Hirschmann MACH 4000 Series Manuale utente

Basic - L3P

Release

4.0

11/07

Technical Support

[email protected]

User Manual

Basic Configuration

Industrial ETHERNET (Gigabit) Switch

Power MICE, MACH 4000

The naming of copyrighted trademarks in this manual, even when not specially indicated, should

not be taken to mean that these names may be considered as free in the sense of the trademark

and tradename protection law and hence that they may be freely used by anyone.

translation, conversion into any electronic medium or machine scannable form is not permitted,

either in whole or in part. An exception is the preparation of a backup copy of the software for

your own use. For devices with embedded software, the end-user license agreement on the en-

closed CD applies.

The performance features described here are binding only if they have been expressly guaran-

teed in the contract. This publication has been created by Hirschmann Automation and Control

GmbH according to the best of our knowledge. Hirschmann reserves the right to change the con-

tents of this manual without prior notice. Hirschmann can give no guarantee in respect of the

correctness or accuracy of the details in this publication.

Hirschmann can accept no responsibility for damages, resulting from the use of the network

components or the associated operating software. In addition, we refer to the conditions of use

specified in the license contract.

Printed in Germany

Hirschmann Automation and Control GmbH

Stuttgarter Str. 45-51

72654 Neckartenzlingen

Germany

Tel.: +49 1805 141538

Rel. 4.0-01-1107 – 27.11.07

Content

User Manual - Industrial Protocols

Release

4.0

11/07 3

Content

Content 3

About this Manual 9

Key 11

Introduction 13

1 Access to the user interfaces 15

1.1 System Monitor 16

1.2 Command Line Interface 18

1.3 Web-based Interface 21

2 Entering the IP Parameters 25

2.1 IP Parameter Basics 27

2.1.1 IP address (version 4) 27

2.1.2 Network mask 28

2.2 Entering IP parameters via CLI 32

2.3 Entering the IP Parameters via HiDiscovery 35

2.4 Loading the system configuration from the ACA 38

2.5 System configuration via BOOTP 40

2.6 System configuration via DHCP 45

2.7 System configuration via DHCP Option 82 48

2.8 System configuration via the Web-based interface 49

2.9 Faulty device replacement 51

3 Loading/saving settings 53

3.1 Loading settings 54

3.1.1 Loading from the local non-volatile memory 55

3.1.2 Loading from the AutoConfiguration Adapter 55

3.1.3 Loading from a file 56

3.1.4 Resetting the configuration to the state on delivery 58

Content

4User Manual - Industrial Protocols

Release

4.0

11/07

3.2 Saving settings 59

3.2.1 Saving locally (and on the ACA) 59

3.2.2 Saving in a file on URL 60

3.2.3 Saving in a binary file on the PC 61

3.2.4 Saving as a script on the PC 61

4 Loading software updates 63

4.1 Loading the software from the ACA 65

4.1.1 Selecting the software to be loaded 66

4.1.2 Starting the software 67

4.1.3 Performing a cold start 67

4.2 Loading the software from the tftp server 68

4.3 Loading the software via file selection 70

5 Configuring the ports 71

6 Protection from unauthorized access 75

6.1 Password for SNMP access 76

6.1.1 Description of password for SNMP access 76

6.1.2 Entering the password for SNMP access 77

6.2 Telnet/Web/SSH access 81

6.2.1 Description of Telnet access 81

6.2.2 Description of Web access 81

6.2.3 Description of SSH access 82

6.2.4 Enabling/disabling Telnet/Web/SSH access 83

6.3 Disabling the HiDiscovery function 84

6.3.1 Description of the HiDiscovery protocol 84

6.3.2 Enabling/disabling the HiDiscovery function 84

6.4 Port access control 85

6.4.1 Port access control 85

6.4.2 Defining port access control 86

6.5 Port authentication according to 802.1X 88

6.5.1 Description of port authentication according to 802.1X 88

6.5.2 Authentication process 89

6.5.3 Preparing the Switch for the

802.1X port authentication 89

6.5.4 Setting 802.1X 90

Content

User Manual - Industrial Protocols

Release

4.0

11/07 5

6.6 Access Control Lists (ACL). 91

6.6.1 Description of prioritizing with ACLs 92

6.6.2 Description of IP-based ACLs. 93

6.6.3 Description of MAC-based ACLs 94

6.6.4 Configuring IP ACLs 95

6.6.5 Configuring MAC ACLs 97

6.6.6 Configuring priorities with IP ACLs 98

6.6.7 Specifying the sequence of the rules 100

7 Synchronizing the system time in the network 101

7.1 Entering the time 102

7.2 SNTP 104

7.2.1 Description of SNTP 104

7.2.2 Preparing the SNTP coordination 105

7.2.3 Configuring SNTP 106

7.3 Precision Time Protocol 110

7.3.1 Description of PTP functions 110

7.3.2 Preparing the PTP configuration 114

7.3.3 Configuring PTP 115

7.4 Interaction of PTP and SNTP 118

8 Network load control 121

8.1 Direct packet distribution 122

8.1.1 Store-and-forward 122

8.1.2 Multi-address capability 122

8.1.3 Aging of learned addresses 123

8.1.4 Entering static address entries 124

8.1.5 Disabling the direct packet distribution 125

8.2 Multicast application 126

8.2.1 Description of the Multicast application 126

8.2.2 Example of a Multicast application 127

8.2.3 Description of IGMP Snooping 128

8.2.4 Description of GMRP 128

8.2.5 Setting up the Multicast application 130

8.3 Rate Limiter 135

8.3.1 Description of the Rate Limiter 135

8.3.2 Rate Limiter settings 135

Content

6User Manual - Industrial Protocols

Release

4.0

11/07

8.4 QoS/Priority 137

8.4.1 Description of Prioritization 137

8.4.2 VLAN tagging 138

8.4.3 IP ToS / DiffServ 140

8.4.4 Management prioritizing 143

8.4.5 Handling of received priority information 143

8.4.6 Handling of traffic classes 144

8.4.7 Setting prioritization 146

8.5 Flow control 152

8.5.1 Description of flow control 152

8.5.2 Setting the flow control 154

8.6 VLANs 155

8.6.1 Description of VLANs 155

8.6.2 Configuring VLANs 158

8.6.3 Example of a simple VLAN 161

9 Operation diagnosis 169

9.1 Sending traps 170

9.1.1 SNMP trap listing 171

9.1.2 SNMP traps when booting 172

9.1.3 Configuring traps 173

9.2 Monitoring the device status 175

9.2.1 Configuring the device status 176

9.2.2 Displaying the device status 176

9.3 Out-of-band signaling 178

9.3.1 Controlling the signal contact 179

9.3.2 Monitoring correct operation via the signal contact 180

9.3.3 Monitoring the device status via the signal contact 181

9.4 Port status indication 182

9.5 Event counter at port level 183

9.6 Displaying the SFP status 185

9.7 TP cable diagnosis 186

9.8 Topology discovery 187

9.8.1 Description of topology discovery 187

9.8.2 Displaying the topology discovery 188

9.9 Detecting IP address conflicts 191

Content

User Manual - Industrial Protocols

Release

4.0

11/07 7

9.9.1 Description of IP address conflicts 191

9.9.2 Configuring ACD 192

9.9.3 Displaying ACD 192

9.10 Reports 194

9.11 Monitoring port traffic (port mirroring) 196

A Setting up configuration environment 199

A.1 Setting up DHCP/BOOTP server 200

A.2 Setting up DHCP Server Option 82 206

A.3 tftp server for software updates 210

A.3.1 Setting up the tftp process 211

A.3.2 Software access rights 214

A.4 Preparing access via SSH 215

A.4.1 Generating a key 215

A.4.2 Uploading the key 216

A.4.3 Access via SSH 217

B General information 221

B.1 Management Information Base (MIB) 222

B.2 Abbreviations used 225

B.3 List of RFC's 226

B.4 Based specifications and standards 228

B.5 Technical Data 229

B.6 Copyright of integrated software 230

B.6.1 Bouncy Castle Crypto APIs (Java) 230

B.6.2 LVL7 Systems, Inc. 231

B.7 Reader´s comments 232

C Index 235

D Further support 239

Content

8User Manual - Industrial Protocols

Release

4.0

11/07

About this Manual

Basic - L3P

Release

4.0

11/07 1

About this Manual

The “Basic Configuration” user manual contains all the information you need

to start operating the switch. It takes you step by step from the first startup

operation through to the basic settings for operation in your environment.

The following thematic sequence has proven itself in practice:

XSet up device access for operation by entering the IP parameters

XCheck the status of the software and update it if necessary

XLoad/store the configuration

XConfigure the ports

XSet up protection from unauthorized access

XOptimize the data transmission with network load control

XSynchronize system time in the network

XFunction diagnosis

The “Installation” user manual contains a device description, safety instruc-

tions, a description of the display, and all the other information that you need

to install the device before you begin with the configuration of the device.

The “Redundancy Configuration” user manual contains all the information

you need to select a suitable redundancy procedure and configure it.

The “Industry Protocols” user manual describes how the Switch is connected

by means of a communication protocol commonly used in the industry, such

as EtherNet/IP and PROFINET.

The “Routing Configuration” user manual contains all the information you

need to start operating the routing function. It takes you step by step from

a small router application through to the router configuration of a complex

network.

The manual enables you to configure your router by following the examples.

About this Manual

2Basic - L3P

Release

4.0

11/07

The "Web-based Interface" reference manual contains detailed information

on using the Web interface to operate the individual functions of the switch.

The "Command Line Interface" reference manual contains detailed informa-

tion on using the Command Line Interface to operate the individual functions

of the switch.

The Network Management Software HiVision provides you with additional

options for smooth configuration and monitoring:

XEvent logbook.

XConfiguration of „System Location“ and „System Name“.

XConfiguration of the network address range and SNMP parameters.

XSaving the configuration on the Switch.

XSimultaneous configuration of multiple Switches.

XConfiguration of the port display color red for a connection error.

Altri manuali per MACH 4000 Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Hirschmann Router di rete

Hirschmann

Hirschmann HiSecOS EAGLE20 Manuale utente

Hirschmann

Hirschmann RS2-5TX/FX Manuale

Hirschmann

Hirschmann GigaLION-24TP Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann MACH104-20TX-FR Series Manuale utente

Hirschmann

Hirschmann MICE MS20 Manuale utente

Hirschmann

Hirschmann OCTOPUS OS3 Manuale utente

Hirschmann

Hirschmann HiSecOS EAGLE20 Manuale utente

Hirschmann

Hirschmann MM2-2FXM3/2TX1 Manuale

Hirschmann

Hirschmann OWL LTE M12 Manuale utente

Hirschmann

Hirschmann OWL 4G Europe Manuale utente

Hirschmann

Hirschmann PowerMICE Manuale utente

Hirschmann

Hirschmann OWL3G Manuale utente

Hirschmann

Hirschmann EAGLE30-0402 series Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann SPIDER Premium Line Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann RSR20-0900 Manuale utente

Hirschmann

Hirschmann MACH 4000 Series Manuale utente

Hirschmann

Hirschmann RS20 series Manuale utente

Hirschmann

Hirschmann MACH 4002 Family Manuale utente

Hirschmann

Hirschmann RS40 series Manuale utente

Hirschmann

Hirschmann GECKO 4TX Manuale utente

Hirschmann

Hirschmann RS20 series Manuale del proprietario

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza