Hioki 3551 Manuale utente

INSTRUCTION MANUAL

For...は専用機種。複数の場合は「/」で区切る。

不要の場合はとる。

形名を入力。複数の場合は「/」で区切る。

3551

品名を入力。

BATTERY HiTESTER

Contents

Introduction i

Inspection i

Safety ii

Precautions v

Organization of this Manual viii

Chapter 1 Overview 1

1.1 Product Overview 1

1.2 Features 2

Chapter 2 Names and Functions of Parts 3

Chapter 3 Specifications 11

3.1 General Specification 11

3.2 Measurement Range 15

3.2.1 Maximum Input Voltage 17

3.2.2 Dielectric Strength 18

Chapter 4 Standard Measurement 19

4.1 Preparing for Measurement 19

4.1.1 Replacing the Batteries 19

4.1.2 Connecting the 9418-10 AC ADAPTER 21

4.1.3 Connecting the Test Lead and

Remote Control Switch 23

4.2 Measurement Batteries 24

4.2.1 Notes On Measurement 24

4.2.2 Measurement 26

Chapter 5 Advanced Measurement Functions 31

5.1 Comparator Function 31

5.1.1 What is the Comparator Function? 31

5.1.2 Comparator Settings 32

5.1.3 Comparator Decision Result Table 37

5.1.4 Switching the Comparator On and Off 38

5.1.5 Changing the Comparator Number 39

5.2 Measurement Value Memory Function 40

5.2.1 Memory 40

5.2.2 Overwrite 42

5.2.3 Clear 43

5.2.4 Readout 44

5.2.5 Printing 45

5.3 Beeper On/Off Function 47

5.4 Hold Function 47

5.5 Moving Average Function 49

5.6 Zero Adjust Function 51

5.6.1 9465 Zero Adjustment 51

5.6.2 9460 Zero Adjustment 53

5.7 Battery Low Warning 54

5.8 Auto Power Off 55

5.9 Circuit Configuration between EXT.HOLD

and EXT.MEMO 57

5.10 Reset 57

5.11 AC Four-Terminal Method 59

5.12 Internal Resistance of Lead Storage

Batteries 61

Chapter 6 Maintenance 63

6.1 Troubleshooting 63

6.2 Message Reference 65

6.3 Cleaning 66

――――――――――――――――――――――――――――――――――――――

Inspection

――――――――――――――――――――――――――――――――――

ntroduction

nspection

Thank you for purchasing the HIOKI "3551 BATTERY

HiTESTER." To obtain maximum performance from the

instrument, please read this manual first, and keep it

handy for future reference.

When you receive the instrument, inspect it carefully to

ensure that no damage occurred during shipping. In

particular, check the accessories, panel switches, and

connectors. If damage is evident, or if it fails to operate

according to the specifications, contact your dealer or

Hioki representative.

Accessories

9465 PIN TYPE LEAD

9466 REMOTE CONTROL SWITCH

Spiral tubes large (4), small (2)

9377 CARRYING CASE

Zero adjustment board

Six LR6 alkaline batteries

Instruction Manual

Dust cover (for the printer interface)

Shipping

Use the original packing materials when reshipping the

instrument, if possible.

――――――――――――――――――――――――――――――――――――――

Safety

――――――――――――――――――――――――――――――――――

DANGE

This instrument is designed to comply with IEC 61010

Safety Standards, and has been thoroughly tested for

safety prior to shipment. However, mishandling

during use could result in injury or death, as well as

damage to the instrument. Be certain that you

understand the instructions and precautions in the

manual before use. We disclaim any responsibility for

accidents or injuries not resulting directly from

instrument defects.

･The symbol printed on the instrument

indicates that the user should refer to a

corresponding topic in the manual (marked

with the symbol) before using the relevant

function.

･In the manual, the symbol indicates

particularly important information that the

user should read before using the instrument.

Indicates DC (Direct Current).

Indicates the ON side of the power switch.

Indicates the OFF side of the power switch.

afety

Safety symbols

This manual contains information and warnings essential

for safe operation of the instrument and for maintaining

it in safe operating condition. Before using the

instrument, be sure to carefully read the following safety

notes.

iii

――――――――――――――――――――――――――――――――――――――

Safety

――――――――――――――――――――――――――――――――――

DANGE

Indicates that incorrect operation presents an

extreme hazard that could result in serious

injury or death to the user.

WARNIN

Indicates that incorrect operation presents a

significant hazard that could result in serious

injury or death to the user.

CAUTIO

Indicates that incorrect operation presents a

possibility of injury to the user or damage to the

instrument.

NOTE Indicates advisory items related to performance

or correct operation of the instrument.

The following symbols in this manual indicate the relative

importance of cautions and warnings.

――――――――――――――――――――――――――――――――――――――

Safety

――――――――――――――――――――――――――――――――――

Measurement categories (Overvoltage categories)

This instrument complies with CAT I safety requirements.

To ensure safe operation of measurement instruments, IEC

61010 establishes safety standards for various electrical

environments, categorized as CAT I to CAT IV, and called

measurement categories. These are defined as follows.

CAT I : Secondary electrical circuits connected to an AC

electrical outlet through a transformer or similar

device.

CAT II : Primary electrical circuits in equipment connected

to an AC electrical outlet by a power cord (portable

tools, household appliances, etc.)

CAT III: Primary electrical circuits of heavy equipment

(fixed installations) connected directly to the

distribution panel, and feeders from the

distribution panel to outlets.

CAT IV: The circuit from the service drop to the service

entrance, and to the power meter and primary

overcurrent protection device (distribution panel).

Higher-numbered categories correspond to electrical

environments with greater momentary energy. So a

measurement device designed for CAT III environments can

endure greater momentary energy than a device designed

for CAT II.

Using a measurement instrument in an environment

designated with a higher-numbered category than that for

which the instrument is rated could result in a severe

accident, and must be carefully avoided.

Never use a CAT I measuring instrument in CAT II, III, or

IV environments.

The measurement categories comply with the Overvoltage

Categories of the IEC60664 Standards.

――――――――――――――――――――――――――――――――――――――

Precautions

――――――――――――――――――――――――――――――――――

DANGE

When voltages higher than 30 Vrms, 42.4 Vpeak or

battery circuits with more than 60 VDC are to be

measured, be sure to establish the floating state

first. Carrying out such measurements in the

grounded state involves the risk of electric shock.

When measuring batteries, always ensure sufficient

ventilation. Sometimes sparks may occur when the

test leads are connected to batteries, which can

ignite any accumulated inflammable gases such as

hydrogen.

To avoid electric shock accidents, when measuring

batteries being charged wear proper protective gear

such as rubber gloves.

recautions

Follow these precautions to ensure safe operation and to

obtain the full benefits of the various functions.

Preliminary Check

Before using the instrument the first time, verify that it

operates normally to ensure that the no damage occurred

during storage or shipping. If you find any damage,

contact your dealer or Hioki representative.

――――――――――――――――――――――――――――――――――――――

Precautions

――――――――――――――――――――――――――――――――――

WARNIN

Do not allow the instrument to get wet, and do not

take measurements with wet hands. This may cause

an electric shock.

Do not use the instrument where it may be exposed

to corrosive or combustible gases. The instrument

may be damaged or cause an explosion.

Before using the instrument, make sure that the

insulation on the test leads is undamaged and that

no bare conductors are improperly exposed. Using

the instrument in such conditions could cause an

electric shock, so contact your dealer or Hioki

representative for replacements (Model 9465 PIN

TYPE LEAD).

Be sure to connect the SOURCE and SENSE

terminals (banana plugs) correctly. When using the

9460 CLIP TYPE LEAD WITH TEMPERATURE SENSOR,

also connect the TEMP SENSOR terminal (miniplug)

See Section 4.2, "Measurement Batteries" for details

of the connections.

To avoid injury or damage to the instrument, do not

attempt to measure AC voltage, or DC voltage

exceeding 60 V.

Do not apply a voltage between the SOURCE(+) and

SENSE(+) or SOURCE(-) and SENSE(-) terminals.

This could result in damage to the instrument.

50 VDC ma

Indice

Altri manuali Hioki Strumento di misura

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente