HH Electronics Tensor-SOLO Manuale utente
USER MANUAL
Page 1
CONTENTS
TENSOR-SOLO OVERVIEW .............................................................................................................................. 2
FEATURES ......................................................................................................................................................2
WHAT’S INCLUDED ...................................................................................................................................... 2
SETUP .................................................................................................................................................................. 3
CONTROLS......................................................................................................................................................... 3
CHANNELS 1/2.............................................................................................................................................. 4
CHANNELS 3/4.............................................................................................................................................. 4
MASTER CONTROLS .................................................................................................................................... 5
MAINS INLET .................................................................................................................................................6
SPECIFICATIONS ............................................................................................................................................... 7
BLACK............................................................................................................................................................. 7
WHITE............................................................................................................................................................. 8
DIMENSIONS.................................................................................................................................................9
SAFETY AND WARNINGS...............................................................................................................................10
Page 2
TENSOR-SOLO OVERVIEW
The Tensor-SOLO all-in-one column PA delivers a superior audio experience from an ultra portable
system. The 8" subwoofer and six 2.75”drivers allow for crystal clear audio coverage for 100+ people.
With its simple 4-piece ‘slot together’ design, the Tensor-SOLO can be set up swiftly and effortlessly.
Microphones or line level devices such as keyboards can connect to the Tensor-SOLO simultaneously
via the 4-channel mixer. Bluetooth enabled devices can also connect for wireless audio streaming and
with integrated True Wireless Stereo technology (TWS), two Tensor-SOLO systems can be linked for
stereo audio transmission wirelessly. The on-board DSP provides 4 EQ presets for different voicings
as well as comprehensive audio protection to prevent the system being overloaded. Carry bag and
slip cover are included, and its super-lightweight –weighing just 13Kg, 29lbs; the Tensor-SOLO is the
ultimate wireless audio solution.
FEATURES
•Ultra-lightweight 4 piece design weighing only 13Kg
•Impressive audio performance –perfect for 100+ people
•High power ensuring impressive coverage without compression
•4-channel mic/line mixer with built-in reverb
•Bluetooth connectivity including TWS system linking
•4x DSP presets for swift and effortless setup
•Available in black (Tensor-SOLO-BK) or white (Tensor-SOLO-WH)
WHAT’S INCLUDED
•Main Subwoofer unit
•1x top column loudspeaker
•2x top column spacers
•Padded slip cover for subwoofer
•Padded 3 piece column carry bag
•IEC power cable
Page 3
SETUP
The Tensor-SOLO may be used with either one or two spacer units depending on the unit’s position
and your chosen usage. For floor mounted operation, two spacers are recommended.
Position the subwoofer on a stable surface in the desired location, then proceed to fit the spacer
columns by firmly pressing them into position. Finally insert the column loudspeaker, ensuring all
joints are firmly pushed into position.
Care must be taken to position the unit to avoid causing a hazard, ensuring it cannot be knocked or
tripped over. If in doubt the unit should be secured in place.
A. Tensor-SOLO Subwoofer and amplifier
B. Two identical spacer pillars
C. Column loudspeaker
Page 4
CONTROLS
CHANNELS 1/2
1. LEVEL CONTROL
Controls the input level individually for channels 1
and 2. Set to minimum when first setting up your
inputs and gradually increase to a suitable volume.
2. LINE/MIC SWITCH
Switch to adjust gain for each channel. 40dB
added in the MIC setting for lower level inputs.
0dB added in LINE mode.
3. REVERB SWITCH
Toggle the internal reverb for each channel
individually. Reverb level is controlled separately.
4. XLR/6.3mm COMBI JACKS
Channel 1 and 2 inputs take either XLR or 6.3mm
jack. Can connect balanced or unbalanced signals.
CHANNELS 3/4
5. LEVEL CONTROL
Set the input level for both line level channels 3 & 4. Set to
minimum when first setting up your inputs and gradually
increase to a suitable volume.
6. BLUETOOTH INDICATOR
The blue LED indicates the Bluetooth status. Flashing indicates
attempting to connect and a solid blue light indicates a
connection. Short press the button to connect to your device –
it will show as ‘HH-Tensor’.
To connect a second system, hold the TWS button with a
device already connected. Then hold the TWS button on your
second system that will then auto pair.
7. AUX AND RCA INPUTS
A pair of RCA phono sockets and a single 3.5mm stereo
socket for auxiliary audio. Intended for line level audio use.
Both inputs may be used simultaneously.
Page 5
MASTER CONTROLS
8. MASTER VOLUME
Control the overall volume of all 4
channels. Set to minimum when setting
up inputs and gradually turn up to a
suitable volume.
Power LED will light green when the
system is powered on. The same LED
will turn red when the signal is being
limited by the onboard limiters.
Occasional flashing of red is ok
however avoid continuous illumination
of red limit light. Turn the master
volume down if so.
9. REVERB LEVEL
Set the reverb level for channel 1/2
reverbs. Will only work if the reverb
switches (3) are on.
10. DSP PRESET SELECT
4 EQ presets are loaded onto the Tensor-SOLO to enhance your sound depending on the use case.
Use the button to cycle through each preset. The 4 green LEDs will light one at a time to signal the
corresponding preset that is currently selected. The 4 green LEDs indicate which preset is currently
active.
MUSIC –Bass and treble lift with flat mids
BAND –Bass lift, flat mids and a slight treble cut off
NATURAL –Mostly flat with a slight bass and treble cut off
SPEECH –Large bass roll off and otherwise flat –intended for use with microphones
11. MIX OUT
Line level output that includes all 4 channels and is pre master volume.
Page 6
MAINS INLET
12.VOLTAGE SELECT SWITCH
The Tensor-SOLO is a dual voltage device, capable of being used around the world.
This switch should be correctly set for your country already. Although every effort has been made to
select the correct voltage for the region of use, it is advised that this is checked before first powering
on. Damage could occur if the voltage is incorrectly set.
Only change this setting with the mains cord unplugged and ensure it is set correctly before
powering on. Fuse change (14) will be required if the voltage is switched.
13. POWER SWITCH
Turns the system on and off. It is good practice to keep the master volume at minimum when
switching on and off.
14. MAINS INLET SOCKET
IEC input to connect the provided mains lead.
The safety fuse is included in the pull out drawer. Only replace the fuse with the type and value
indicated on the rear panel.
Page 7
SPECIFICATIONS
BLACK
Model
Tensor-SOLO:BK
Colour
Black
System Type
Ultra Portable Column PA System
Frequency response
50-20kHz
Max SPL (1M)
(Peak)
123 dB SPL
Power Rating
300W RMS, 1200W Peak
Amplifier Type
Class D
Power Supply
Universal SMPS 100-240V~
Protection
Short circuit, Thermal overload, multi band limiter
Inputs
2x Combo (XLR/Jack) balanced/unbalanced input with Mic/Line preset switch.
3.5mm Stereo Aux in, 2x RCA, Bluetooth V5.0 Audio Receiver
Outputs
Balanced XLR mix out.
Controls
CH1-3 Level, CH1-2 Reverb on/off switch, Master Volume, Bluetooth Pairing, EQ
preset
LF Driver
8" HH Long Throw Woofer
Hi/Mid Drivers
6x 2.75"
Cabinet
Robust Polypropylene Enclosure (Sub), ABS (Sat)
Accessories
1x Padded Subwoofer Slip Cover, 1x Padded 3 Piece Column Carry Bag included
Other
Illuminating HH Logo
Dimensions
Overall Height
(assembled)
1975mm, (77.8")
Overall Weight
(assembled)
14.1Kg, 31.1 lbs
Top Unit
dimensions (HWD)
560 x 105 x 105mm, 22" x 4.1" x 4.1" (560 x 105 x 105mm, 22" x 4.1" x 4.1"
Spacers)
Top Unit Weight
1.7Kg, 3.7 lbs (1.1Kg, 2.4 lbs Spacers)
Sub Unit
dimensions (HWD)
403 x 320 x 300mm, 15.9" x 12.6" x 11.8"
Sub Unit Weight
9Kg, 19.8 lbs
Carton dimensions
(HWD)
660 x 510 x 420mm, 26" x 20.1" x 16.5" (0.142 M3)
Packed Weight (Inc
Accessories)
17.1Kg, 37.7 lbs
EAN13
5060109458626
Page 8
WHITE
Model
Tensor-SOLO:WH
Colour
White
System Type
Ultra Portable Column PA System
Frequency response
50-20kHz
Max SPL (1M) (Peak)
123 dB SPL
Power Rating
300W RMS, 1200W Peak
Amplifier Type
Class D
Power Supply
Universal SMPS 100-240V~
Protection
Short circuit, Thermal overload, multi band limiter
Inputs
2x Combo (XLR/Jack) balanced/unbalanced input with Mic/Line preset switch.
3.5mm Stereo Aux in, 2x RCA, Bluetooth V5.0 Audio Receiver
Outputs
Balanced XLR mix out.
Controls
CH1-3 Level, CH1-2 Reverb on/off switch, Master Volume, Bluetooth Pairing, EQ
preset
LF Driver
8" HH Long Throw Woofer
Hi/Mid Drivers
6x 2.75"
Cabinet
Robust Polypropylene Enclosure (Sub), ABS (Sat)
Accessories
1x Padded Subwoofer Slip Cover, 1x Padded 3 Piece Column Carry Bag included
Other
Illuminating HH Logo
Dimensions
Overall Height
(assembled)
1975mm, (77.8")
Overall Weight
(assembled)
14.1Kg, 31.1 lbs
Top Unit dimensions
(HWD)
560 x 105 x 105mm, 22" x 4.1" x 4.1" (560 x 105 x 105mm, 22" x 4.1" x 4.1"
Spacers)
Top Unit Weight
1.7Kg, 3.7 lbs (1.1Kg, 2.4 lbs Spacers)
Sub Unit dimensions
(HWD)
403 x 320 x 300mm, 15.9" x 12.6" x 11.8"
Sub Unit Weight
9Kg, 19.8 lbs
Carton dimensions
(HWD)
660 x 510 x 420mm, 26" x 20.1" x 16.5" (0.142 M3)
Packed Weight (Inc
Accessories)
17.31Kg, 38.2 lbs
EAN13
5060109458633
Page 9
DIMENSIONS
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali HH Electronics Altoparlanti
HH Electronics
HH Electronics TESSEN TNi-W8PRO Manuale utente
HH Electronics
HH Electronics Tensor TRE-1001 Manuale utente
HH Electronics
HH Electronics Tensor TRM-1201 Manuale utente
HH Electronics
HH Electronics VECTOR VRE-12 Manuale utente
HH Electronics
HH Electronics Tessen TNi-W4 Manuale utente
HH Electronics
HH Electronics Tessen TNi-W4 Manuale utente
HH Electronics
HH Electronics MZ Series Manuale utente
HH Electronics
HH Electronics TESSEN TNA-1200S-G2 Manuale utente
