
Thank you for buying a Harvst greenhouse.
If you have any questions while setting up, send us an email
(help@harvst.co.uk) or have a look at our forums at
https://grow.harvst.co.uk
There are also videos at
https://www.harvst.co.uk/setup
Parts list (aluminium pieces)
Weʼve fitted the front and rear uprights to the side base parts for you, to save
time and help you get started. Weʼve also pre-fitted screws into bars, where
required.
440mm x3
2 lid sides, with plastic corners
1 lid centre
1210mm x1
Front upper crossbar
(box profile as alternative)
450mm x4
Side panel crossbar
728mm x2
Front upright
(fitted to assembly)
910mm x2
Rear upright
(fitted to assembly)
1250mm x1
Lid front
550mm x1
Lid prop
1210mm Shelf support
x4 GH / Solar models
x8 4-season model
450mm x2
Side base parts
(fitted to assembly)
1210mm x2
Front and rear base parts
Front with double channel up
Rear with single channel up
Side panel top assembly x2
One le and one right
Ridge assembly (with hinge) x1
Fixings and small parts
4.5 x 30 screw x4
Button head
M5 x 8mm x8
Cap head
M5 x 8mm x16
M5 nut x11
M5 Nylock x1
M5 washer x2
M5 x 40mm x3
M5 square nut x18
Blanking plug x8
20cm cable tie x2
14cm tie x100
Fixing bracket x2
Automatic lid lier fixings
(Solar, 3-season and 4-season models only)
Lier arm plate x1
Mounting plate x1
M5 x 8mm x4
M5 square nut x2
M5 nut x2
M4 x 12mm x2
M4 nut x2
Panels
Tools provided
3mm allen key, 4mm allen key
8mm spanner
Pozidrive screwdriver
Tools required
Tape measure to check parts
Secateurs for cutting pipe
You will also have mesh shelves, the quantity
depending on which model you have bought.
Slotting parts together
The greenhouse is based on parts that slot together using 30mm stainless steel screws, as shown
in the diagram below.
Ensure that your screwdriver is
fully engaged with the screw
head when you tighten, so that
you donʼt round off the head of
the screw.
Note the orientation of each
piece in the description;
specifically the closed face.
WARNING Every care has been taken during manufacture to avoid sharp edges or burrs,
however you should still take care when handling metal parts.
Step 1 - Seal the polycarbonate panels (optional)
Twin wall polycarbonate panels act like double glazing for your mini greenhouse, and to improve
the insulation characteristics, it is good to seal the ends of the channels using the provided foil
tape. It also helps prevent bugs from crawling into the plastic.
This step is optional - it can take some time but is recommended.
1. Peel back a couple of inches of the protective foil which covers both sides of the panels,
but donʼt take it all the way off yet.
2. Apply the tape to the end of the panel, covering the flutes.
3. Fold down the sides to seal the tape to the panels.
The white film is on the UV protected side which should face out when you place the panels into
the greenhouse.
Step 2 - Attach the door handles
Do this step first to allow the adhesive tape to cure while you assemble the rest of the
greenhouse. Youʼll fit the doors at the end.
Parts
2 x door handle
2 x polycarbonate door
Fix the door handles to the doors as shown in the drawing
above, using the tape fixed to the handles.
Make sure you have peeled the protective film off the doors
first, the surfaces are clean, dry and free from grease, and that
the UV treated side of the door panels (white film) faces out.
There is a sticker on the right door.
Step 3 - Fit weather seal
Parts
1 x self adhesive weather strip
Fix the weather strips to the inside of the right hand door,
as shown on the drawing above.
Step 4 - Assemble the base
Parts:
1 x le assembly
1 x right assembly
1 x front base 121cm
1 x rear base 121cm
This step is best done
on a flat surface where
you can easily access
the screws at the
bottom, such as a
table or workbench.
The le and right
assemblies are
interchangeable.
The rear base part has
the single channel
facing up, and the front
has the double
channel facing up.
Slot the le and right assemblies over the
screws on the front and rear base parts and
tighten the screws.
Step 5 - Insert square nuts to side cross bars
Parts
4 x side cross bar 45cm
10 x square nut
Insert three square nuts into the inside channel of
each cross bar that will go on the le side of the
greenhouse.
Two will be for the shelves, and the third will be for
supporting the irrigation pipe (itʼs worth fitting the
nuts now even if you donʼt have the irrigation kit yet).
The inside channel is the one opposite the closed
face.
Insert two square nuts into the inside channel of the
right hand cross bars.
Step 6 - Insert the side panels and side cross bars
The top side panel on the le has a hole with a grommet in it for an external hose or tank
connection, if you have a solar, 3-season or 4-season model.
Parts:
4 x clear side panel
4 x side cross bar 45cm
Peel the protective plastic off both
sides of two side panels, remembering
which side had the white film.
The side with the white film should
face outside; it is the UV treated
side.
Slot the panels into the frame, then
slide the bars, closed face outwards,
down over the clear side panel.
Tighten the screws. Repeat for the
other side.
Finish inserting all the side panels and
cross bars in the same way.
Altri manuali per S14
2
Indice
Altri manuali harvst Kit serra
harvst
harvst Sprout S10 Mini Manuale utente
harvst
harvst S24 Manuale utente
harvst
harvst Yard Manuale utente
harvst
harvst S24 Manuale utente
harvst
harvst S14 Manuale utente
harvst
harvst Sprout S10 Mini Manuale utente
harvst
harvst WaterMate Manuale utente
harvst
harvst Terrace Manuale utente
harvst
harvst Sprout S10 Mini Manuale utente
harvst
harvst S14 Manuale utente
