HBM PACEline CMD Series Manuale utente
Operating Manual | Bedienungsanleitung |
Manuel d'emploi |
English Deutsch Français
CMD
Hottinger Baldwin Messtechnik GmbH
Im Tiefen See 45
D-64239 Darmstadt
Tel. +49 6151 803-0
Fax +49 6151 803-9100
www.hbm.com
Mat.: 7-2002.2781
DVS: A2781-3.1 HBM: public
10.2015
EHottinger Baldwin Messtechnik GmbH.
Subject to modifications.
All product descriptions are for general information only.
They are not to be understood as a guarantee of quality or
durability.
Änderungen vorbehalten.
Alle Angaben beschreiben unsere Produkte in allgemeiner
Form. Sie stellen keine Beschaffenheits- oder Haltbarkeits
garantie dar.
Sous réserve de modifications.
Les caractéristiques indiquées ne décrivent nos produits
que sous une forme générale. Elles n'impliquent aucune
garantie de qualité ou de durablilité.
Operating Manual | Bedienungsanleitung |
Manuel d'emploi |
English Deutsch Français
CMD
Digital charge amplifier
2A2781-3.1 HBM: public CMD
English
1 Safety instructions 5........................................
2 Markings used 11............................................
2.1 The markings used in this document 11..........................
3 Symbols on the device 12....................................
4 Scope of supply and accessories 13..........................
5 Conditions on site 15........................................
5.1 Ambient temperature 16.......................................
5.2 Moisture and humidity 16......................................
6 Mounting 17.................................................
7 Device description 19........................................
7.1 SYSTEM input/output 20......................................
7.2 Status LED 21................................................
7.3 Sensor connection 22.........................................
7.4 Ethernet interface 23..........................................
7.5 Digital input, digital outputs 23..................................
7.6 Principle of operation 25.......................................
7.7 The measuring chain 26.......................................
7.8 Voltage supply, control inputs and analog outputs 29..............
7.9 Low‐pass filter 30.............................................
7.10 High‐pass filter 30............................................
7.11 Peak value memory 30........................................
7.12 SensorTeach 30..............................................
7.14 TEDS transducer identification 35...............................
7.15 Hierarchy of rights for TEDS 36.................................
7.16 Content of the TEDS module as defined in IEEE 1451.4 37.........
7.17 Parameter sets 40............................................
CMD A2781-3.1 HBM: public 3
8 Starting up 42...............................................
8.1 Behavior of the CMD when switching on 43......................
8.2 Electrical connection 43.......................................
8.2.1 Connecting the sensors 44.....................................
8.2.2 SYSTEM input/output connection 45............................
8.2.3 Ethernet connection 46........................................
8.2.4 Digital input/digital outputs (optional)
(view of pins in the CMD) 48...................................
8.3 Installing the “CMD Assistant" parameterization software 48........
9 Software for parameterizing the CMD 50.......................
9.1 Settings example 51..........................................
9.2 Parameterization software command set 53......................
10 Error messages / operating state (LED display) 54.............
11 Updating the software (Update) 55............................
12 Updating the firmware (Update) 56............................
12.1 Updating the firmware (new procedure from Version 3.60) 56.......
12.2 Updating the firmware (old procedure up to Version 3.51) 58........
13 Maintenance 61..............................................
14 Tips for piezoelectric measurement technology 62.............
14.1 Functionality of piezoelectric sensors 62.........................
14.2 Available models and information on installation 65................
14.2.1 CFT force transducer 66.......................................
14.2.2 CFW force washer 66.........................................
14.3 Information about the charge amplifier and electrical connection 68..
14.4 Thermal influences 71.........................................
14.5 Mechanical influences 72......................................
14.6 Selection of components 74....................................
Safety instructions
CMD A2781-3.1 HBM: public 5
1 Safety instructions
Appropriate use
The device is to be used exclusively for measurement
tasks and directly related control tasks within the applica
tion limits detailed in the specifications. Use for any pur
pose other than the above is deemed to be non‐desig
nated use.
Any person instructed to carry out installation, commis
sioning or operation of the device must have read and
understood the Operating Manual and in particular the
technical safety instructions.
In the interests of safety, the device should only be oper
ated by qualified personnel and as described in the Oper
ating Manual. It is also essential to comply with the legal
and safety requirements for the application concerned
during use. The same applies to the use of accessories.
The device is not intended for use as a safety compo
nent. Please also refer to the “Additional safety precau
tions" section. Proper and safe operation requires proper
transportation, correct storage, siting and mounting, and
careful operation.
Operating conditions
SProtect the device from direct contact with water.
SProtect the device from moisture and weather such as
rain or snow. To comply with the degree of protection
under the DIN EN60529 standard, all the cables must
be connected and any connectors not in use must be
fitted with protective caps
SDo not expose the device to direct sunlight
Safety instructions
6A2781-3.1 HBM: public CMD
SAs specified in EN 61326-1, Section 3.6, the connect
ing cables of the device must be no longer than 30 m
(when laid within a building) and must not leave the
building.
SThe CMD housing must be grounded to achieve EMC.
SComply with the maximum permissible ambient tem
peratures and the data on maximum humidity as
stated in the specifications.
SThe device must not be modified from the design or
safety engineering point of view except with our
express agreement. In particular, any repair or solder
ing work on motherboards (exchanging components)
is prohibited. When exchanging complete modules,
use only original parts from HBM.
SThe device is delivered from the factory with a fixed
hardware and software configuration. Changes can
only be made within the possibilities documented in
the manuals.
SThe device is maintenance free.
SPlease note the following points when cleaning the
housing (also see Chapter 13, page 61):
SDisconnect the device from all current and voltage
supplies before cleaning it.
SClean the housing with a soft, slightly damp (not wet!)
cloth. Never use solvent as this could damage the
labeling or the housing.
SWhen cleaning, ensure that no liquid gets into the
device or connections.
SIn accordance with national and local environmental
protection and material recovery and recycling regula
tions, old equipment that can no longer be used must
Safety instructions
CMD A2781-3.1 HBM: public 7
be disposed of separately and not with normal house
hold garbage, see Chapter 15, page 80.
Additional safety precautions
Additional safety precautions to meet the requirements of
the relevant national and local accident prevention regu
lations must be taken in plants where malfunctions could
cause major damage, loss of data or even personal
injury.
The scope of supply and performance of the device cov
ers only a small area of measurement technology. Before
starting up the device in a system, a project planning and
risk analysis must first be implemented, taking into
account all the safety aspects of measurement and auto
mation technology so that residual dangers are mini
mized. This particularly concerns personal and machine
protection. In the event of a fault, the relevant precau
tions must establish safe operating conditions.
General dangers of failing to follow the safety
instructions
The device is state of the art and reliable. The device
may give rise to residual dangers if it is inappropriately
installed or operated.
Warning signs and danger symbols
Important instructions for your safety are specifically
identified. It is essential to follow these instructions in
order to prevent accidents and damage to property.
Safety instructions
8A2781-3.1 HBM: public CMD
The safety instructions take the following form:
WARNING
Type of danger
Consequences of non‐compliance
Averting the danger
-Warning sign:
draws attention to the danger
-Signal word:
indicates the severity of the danger (see table
below)
-Type of danger:
mentions the type or source of the danger
-Consequences:
describes the consequences of non‐compliance
-Averting:
indicates how the danger can be avoided/bypassed
Questo manuale è adatto per i seguenti modelli
3
Indice
Lingue:
Altri manuali HBM Amplificatore
