HighPoint SSD7540 Manuale utente
1
SSD7540
8x M.2 Port to PCIe 4.0x16 NVMe RAID Controller
Quick Installation Guide
V1.08
2
System Requirements
PC Requirements
•System with a free PCIe4.0 (or 3.0) x16 slot
•Windows 11, 10 / Server 2022, 2019, 2016, 2012R2 / Microsoft
Hyper-V
•RHEL/Debian/Ubuntu/Fedora/Proxmox/Xenserver/ Rocky Linux
(Linux kernel 3.10 and later)
•Arch Linux (Kernel 5.17.5 and above)
•macOS 10.13.6 ~ macOS 13.x
SSD7540 Kit Content
•SSD7540 Controller Card
•Quick Installation Guide
3
SSD7540 Hardware
Front View
Full-Length anodized aluminum heat sink
PCIe 4.0 x16 Host Interface
Full Height form factor
0000
Low-Noise Cooling Fan
External power port
4
Hardware Installation
Step 1. On the rear of the SSD7540, remove the six screws that secure
the unit’s heat sink to the PCB.
Step 2. Carefully remove the fan’s power cable from the right-side of
the heatsink as shown below, then carefully flip the heatsink to the
left (like turning a page from a book).
Note: Take care when moving the heatsink to prevent damaging
the left fan’s power cable.
5
Step 3. After removing the casing, carefully turn it over to view the
thermal pad. The blue films must be removed from the pad before
reinstalling the panel. These films protect the pad from damage and
foreign objects prior to installation, however, they will also prevent the
thermal pad from conducting the heat away from the NVMe SSD's if
we don't remove it.
Step 4. These 8 screws are used to install the NVMe SSD’s.
Step 5. Please remove these screws from each of the M.2 slots.
6
Step 6. Gently insert the SSD into the slot.
Note: Please make sure all disks are clean before you insert them
into the slot to avoid unexpected situations.
Step 7. Refasten the screw to secure the SSD.
Repeat Steps 5 to 7 to install the remaining SSDs.
The following example shows eight Gen4 SSDs installed into Ports 1-8:
Step 8. After installing all SSDs, carefully flip the heatsink to the right.
Port
Port
Port
Port
Port
Port
Port
Port
7
Note: Make sure the SSDs are carefully, but securely installed into
each M.2 port. Loose connections can cause a variety of stability
and performance issues, and may ultimately result in data loss.
Step 9. Carefully reinsert in the power supply cable of the cooling fan
that was removed in step 2.
Step 10. On the rear of the SSD7540, refasten the 6 screws that were
removed in step 1.
Note
：
Make sure the aluminum cover is properly aligned with the
controller board (PCB), and that it makes full contact with the
8
thermal pad, before refastening it to the SSD7540. If the cover is
improperly installed, the fan and thermal pad will be unable to
sufficiently cool the NVMe SSD’s and controller componentry,
which may result in damage to the SSD’s or controller hardware,
performance loss, unstable I/O, and the loss of data.
Step 11. Power up the SSD external power supply
Note: If the external power supply is not powered on, the SSDs
may drop offline or remain undetected, which could lead to data
loss.
SSD7540 relies on two power sources to support eight SSDs;
power supplied through the PCIe bus, and power from the
system’s PSU via an external 6 pin PCIe power cable. If the
external cable is not connected, there will be insufficient power to
support all 8 SSD’s; this may cause the SSDs to drop offline.
9
Note
：
The SSD7540 does not require the external power cord
when used with Mac Pro 2019
.
Note: Please be sure to connect NVMe before using the product to
reduce the occurrence of unnecessary errors!
Note: Install the driver in the system first and then install the board
!
Connect 6 pin PCIe power cable
10
Resources
A variety of manuals, guides and FAQ’s are available for the SSD7540
RAID controller.
In addition, we recommend visiting the Software Downloads webpage
for the latest drivers, management interfaces, and installation guides.
For Software Downloads, Documentation and more information
about this product, please visit the following website:
https://www.highpoint-tech.com/gen4-nvme-m2
FAQ & Troubleshooting:
FAQ - HighPoint Technologies, Inc. (helpjuice.com)
Altri manuali per SSD7540
4
Indice
Altri manuali HighPoint Controllori
HighPoint
HighPoint Rocket 700L Series Manuale utente
HighPoint
HighPoint SSD7120 Manuale utente
HighPoint
HighPoint HPT366 Manuale di installazione e d'uso
HighPoint
HighPoint RR640L Manuale utente
HighPoint
HighPoint R1000 Series Manuale utente
HighPoint
HighPoint RocketRAID 3G mini-SAS HBA Series Manuale utente
HighPoint
HighPoint SSD7101A-1 Manuale utente
HighPoint
HighPoint RocketRAID 2722A Manuale utente
HighPoint
HighPoint SSD7749E Manuale utente
HighPoint
HighPoint SSD7180 Manuale utente
HighPoint
HighPoint Rocket 710L Manuale utente
HighPoint
HighPoint SSD7105 Manuale utente
HighPoint
HighPoint Rocket Dual eSATA 6Gb/s For Mac Manuale utente
HighPoint
HighPoint RocketU 1142A Manuale utente
HighPoint
HighPoint Rocket 700 Series Manuale utente
HighPoint
HighPoint RR64 L Series Manuale utente
HighPoint
HighPoint SSD7103 Manuale utente
HighPoint
HighPoint RocketU Quad USB3.0 Manuale utente
HighPoint
HighPoint SSD6202A Manuale utente
HighPoint
HighPoint SSD7580A Manuale utente
