Hioki BT3554 Manuale utente
EN
BT3554-01
BATTERY TESTER
BT3554
Instruction Manual
June 2016 Revised edition 1
BT3554A961-01 16-06H
Let's Start by Measuring a New Battery
To determine if a battery is worn out, measure the data of a new
battery. As a battery wears out, its internal resistance increases to
approximately 1.5 to 2 times (reference value) that of a new one.
Use these values as guidelines when determining the battery wear
judgment values.
Example: Changes in the internal resistance and voltage
due to battery wear
New battery
Internal resistance: 0.5 mΩ
Voltage: 2.0 V
(The above values are examples.)
Battery requiring replacement
1.0 mΩ(twice the value of a
new battery)
1.8 V (90% of the value of a
new battery)
Resistance has doubled...
Worn out
FAIL
Default value × 2
WARNING
Default value × 1.5
PASS
Default value
Discharge
capacity
Internal
resistance
Resistance
wear out limit
Failed
PassedPassedPassedPassed
Battery Tester Quick Guide
BT3554A961-01
1
2
3
4
5
6
7
Appx. Index
Basic Usage
1
Connect the test leads to the instrument. (Black) (Red)
Hold at least
1 sec.
2
Turn the instrument power on.
Check the clock settings when using the
instrument for the rst time. (p. 36)
3
Changing the ranges. (p. 39)
4
Turn on the auto-hold function and auto-
memory function.
(and are displayed.)
Auto-hold function: Holds measurement values automatically when they
become stable. (p. 75)
Auto-memory function: Automatically stores measurement values
immediately after they are held. (p. 76)
5
Connect the test leads to the battery.
(Black)(Red)
−+
Data is stored
in internal
memory.
6
Press the key to read out the
measurement values. (p. 69)
Handy Features
Comparator function
With the comparator function, the threshold values can be set to
determine if the battery is worn out. (p. 55)
Setting examples of the battery wear judgment values
New battery
Resistance: 0.5 mΩ
Voltage: 2.0 V
(The above values are examples.)
In use
0.75 mΩ(1.5 times the
value of a new battery)
1.8 V (90% of the value
of a new battery)
Battery requiring
replacement
1.0 mΩ(twice the
value of a new battery)
PASS
(Passing limit) WARNING
(Warning limit) FAIL
(Failure limit)
1
2
3
4
5
6
7
Appx. Index
Downloading measurement values to a computer
By connecting the instrument to a computer with the included USB
cable, the measurement data can be downloaded to the computer.
(p. 83)
Viewing measurement values on a mobile device (only
for BT3554-01)
With the Bluetooth®Communication function, the measurement data
can be viewed on a smart phone or tablet. (p. 84)
i
Contents
Introduction.........................................................................1
Verifying Package Contents..............................................2
Options (Sold Separately)..................................................3
Safety Information..............................................................6
Operating Precautions.....................................................11
1 Overview 19
1.1 Measuring Battery Wear...............................19
1.2 Overview ........................................................21
1.3 Features .........................................................22
1.4 Names and Functions of Parts ....................24
1.5 Dimensions....................................................29
2 Measurement Preparations 31
2.1 Attaching the Neck Strap .............................31
2.2 Installing/Replacing Alkaline Batteries.......32
2.3 Connecting the Test Lead.............................33
Connecting a Pin Type Lead and the Model
9466 Remote Control Switch....................................34
2.4 Turning the Power ON/OFF ..........................35
2.5 Clock Function ..............................................36
Turning the Date and Time Display ON/OFF............36
Adjusting the Date and Time.....................................36
3 Measurement 37
3.1 Pre-operation Inspection..............................38
3.2 Setting the Measurement Range .................39
3.3 Adjusting Zero Value
(Zero Adjustment) .........................................40
8
9
1
2
3
4
5
6
7
Appx. Index
ii
Contents
Shorting Methods for Various Test Leads.................41
Performing Zero Adjustment.....................................44
Zero Adjustment Troubleshooting.............................46
Canceling the Zero Adjustment Operation................46
3.4 Retaining the Displayed Values...................47
Canceling the Retaining State..................................47
When retaining with the Model 9466 Remote
Control Switch...........................................................48
3.5 Determining Battery-wear Judgment
Values.............................................................49
3.6 Measuring a Battery (Inspection) ................50
Error Measurements.................................................52
Warning Display........................................................52
3.7 Measuring the Temperature .........................53
Changing the temperature display unit.....................54
4 Comparator Function (Evaluation by
Threshold Values) 55
4.1 Overview ........................................................55
4.2 Turning On the Comparator Function.........56
4.3 Setting Threshold Values for the
Comparator....................................................57
Comparison Table for the Comparator......................61
4.4 Setting the Comparator Buzzer ...................63
4.5 Canceling the Comparator Function...........64
5 Memory Function 65
5.1 Overview ........................................................65
Memory Structure.....................................................65
5.2 Storing Data in the Memory .........................66
5.3 Canceling the Memory Function..................68
5.4 Reading Out Stored Data..............................69
iii
Contents
5.5 Clearing Stored Data.....................................70
Clearing a Single Set of Data ...................................70
Clearing Data from Each Unit...................................71
Clearing All Data.......................................................72
6 Other Features 73
6.1 Noise Frequency Avoidance Function........73
6.2 Auto-hold Function.......................................75
6.3 Auto-memory Function.................................76
6.4 Auto Power Save Function (APS)................77
6.5 Backlight........................................................78
6.6 System Reset.................................................79
Default Settings (Factory Defaults)...........................80
6.7 Battery Level Warning ..................................81
7 Communications Function 83
7.1 Communicating with a Computer................83
7.2 Communicating with a Smart Phone or
Tablet (Only for BT3554-01)..........................84
Installing the smartphone app GENNECT Cross......85
Turning ON/OFF the Bluetooth®function..................86
Pairing the app with the battery tester (BT3554-01).87
Making measurements with the Bluetooth®function.88
8 Specications 89
8.1 GeneralSpecications .................................89
8.2 BasicSpecications .....................................91
8.3 AccuracySpecications...............................93
8.4 FunctionalSpecications.............................95
8.5 CommunicationSpecications..................102
1
2
3
4
5
6
7
8
9
Appx.
iv
Contents
9 Maintenance and Service 103
9.1 Repair, Inspection, Cleaning......................103
9.2 Troubleshooting..........................................105
Before Returning for Repair....................................105
9.3 Error Messages ...........................................107
9.4 Frequently Asked Questions......................108
9.5 Replacing the Fuse .....................................109
9.6 Replacing the Test Lead’s Tip Pin .............110
9.7 Disposing the Instrument (Removing
the Lithium Battery) ....................................112
Appendix Appx.1
Appx. 1 Effect of Extending the Test Lead
and Induced Voltage.........................Appx.1
Reducing Induced Voltage............................Appx.1
Appx. 2 Effect of Eddy Currents....................Appx.2
Appx. 3 AC 4-terminal Measurement Method .
Appx.3
Appx. 4 Effects of Current Density ...............Appx.5
When the Measurement target is Wide or
Thick.............................................................Appx.5
Appx. 5 Synchronous Detection System......Appx.7
Appx. 6 Calibration.........................................Appx.8
Calibrating the Resistance Measurement
Component...................................................Appx.8
Calibrating the Voltage Measurement Unit...Appx.9
Altri manuali per BT3554
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Hioki Apparecchiature di prova
Hioki
Hioki 3444 Manuale utente
Hioki
Hioki IR4059 Manuale utente
Hioki
Hioki 3255 Manuale utente
Hioki
Hioki 3665-20 Manuale utente
Hioki
Hioki BT3554-50 Manuale utente
Hioki
Hioki MR8827 Manuale utente
Hioki
Hioki 3145 Manuale utente
Hioki
Hioki BT3554-50 Manuale utente
Hioki
Hioki 3561 Manuale utente
Hioki
Hioki 3511-50 Manuale utente
Hioki
Hioki 3805-50 Manuale utente
Hioki
Hioki ST4030 Manuale utente
Hioki
Hioki SS9000 Manuale utente
Hioki
Hioki HiLogger 3145-20 Manuale utente
Hioki
Hioki 9455 Manuale utente
Hioki
Hioki CLAMP ON LEAK HiTESTER 3283 Manuale utente
Hioki
Hioki IR4051 Manuale utente
Hioki
Hioki 3159 Manuale utente
Hioki
Hioki FT6031-50 Manuale utente
Hioki
Hioki MO HiTESTER 3452 Manuale utente
Manuali Apparecchiature di prova popolari di altre marche
SMART
SMART KANAAD SBT XTREME 3G Series Manuale utente
Agilent Technologies
Agilent Technologies BERT Serial Manuale utente
Agilent Technologies
Agilent Technologies N3280A Manuale utente
Vernier
Vernier Go Direct Voltage Manuale utente
Lifeloc
Lifeloc R.A.D.A.R. Manuale utente
Fluke
Fluke T5-600 Istruzioni per l'uso e l'installazione
