harvst S24 Manuale utente
Setup guide
Model S24
Greenhouse only, Solar, 3-season and 4-season versions
V2 / From Jan 2022
4-season model shown above
Exploded diagram
Visit www.harvst.co.uk/setup for more information, videos and photos
Thank you for buying a Harvst greenhouse.
If you have any questions while setting up, send us an email
(help@harvst.co.uk) or have a look at our forums at
https://grow.harvst.co.uk
There are also videos at https://www.harvst.co.uk/setup
Important information
Sprout mini greenhouses are intended for outdoor garden use, fixed securely to a fence, wall or
the ground. Use outdoors unsecured, or indoors, is at your own risk.
Mains powered greenhouses are provided with a waterproof power supply and 5m of mains
cable. They should be plugged into a waterproof outdoor socket, or an indoor socket in a shed,
garage or other safe place. Non waterproof extension leads should never be used.
Parts list (aluminium pieces)
Weʼve fitted the front and rear uprights to the side base parts for you, to save
time and help you get started. Weʼve also pre-fitted screws into bars, where
required.
450mm x3
2 lid sides with corner cubes
1 lid centre
1210mm x1
Front upper crossbar
(box profile as alternative)
450mm x8
Side panel crossbar
1285mm x2
Front upright
(fitted to assembly)
910mm x2
Rear upright
(fitted to assembly)
1210mm x1
Lid front
535mm x1
Lid prop
1210mm Shelf support
x4 GH / Solar models
x8 4-season model
Rear have holes in middle
450mm x2
Side base parts
(fitted to assembly)
1210mm x2
Front and rear base parts
Front: double channel up
Rear: single channel up
1250mm x1
Lid rear
1250mm x1
Ridge
With black PVC channel
Side panel top assembly x2
One le and one right
Fixings and small parts
Additional fixings will be supplied if your greenhouse comes with a smart control system. See
the control system setup guide for details.
M5 square nut x32
M5 washer x4
M5 nut x11
M5 Nylock x1
M5 x 8 button x22
M5 x 10 button x6
M5 x 16 button x1
M5 x 8 cap x8
M4 x 12mm x2
May be slot head
M5 x 30mm x3
M5 x 40mm x3
Shelf bracket x4
Joining strap x2
Fixing bracket x2
Lier arm plate
Lier adapter plate
Cable tie x12
Hole punch
M4 nut x2
Blanking plug x15
4mm tube for fixing
shelves
80mm x4, 120mm x2
4.5 x 30mm screw x4
O-ring x2
Roll of foil tape
Panels
Tools provided
3mm allen key, 4mm allen key
8mm spanner
Pozidrive screwdriver
Tools required (not supplied)
Tape measure to check parts
Secateurs for cutting pipe
You will also have mesh shelves, the quantity
depending on which model you have bought.
Slotting parts together
The greenhouse is based on parts that slot together using 30mm stainless steel screws, as shown
in the diagram below.
Ensure that your screwdriver is
fully engaged with the screw
head when you tighten, so that
you donʼt round off the head of
the screw.
Note the orientation of each
piece in the description;
specifically the closed face.
WARNING Every care has been taken during manufacture to avoid sharp edges or burrs,
however you should still take care when handling metal parts.
WARNING DO NOT USE POWER TOOLS TO SCREW IN THE SCREWS. YOU MIGHT SNAP OFF
THE HEAD, WHICH IS NOT COVERED BY WARRANTY.
Step 1 - Seal the polycarbonate panels (optional)
Twin wall polycarbonate panels act like double glazing for your mini greenhouse, and to improve
the insulation characteristics, it is good to seal the ends of the channels using the provided foil
tape. It also helps prevent bugs from crawling into the plastic.
This step is optional - it can take some time but is recommended.
1. Peel back a couple of inches of the protective foil which covers both sides of the panels,
but donʼt take it all the way off yet.
2. Apply the tape to the end of the panel, covering the flutes.
3. Fold down the sides to seal the tape to the panels.
The white film is on the UV protected side which should face out when you place the panels into
the greenhouse.
Step 2 - Assemble the base
Parts:
1 x le assembly
1 x right assembly
1 x front base 121cm
1 x rear base 121cm
This step is best done
on a flat surface where
you can easily access
the screws at the
bottom, such as a
table or workbench.
The le and right
assemblies are
interchangeable.
The rear base part has
the single channel
facing up, and the front
has the double
channel facing up.
Slot the le and right assemblies over the
screws on the front and rear base parts and
tighten the screws.
Step 3 - Fit the rear upright joining straps
Move the frame down onto the floor.
Parts
2 x joining strap
8 x M5 x 8 button head
8 x M5 square nut
2 x top rear upright 56cm
Insert the 8mm bolts into the joining straps, and put a
square nut on the back of each, loosely.
Slide the square nuts into the outside channel of the
rear uprights.
The outside channel is the far le or far right channel;
the joining straps will be on the outside of the
greenhouse.
Tighten the lower pair of bolts.
Step 4 - Fit the top rear uprights
Parts
2 x top rear upright 56cm
With the holes as shown in the drawing below, slide the top rear
uprights down over the joining straps.
The closed face should be to the rear of the greenhouse.
Tighten the upper pair of bolts.
Altri manuali per S24
2
Indice
Altri manuali harvst Kit serra
harvst
harvst S14 Manuale utente
harvst
harvst Sprout S6 Mini Manuale utente
harvst
harvst Sprout S10 Mini Manuale utente
harvst
harvst WaterMate Manuale utente
harvst
harvst Terrace Manuale utente
harvst
harvst Sprout S10 Mini Manuale utente
harvst
harvst Sprout S10 Mini Manuale utente
harvst
harvst Sprout S6 Mini Manuale utente
harvst
harvst Sprout S6 Mini Manuale utente
harvst
harvst S24 Manuale utente
