Honeywell BSM Istruzioni per il montaggio

K14864V3 9/10 Rev. A

BSM

Battery Sense Module

INSTALLATION AND SETUP GUIDE

GENERAL INFORMATION

The Honeywell Battery Sense Module is a control panel

accessory that is used to monitor and report the backup

battery status. Its features are:

Monitors and reports for one or two batteries.

Detects and reports low battery conditions.

Detects and reports if a battery is removed.

Provides deep discharge battery protection if AC

power is lost and the backup battery voltage falls

below a safety threshold of 9.5 to 10 volts.

Additional modules can be used for those control panels

that use additional batteries.

PACKAGE CONTENTS

The following items are included:

Battery Sense Module with bracket

Battery Harness (qty 2)

Summary of Connections label

SPECIFICATIONS

Physical: 3-1/8” L x 2-3/4” W x 3/4” H

(80mm x 70mm x 20mm)

Electrical:

Input Voltage: 12VDC nominal (from control panel)

Input Current: 20mA (max used by BSM)

Current Handling Capability: 2.3A maximum

(Control panel load must not exceed 2.3A.)

INSTALLATION

1. Select a suitable area in the control panel where

the mounting will not interfere with testing or

servicing of other components.

2. Clip the Battery Sense Module to the cabinet edge.

CONNECTIONS

1. Refer to the Connections Diagram on other side.

When connecting leads, support the module to

prevent stress on the circuit board.

2. Connect the module's power leads to the control

panel's 12VDC backup battery power terminals.

3. Connect backup battery A to the module. Then

connect backup battery B (if present) to the module.

4. If only one backup battery is being used, depress

the ENROLLMENT switch to toggle the Battery

Sense Module to sense only one battery.

ULC

When used with one battery and the total

load is greater than 1.5A, jumper the

Battery A terminals and the Battery B

terminals on the Battery Sense Module to

the backup battery.

5. For non-Honeywell control panels, connect the

ZONE OUT to an unused control panel zone. (Do

not use a fire zone.)

Note: For Honeywell control panels, DO NOT

connect a zone to the ZONE OUT terminal on

the BSM. The Honeywell control panel will

automatically detect a low or missing battery

through the panel's battery cable.

6. Affix the supplied Summary of Connections label to

the inside of the control panel.

CONFIGURATION

1. Refer to the control panel's installation guide for

details on fault monitoring.

2. For non-Honeywell control panels, program the

connected zone for the Battery Sense Module to

detect an active high fault condition.

ZONE OUT

BAT

BSM-001-V0

B AT. A PANEL

B AT. B

DOCUMENTATION AND ONLINE SUPPORT

For the latest documentation and online support information, please go to:

http://www.security.honeywell.com/hsc/resources/MyWebTech/

WARRANTY

For the latest warranty information, please go to:

http://www.security.honeywell.com/hsc/resources/wa/

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

www.honeywell.com/security

ÊK14864V3cŠ

K14864V3 9/10 Rev. A

STATUS LEDs (A and B)

STEADY ON Battery is present and good.

BLINKING Battery is programmed to be

present, and is NOT present.

OFF Battery is NOT programmed to be

present.

ENROLLMENT Switch

Default condition is for 2

batteries.

Depress once for 1 battery.

To the control panel battery terminals.

To Battery A terminals.

To Battery B terminals.

To a non-Honeywell

control panel zone for

fault monitorin

Note:

For Honeywell control panels, DO NOT

connect a zone to the ZONE OUT ter-

minal on the BSM. The Honeywell

control panel will automatically detect

a low or missing battery through the

panel's battery cable.

Altri manuali Honeywell Unità di controllo

Honeywell

Honeywell VS8521 Manuale utente

Honeywell

Honeywell RA116A Manuale utente

Honeywell

Honeywell LYNXDM-GSM Istruzioni per il montaggio

Honeywell

Honeywell VR8200A Manuale utente

Honeywell

Honeywell D06F Manuale utente

Honeywell

Honeywell VR8405 Manuale utente

Honeywell

Honeywell TM300 Manuale utente

Honeywell

Honeywell HON 530-E-WG Guida

Honeywell

Honeywell R4140G Manuale utente

Honeywell

Honeywell 7800 SERIES Manuale utente

Honeywell

Honeywell DCCC6500 Manuale utente

Honeywell

Honeywell Elster Jeavons S300 Manuale utente

Honeywell

Honeywell NOTIFIER LDM Series Manuale utente

Honeywell

Honeywell V800 Manuale utente

Honeywell

Honeywell hmr3000 TruePoint Manuale utente

Honeywell

Honeywell L506 Manuale utente

Honeywell

Honeywell AlarmNet IGSMHS Istruzioni per il montaggio

Honeywell

Honeywell Krom Schroeder VAN Series Manuale utente

Honeywell

Honeywell NOTIFIER M700 Series Manuale utente

Honeywell

Honeywell M6410A Manuale operativo

Honeywell

Honeywell SmartValve SV9520H Manuale utente

Honeywell

Honeywell RM7824A Manuale operativo

Honeywell

Honeywell V5421C Manuale utente

Honeywell

Honeywell ControlEdge 900 platform Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente