Honeywell MicroMAX Pro Istruzioni operative
MicroMAX Pro
User & Maintenance Manual
MAN-MAXPRO
REV. B.0.
OTHER LUMIDOR PRODUCTS
2
Other Lumidor Products Please visit our website at www.lumidor.com for other
products that may be applicable to your needs.
DISCLAIMER
Notwithstanding any stated, written or implied warranty that
may be associated with the sale, purchase, or use of its
products, Lumidor, 11221 Interchange Circle South, Miramar,
Florida, 33025, a subsidiary of Zellweger Analytics, will not be
responsible for any damage or injury resulting to any person or
property that may be construed as resulting from a malfunction
of any of our products if said product has not been operated or
maintained in accordance with our instructions as detailed in
instruction sheets or printed manuals, or if the product has
been tampered with, or serviced by, any other than our factory
or other authorized service agent.
Copyright Lumidor, June 2000.
Printed in U.S.A.
MAN-MAXPRO
REV: B.0
MAN-MAXPRO
REV. B.0.
CAUTIONS AND WARNINGS
3
Cautions and Warnings
WARNING
DO NOT PROCEED BEFORE READING
To ensure proper functioning and use of this product, do
not use this instrument until you read and completely
understand this operating manual. It contains operating
and maintenance procedures to ensure proper instrument
function. For your safety, you are required to calibrate this
instrument periodically. Please refer to the calibration
section of this manual
Substitution of components may impair intrinsic safety.
Use only MPRO-BPR NiMH rechargeable battery pack, or
MPRO-BPA alkaline battery holder with four each of the
following alkaline cells only: Duracell Procell-2400,
Duracell MN-2400, and Eveready E-92 or EN-92. Observe
proper polarity when installing alkaline batteries.
CAUTION
Do not change or charge batteries in a hazardous location.
The LEL (Lower Explosive Level) range of this monitor is
factory calibrated to methane. If monitoring a different
combustible gas, calibrate the combustible gas range of
the monitor to the appropriate gas.
This instrument has not been tested in atmospheres
exceeding 21% oxygen.
Calibration is required when sensors are changed or
added to the instrument.
MAN-MAXPRO
REV. B.0.
CAUTIONS AND WARNINGS
4
WARNING
Use only the approved accessories indicated in this
manual.
Do not connect the instrument to a PC in a potentially
hazardous environment.
AUSTRALIAN OR NEW ZEALAND
CUSTOMERS:
Use only supplied type approved charger when charging
from normal 240VAC outlet in Australia or New Zealand.
MAN-MAXPRO
REV. B.0.
LIFETIME WARRANTY
5
Lifetime Warranty This instrument is warranted, to the original end-user
purchaser, against defects in materials and workmanship for
the life of the product, excluding the battery and pump, which
carry a two year limited warranty. During this period Lumidor
will repair or replace defective parts on an exchange basis,
F.O.B. the factory at Miramar, Florida. The end-user purchaser
will pay freight charges to and from Lumidor. The decision to
repair or replace parts shall be determined by Lumidor.
Sensor Warranties
(1) The oxygen sensor is guaranteed to operate
satisfactorily for two years from the date of sale (i.e. the
date of shipment) and will be replaced at no charge
within that period only if it will not provide a correct
reading after calibration by authorized service
personnel. Physical or chemical damage, resulting from
exposure to improper elements, is not covered.
(2) The combustible sensor is guaranteed to operate
satisfactorily for two years from date of sale (i.e. from
date of shipment). If It will not provide a correct reading
after calibration by authorized service personnel, it will
be replaced at no charge within that period. This
guarantee is void if it has been contaminated by some
unusual substance, including but not limited to, water
and/or other liquids, oily compounds, corrosives,
silicones, lead vapors, extremely high concentrations of
combustible gases, and various particulates which may
inhibit gas flow to the sensor element.
(3) The toxic sensors are guaranteed to operate
satisfactorily for two years (18 months for CL2, CLO2
and HCN sensors, 12 months for the NH3 sensor) from
the date of sale (i.e. the date of shipment). They will be
replaced at no charge within that period only if they will
not provide a correct reading after calibration by
authorized service personnel, and only if the sensor
membranes exhibit no physical or chemical damage
resulting from exposure to improper substances.
MAN-MAXPRO
REV. B.0.
LIFETIME WARRANTY
6
Conditions and Exclusions
To maintain this warranty, purchaser must perform
maintenance and calibration as prescribed in the instrument
operation manual, including prompt replacement or repair of
defective parts and such other necessary calibration,
maintenance and repair as may be required, according to the
use of the instrument, in the reasonable judgment of Lumidor.
Normal wear and tear, and parts damaged by abuse, misuse,
negligence or accidents are specifically excluded from the
warranty.
Purchaser acknowledges that, notwithstanding any contrary
term or provision in the purchaser's purchase order or
otherwise, the only warranty extended by Lumidor is the
express warranty contained herein. Purchaser further
acknowledges that there are no other warranties expressed or
implied, including without limitation, the warranty of
merchantability or fitness for a particular purpose; that there
are no warranties which extend beyond the description of the
face hereof; that no oral warranties, representations, or
guarantees of any kind have been made by Lumidor, its
distributors or the agents of either of them, that in any way alter
the terms of this warranty; that Lumidor and its distributors
shall in no event be liable for any consequential or incidental
damages, including but not limited to injury to the person or
property of the purchaser or others, and from other losses or
expenses incurred by the purchaser arising from the use,
operation, storage or maintenance of the product covered by
the warranty; that Lumidor's liability under this warranty is
restricted to repair or replacement of defective parts at
Lumidor sole option; and that Lumidor neither assumes nor
authorizes any other person to assume for it any other
warranty. The warranty shall be void if serial numbers affixed
to the products are removed, obliterated or defaced.
Lumidor, Miramar, Florida
MAN-MAXPRO
REV. B.0.
TABLE OF CONTENTS
Section Page
7
Table of Contents
1. Preparation for Use 10
1.1 Unpacking 10
1.2 Charging 10
2. General Description 12
3. Features 14
4. Operating Instructions 18
4.1 Turn-on 19
4.2 Standard Mode Sequence 19
4.3 Testing Sensors and Alarms 20
4.4 Continuous Monitoring 22
4.5 Remote Sampling (Pretesting) 22
4.6 Alarms 23
4.7 Clearing Memory 24
4.8 Turn-off 24
5. Calibration 25
5.1 Calibration Frequency 25
5.2 Calibration Procedure (when all calibration
gases are in a single canister) 26
5.3 Calibration Procedure (when not all calibration
gases are in a single canister) 27
5.4 Zeroing 29
6. Programming 30
6.1 Programming Options 30
6.2 Selecting LEL Gas Type 31
6.3 Setting Date Format 32
6.4 Setting Date/Time 33
6.5 Selecting Data Log Frequency 34
6.6 Auto-zeroing 34
6.7 Displaying Last Calibration Date 35
6.8 Selecting Latching/Non-latching Gas Alarms 35
6.9 Setting Calibration Gas Level 36
MAN-MAXPRO
REV. B.0.
TABLE OF CONTENTS
Section Page
8
6.10 Setting High Alarm 37
6.11 Setting Low Alarm 37
6.12 Displaying Calibration Due Date 38
6.13 Choosing a Language 39
6.14 Selecting Immediate Alarm Mode/TWA Alarm
Mode 39
6.15 Restoring Factory Defaults 40
6.16 Calibration in Supervisory Mode 40
7. Data Logging 41
7.1 System Requirements 41
7.2 General Information 41
7.3 Program Installation 41
7.4 Uninstall Procedure 42
7.5 Starting the Program 42
7.6 Downloading Information from the MicroMax Pro 43
7.7 Displaying and Printing Data 45
7.7.1 Main Screen 45
7.7.2 Graph Screen 47
7.7.3 Current Calibration Records 49
7.7.4 Calibration History 51
7.7.5 Instrument Parameters 53
7.8 Editing Location 59
7.9 Editing Note 59
7.10 Uploading Information to the MicroMax Pro 59
7.11 Importing Files 60
7.12 Archiving Data 61
7.13 Recovering Data 62
7.14 Getting Help 63
7.14.1 Using MaxPro Log Help 63
7.14.2 Lumidor on the Web 63
7.14.3 Customer Support 63
7.14.4 MaxPro Log Version and Copyright 63
8. Maintenance 64
8.1 Battery Installation 64
MAN-MAXPRO
REV. B.0.
TABLE OF CONTENTS
Section Page
9
8.2 Alkaline Battery Pack Installation 64
8.3 NiMH Battery Pack Installation 65
8.4 NiMH Battery Pack – General Information 66
8.5 Sensor Replacement 66
8.6 Removing and Adding a Sensor 67
8.7 Cleaning 67
8.8 Pump Inlet Filter Replacement 67
8.9 Sampling Hose Maintenance 68
8.10 Storage 68
8.11 Sensor and Battery Disposal 68
9. TroubleShooting 70
9.1 Sensor Not Recognized (“XXX” Displayed) 70
9.2 “LEL FAIL” Message 70
9.3 Low Flow Alarm When Sampling Hose Attached 71
9.4 “Calibration Fail” Message 71
9.5 Instrument Will Not Turn On 71
9.6 Instrument is in Diffusion Mode but Pump
ComesOnWhenCalibrating 71
Appendix A Specifications 72
Appendix B Turn-on Sequence 84
Appendix C Mode Sequence, Standard Mode 87
Appendix D Mode Sequence, User Set-up Mode 88
Appendix E Alarm Modes 92
Appendix F Charging Screens 94
Appendix G Calibration Kits 95
Appendix H Optional Accessories 96
Appendix I Replacement Parts 97
Appendix J Calibrating with Multiple Canisters 99
Appendix K Calibration Gases 101
MAN-MAXPRO
REV. B.0.
1. PREPARATION FOR USE
10
1. PREPARATION FOR USE
1.1 UNPACKING
Check for these items:
•Packaging (retain for possible future use)
•Instrument with internal rechargeable battery pack
•Calibration certificate
•Standard accessories:
–AC battery charger
–Alkaline battery holder
–Dust filter
–10-foot sampling hose with filter and water trap
–Rubber boot with belt clip and neck strap
–Instruction manual
1.2 CHARGING
CAUTION
Do not change or charge batteries in a hazardous location.
Do not try to turn on or otherwise operate this instrument
until it is fully charged.
Use only the MPRO-1 A.C.charger, the MPRO-2 220 volt
AC charger, or the MPRO-6 vehicular charger. Use of any
other charger may cause permanent instrument damage
and will void any warranties. The charge period is
dependent on the condition of the batteries, but should not
exceed about 4 hours for a completely depleted battery
pack. Partially depleted packs will be charged in a much
shorter period of time.
Indice
Altri manuali Honeywell Strumento di misura
Honeywell
Honeywell C7355B Manuale utente
Honeywell
Honeywell BENDIX/KING KRA 405 Manuale utente
Honeywell
Honeywell AD1200-CT Manuale utente
Honeywell
Honeywell SLN 700 Manuale di istruzioni
Honeywell
Honeywell A700 Manuale utente
Honeywell
Honeywell SX Manuale utente
Honeywell
Honeywell W8710A Manuale utente
Honeywell
Honeywell Minitrend QX Manuale utente
Honeywell
Honeywell RAE Systems NeutronRAE II Manuale utente
Honeywell
Honeywell QX Series Manuale utente
Honeywell
Honeywell HEN04112 Manuale utente
Honeywell
Honeywell ACM 150 Manuale del proprietario
Honeywell
Honeywell AutoSet 1500 Manuale utente
Honeywell
Honeywell SEARCHLINE EXCEL PLUS Manuale utente
Honeywell
Honeywell Vertex M Nota di rilascio
Honeywell
Honeywell VERSAFLOW SONIC 2000 Supplemento
Honeywell
Honeywell TWM 9000 Schema elettrico
Honeywell
Honeywell RM640 Manuale utente
Honeywell
Honeywell Q209E Modutrol IV Manuale utente
Honeywell
Honeywell AC-250NXS Manuale utente
