Hirschmann OCTOPUS OS3 Manuale utente

Installation OCTOPUS OS3

Release

02/2019

Technical support

https://hirschmann-support.belden.com

User Manual

Installation

Managed Ethernet Switch

OCTOPUS OS3

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use.

The performance features described here are binding only if they have been expressly agreed

when the contract was made. This document was produced by Hirschmann Automation and

Control GmbH according to the best of the company's knowledge. Hirschmann reserves the right

to change the contents of this document without prior notice. Hirschmann can give no guarantee

in respect of the correctness or accuracy of the information in this document.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

You can get the latest version of this manual on the Internet at the Hirschmann product site

(www.hirschmann.com).

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

8.2.19

Installation OCTOPUS OS3

Release

02/2019 3

Contents

Safety instructions 5

About this manual 10

Key 11

1 Description 12

1.1 General device description 12

1.2 Device name and product code 12

1.3 Device views 14

1.3.1 Front view 14

1.4 Power supply 15

1.4.1 Supply voltage with the characteristic value N9 15

1.5 Ethernet ports 15

1.6 Pin assignments 16

1.7 Display elements 17

1.7.1 Device state 17

1.7.2 Port Status 19

1.8 Management interfaces 20

1.8.1 V.24 interface (external management) 20

1.8.2 USB interface 20

1.9 Input/output interfaces 21

1.9.1 Signal contact 21

2 Installation 22

2.1 Checking the package contents 22

2.2 Installing and grounding the device 23

2.2.1 Mounting on a flat surface 23

2.2.2 Grounding the device 24

2.3 Connecting the supply voltage 25

2.4 Connecting data cables 26

3 Basic Settings 27

4 Monitoring the ambient air temperature 28

5 Maintenance and service 29

4Installation OCTOPUS OS3

Release

02/2019

6Disassembly 30

6.1 Removing the device 30

7 Technical data 31

7.1 General data 31

7.2 Supply voltage 31

7.3 Signal contact 32

7.4 Power consumption/power output 32

7.5 Climatic conditions during operation 33

7.6 Climatic conditions during storage 33

7.7 Dimension drawings 34

7.8 EMC and immunity 35

7.9 Network range 38

8 Scope of delivery, order numbers and

accessories 39

8.1 Scope of delivery 39

8.2 Accessories 39

9 Underlying technical standards 40

A Further support 41

Installation OCTOPUS OS3

Release

02/2019 5

Safety instructions

General safety instructions

You operate this device with electricity. Improper usage of the device

entails the risk of physical injury or significant property damage. The

proper and safe operation of this device depends on proper handling

during transportation, proper storage and installation, and careful

operation and maintenance procedures.

Before connecting any cable, read this document, and the safety

instructions and warnings.

Operate the device with undamaged components exclusively.

The device is free of any service components. In case of a damaged

or malfunctioning device, turn off the supply voltage and return the

device to Hirschmann for inspection.

National and international safety regulations

Verify that the electrical installation meets local or nationally applicable

safety regulations.

Certified usage

Use the product only for the application cases described in the

Hirschmann product information, including this manual.

Operate the product only according to the technical specifications.

See “Technical data” on page 31.

Connect to the product only components suitable for the requirements

of the specific application case.

WARNING

UNCONTROLLED MACHINE ACTIONS

To avoid uncontrolled machine actions caused by data loss, configure all

the data transmission devices individually.

Before you start any machine which is controlled via data transmission, be

sure to complete the configuration of all data transmission devices.

Failure to follow these instructions can result in death, serious injury,

or equipment damage.

6Installation OCTOPUS OS3

Release

02/2019

Qualification requirements for personnel

Only allow qualified personnel to work on the device.

Qualified personnel have the following characteristics:

Qualified personnel are properly trained. Training as well as practical

knowledge and experience make up their qualifications. This is the

prerequisite for grounding and labeling circuits, devices, and systems

in accordance with current standards in safety technology.

Qualified personnel are aware of the dangers that exist in their work.

Qualified personnel are familiar with appropriate measures against

these hazards in order to reduce the risk for themselves and others.

Qualified personnel receive training on a regular basis.

Installation site requirements

Verify that there is at least 4 in (10 cm) of space above and below the

device.

Install this device solely in an operating site with restricted access, to

which maintenance staff have exclusive access. Install the device in

such a way that it is protected against mechanical forces in the area of

the power supply.

Device casing

Only technicians authorized by the manufacturer are permitted to open

the casing.

Never insert pointed objects (narrow screwdrivers, wires, etc.) into the

device or into the connection terminals for electric conductors. Do not

touch the connection terminals.

Keep the cooling fins free to ensure good air circulation.

The surfaces of the device housing may become hot. Avoid touching

the device while it is operating.

To preserve the suitability of your device for IP54, seal all unused

connections and ports with the provided plastic protection screws. See

“Scope of delivery” on page 39. See “Scope of delivery” on page 39 in

case of an additional demand.

To preserve the IP54 suitability for your device, exclusively connect

components with degree of protection IP54.

For operation according to EN 45545: Seal all unused connections

and ports exclusively with metal protection screws and metal screw

caps. The use of plastic protection screws is prohibited.

Protection screws and screw caps made of metal are available as an

accessory.

See “Accessories” on page 39.

Installation OCTOPUS OS3

Release

02/2019 7

Grounding the device

Grounding the device is by means of a separate ground connection on the

device.

Ground the device before connecting any other cables.

Disconnect the grounding only after disconnecting all other cables.

The overall shield of a connected shielded twisted pair cable is connected

to the grounding connector on the front panel as a conductor.

Requirements for connecting electrical wires

Before connecting the electrical wires, always verify that the

requirements listed are complied with.

General requirements for connecting electrical wires

The following requirements apply without restrictions:

The electrical wires are voltage-free.

The cables used are permitted for the temperature range of the application case.

Relevant for North America:

Exclusively use 60/75 °C (140/167 °F) or 75 °C (167 °F) copper (Cu) wire.

Requirements for connecting the signal contact

The following requirements apply without restrictions:

The connected voltage complies with the requirements for a safety extra-low voltage

(SELV) or ES1 as per IEC/EN 62368-1.

The connected voltage is limited by a current limitation device or a fuse.

Observe the electrical threshold values for the signal contact.

See “General data” on page 31.

Requirements for connecting the supply voltage

The following requirements apply without restrictions:

All of the following requirements are complied with:

The supply voltage corresponds to the voltage specified on the type plate of the device.

The power supply conforms to overvoltage category I or II.

The power supply has an easily accessible disconnecting device (for example a switch or

a plug). This disconnecting device is clearly identified. So in the case of an emergency, it is

clear which disconnecting device belongs to which power supply cable.

The wire diameter of the power supply cable is at least 1 mm² (North America: AWG16) on

the supply voltage input.

The following requirements apply alternatively:

Relevant when the device is supplied via 1 voltage input:

Relevant for North America:

The power supply complies with the requirements according to NEC Class 2.

8Installation OCTOPUS OS3

Release

02/2019

CE marking

The labeled devices comply with the regulations contained in the following

European directive(s):

2011/65/EU (RoHS)

Directive of the European Parliament and of the Council on the restriction

of the use of certain hazardous substances in electrical and electronic

equipment.

2014/30/EU (EMC)

Directive of the European Parliament and the council for standardizing the

regulations of member states with regard to electromagnetic

compatibility.

In accordance with the above-named EU directive(s), the EU conformity

declaration will be at the disposal of the relevant authorities at the

following address:

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

www.hirschmann.com

The device can be used in the industrial sector.

Interference immunity: EN 61000-6-2

Emitted interference: EN 55032

Safety: EN 62368-1

You find more information on technical standards here:

See “Technical data” on page 31.

Warning! This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take

appropriate measures.

Note: The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.

Installation OCTOPUS OS3

Release

02/2019 9

FCC note:

This device complies with part 15 of the FCC rules. Operation is subject

to the following two conditions: (1) this device may not cause harmful

interference; (2) this device must accept any interference received,

including interference that may cause undesired operation.

Appropriate testing has established that this device fulfills the

requirements of a class A digital device in line with part 15 of the FCC

regulations.

These requirements are designed to provide sufficient protection against

interference when the device is being used in a business environment.

The device creates and uses high frequencies and can also radiate these

frequencies. If it is not installed and used in accordance with this

operating manual, it can cause radio transmission interference. The use

of this device in a residential area can also cause interference, and in this

case the user is obliged to cover the costs of removing the interference.

Recycling note

After usage, this device must be disposed of properly as electronic waste,

in accordance with the current disposal regulations of your county, state,

and country.

10 Installation OCTOPUS OS3

Release

02/2019

About this manual

The “Installation” user manual contains a device description, safety

instructions, a description of the display, and the other information that you

need to install the device.

The following manuals are available on the Internet at https://

www.doc.hirschmann.com/ as downloads:

User Manual Installation

User Manual Basic Configuration

User Manual Redundancy Configuration

Reference Manual Graphical User Interface

Reference Manual Command Line Interface

Indice

Altri manuali Hirschmann Router di rete

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann OWL LTE Manuale utente

Hirschmann

Hirschmann MICE MS20-1600 Series Manuale utente

Hirschmann

Hirschmann RSR20-0900 Manuale utente

Hirschmann

Hirschmann RS2-5TX/FX Manuale

Hirschmann

Hirschmann MS30, Power MICE, MACH 4000, OCTOPUS Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann MACH 1020 Manuale utente

Hirschmann

Hirschmann MACH104-20TX-F Series Manuale utente

Hirschmann

Hirschmann RSB20 Manuale utente

Hirschmann

Hirschmann MICE MS20 Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann SPIDER-SL-40-08T1 Manuale utente

Hirschmann

Hirschmann OWL-IPG-AMERICAS Manuale utente

Hirschmann

Hirschmann PowerMICE Manuale utente

Hirschmann

Hirschmann GECKO 4TX Manuale utente

Hirschmann

Hirschmann OWL LTE M12 Manuale utente

Hirschmann

Hirschmann RSB20-0800T1T1 Manuale utente

Hirschmann

Hirschmann RS40 series Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann RS2-FX-LH/FX-LH Manuale

Hirschmann

Hirschmann MACH 4002 Family Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann OWL LTE M12 Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza