Hioki 3555 Manuale utente

INSTRUCTION MANUAL

For...は専用機種。複数の場合は「/」で区切る。

不要の場合はとる。

形名を入力。複数の場合は「/」で区切る。

3555

品名を入力。

BATTERY HiTESTER

http://www.911618.com/

http://www.911618.com/dianchiceshiyi/HIOKI-3555/

http://www.911618.com/jishuwenzhang/HIOKI-3555/

Contents

Introduction i

Inspection i

Safety ii

Precautions v

Organization of This Manual viii

Chapter 1 Overview 1

1.1 Product Overview 1

1.2 Features 1

Chapter 2 Names and Functions of Parts 3

Chapter 3 Specifications 9

3.1 General Specification 9

3.2 Measurement Range 12

3.2.1 Maximum Input Voltage 13

3.2.2 Dielectric Strength 14

Chapter 4 Standard Measurement 15

4.1 Preparing for Measurement 15

4.2 Measurement 16

Chapter 5 Advanced Measurement Functions 21

5.1 Comparator Function 21

5.1.1 What is the Comparator Function? 21

5.1.2 Changing the Comparator Settings 22

5.1.3 Comparator Decision Result Table 27

5.1.4 Switching the Comparator On and Off 28

5.1.5 Changing the Comparator Number 29

5.2 Beeper On/Off Function 29

5.3 Hold Function 30

5.4 Zero Adjust Function 30

5.5 Battery Low Warning 32

5.6 Auto Power Off 33

5.7 AC Four-Terminal Method 35

Chapter 6 Maintenance 37

6.1 Troubleshooting 37

6.2 Message Reference 38

6.3 Cleaning 39

――――――――――――――――――――――――――――――――――――――

Inspection

――――――――――――――――――――――――――――――――――

Introduction

Inspection

Thank you for purchasing the HIOKI "3555 BATTERY

HiTESTER." To obtain maximum performance from the

instrument, please read this manual first, and keep it

handy for future reference.

When you receive the instrument, inspect it carefully to

ensure that no damage occurred during shipping. In

particular, check the accessories, panel switches, and

connectors. If damage is evident, or if it fails to operate

according to the specifications, contact your dealer or

Hioki representative.

Accessories

9461 PIN TYPE LEAD

Six LR6 alkaline batteries

Instruction Manual

Shipping

Use the original packing materials when reshipping the

instrument, if possible.

――――――――――――――――――――――――――――――――――――――

Safety

――――――――――――――――――――――――――――――――――

DANGER This instrument is designed to comply with IEC 61010

Safety Standards, and has been thoroughly tested for

safety prior to shipment. However, mishandling

during use could result in injury or death, as well as

damage to the instrument. Be certain that you

understand the instructions and precautions in the

manual before use. We disclaim any responsibility for

accidents or injuries not resulting directly from

instrument defects.

･The symbol printed on the instrument

indicates that the user should refer to a

corresponding topic in the manual (marked

with the symbol) before using the relevant

function.

･In the manual, the symbol indicates

particularly important information that the

user should read before using the instrument.

Indicates DC (Direct Current).

Indicates the ON side of the power switch.

Indicates the OFF side of the power switch.

Safety

Safety symbols

This manual contains information and warnings essential

for safe operation of the instrument and for maintaining

it in safe operating condition. Before using the

instrument, be sure to carefully read the following safety

notes.

iii

――――――――――――――――――――――――――――――――――――――

Safety

――――――――――――――――――――――――――――――――――

DANGER Indicates that incorrect operation presents an

extreme hazard that could result in serious

injury or death to the user.

WARNING Indicates that incorrect operation presents a

significant hazard that could result in serious

injury or death to the user.

CAUTION Indicates that incorrect operation presents a

possibility of injury to the user or damage to the

instrument.

NOTE Indicates advisory items related to performance

or correct operation of the instrument.

The following symbols in this manual indicate the relative

importance of cautions and warnings.

――――――――――――――――――――――――――――――――――――――

Safety

――――――――――――――――――――――――――――――――――

Measurement categories (Overvoltage categories)

This instrument complies with CAT I safety requirements.

To ensure safe operation of measurement instruments, IEC

61010 establishes safety standards for various electrical

environments, categorized as CAT I to CAT IV, and called

measurement categories. These are defined as follows.

CAT I : Secondary electrical circuits connected to an AC

electrical outlet through a transformer or similar

device.

CAT II : Primary electrical circuits in equipment connected

to an AC electrical outlet by a power cord

(portabletools,household appliances, etc.)

CAT III : Primary electrical circuits of heavy

equipment (fixed installations) connected directly

to the distribution panel, and feeders from the

distribution panel to outlets.

CAT IV : The circuit from the service drop to the service

entrance, and to the power meter and primary

overcurrent protection device (distribution panel).

Higher-numbered categories correspond to electrical

environments with greater momentary energy. So a

measurement device designed for CAT III environments can

endure greater momentary energy than a device designed

for CAT II.

Using a measurement instrument in an environment

designated with a higher-numbered category than that for

which the instrument is rated could result in a severe

accident, and must be carefully avoided.

Never use a CAT I measuring instrument in CAT II, III, or

IV environments.

The measurement categories comply with the Overvoltage

Categories of the IEC60664 Standards.

――――――――――――――――――――――――――――――――――――――

Precautions

――――――――――――――――――――――――――――――――――

DANGER The floating voltage between input terminals and

ground is 60 V AC/DC. Do not attempt to measure

voltages exceeding 60 V with respect to ground. This

could result in injury or damage to the instrument.

When measuring batteries, always ensure sufficient

ventilation. Sometimes sparks may occur when the

test leads are connected to batteries, which can ignite

any accumulated inflammable gases such as hydrogen.

WARNING Before using the instrument, make sure that the

insulation on the test leads is undamaged and that no

bare conductors are improperly exposed. Using the

instrument in such conditions could cause an electric

shock, so contact your dealer or Hioki representative

for replacements (Model 9461, Model 9287-10).

Precautions

Follow these precautions to ensure safe operation and to

obtain the full benefits of the various functions.

Preliminary Check

Before using the instrument the first time, verify that it

operates normally to ensure that the no damage occurred

during storage or shipping. If you find any damage,

contact your dealer or Hioki representative.

――――――――――――――――――――――――――――――――――――――

Precautions

――――――――――――――――――――――――――――――――――

WARNING Be sure to connect the SOURCE and SENSE terminals

correctly. See Section 4.2, "Measurement" for details

of the connections.

To avoid injury or damage to the instrument, do not

attempt to measure AC voltage, or DC voltage

exceeding 50 V.

50 VDC max

Do not apply a voltage between the SOURCE(+) and

SENSE(+) or SOURCE(-) and SENSE(-) terminals. This

could result in damage to the instrument.

CAUTION ･This instrument is not designed to be entirely water- or

dust-proof. To avoid damage, do not use it in a wet or

dusty environment.

･Do not store or use the instrument where it could be

exposed to direct sunlight, high temperature or

humidity, or condensation. Under such conditions, the

instrument may be damaged and insulation may

deteriorate so that it no longer meets specifications.

･Do not use the instrument near a source of strong

electromagnetic radiation, or near a highly electrically

charged object. These may cause a malfunction.

vii

――――――――――――――――――――――――――――――――――――――

Precautions

――――――――――――――――――――――――――――――――――

NOTE ･Correct measurement may be impossible in the presence

of strong magnetic fields, such as near transformers

and high-current conductors, or in the presence of

strong electromagnetic fields such as near radio

transmitters.

･For safety reasons, when taking measurements, only

use the 9461 PIN TYPE LEAD provided with the

instrument, or the optional 9287-10 CLIP TYPE LEAD.

Service

･When sending the instrument for repair, remove the

batteries and pack carefully to prevent damage in transit.

Include cushioning material so the instrument cannot

move within the package. Be sure to include details of the

problem. Hioki cannot be responsible for damage that

occurs during shipment.

Indice

Altri manuali Hioki Apparecchiature di prova

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuale utente