Honeywell 5878 Manuale utente

K14395 6/06 Rev. A

5878

Wireless Wall Transmitter

USER GUIDE

GENERAL INFORMATION

The 5878 is a compact, 6-button wall-mounted

wireless transmitter that permits an alarm system

or home automation devices to be controlled

remotely. The transmitter is typically used for

security system arming and panic and controlling

output relay operations associated with home

automation devices. Check with your installer for

operation of the buttons on your unit.

OPERATING THE BUTTONS

To activate a programmed function, press and hold

the associated button(s) down. The LED will flash

green to indicate the unit has transmitted in

Standard mode, or red to indicate it has transmitted

in High-Security mode.

In order to minimize the possibility of

accidental transmissions, the buttons on

the 5878 must be pressed and held for at

least 1/2 second to activate the

transmitter.

5878-004-V0

LED

STAY

AWAY

Figure 1 - 5878 Transmitter

Table 1 - Transmitter Functions

(Complete this table with your installer)

Button Function

LOW BATTERY INDICATION

When a Button is pressed and a Low Battery

condition exists, a message is transmitted to the

control panel and LOW BAT will be displayed on

the keypad. The LED will not flash during

transmission if the battery is low.

Replacing the Battery

1. Slide out the battery tray located at the bottom

of the 5878.

2. Carefully remove the battery.

3. Press and hold any button for at least one

second.

4. Insert a new battery in case back location as

shown in Figure 2. Positive (+) end must face

up. Use Maxell CR2032, Duracell DL 20325, or

Varta CR2032 lithium battery only.

5. Slide the battery back into the 5878.

6. Press any button and verify that the LED

flashes.

Improper installation will result in

damage to the transmitter.

BATTERY

AWAY STAY

NOTE

POSITIVE (+) SIDE

MUST FACE UP

5878-002-V0

Figure 2 - Replacing the Battery

LIMITATIONS STATEMENT

Signals sent by wireless transmitters may be blocked or reflected by metal objects before they reach the alarm receiver.

Even if the signal path has been recently checked during a weekly test, blockage can occur if a metal object somehow

blocks the signal path.

Wireless button type transmitters that have visual and audible indications of status must be used to confirm that the

desired action (such as arming) has occurred after pressing a function button on any of these transmitters. Be sure to

listen for appropriate audible and visual indications that such action has occurred. Otherwise, you could inadvertently

leave yourself or your premises unprotected.

External factors such as humidity, high or low temperatures, or constant activation of a programmed button may

reduce battery life in a given installation. If the button unit is used infrequently, activate it regularly (once per week)

to confirm operation. A button type transmitter will report a low battery condition to the alarm control when a low

battery status is detected.

FOR WARRANTY INFORMATION AND FOR DETAILS REGARDING THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM,

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE RECEIVER/CONTROL WITH WHICH THIS DEVICE IS USED.

FCC AND INDUSTRY CANADA STATEMENT

THIS DEVICE COMPLIES WITH PART 15 OF FCC RULES AND RSS210 OF INDUSTRY CANADA. OPERATION IS SUBJECT

TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS

DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

THE USER SHALL NOT MAKE ANY CHANGES OR MODIFICATIONS TO THE EQUIPMENT UNLESS AUTHORIZED BY THE

INSTALLATION AND SETUP GUIDE OR THE USER GUIDE.

12800 Brookprinter Place,Poway, CA 92064

www.honeywell.com/security

‡K14395TŠ

‡K14395TŠ‡K14395TŠ

‡K14395TŠ

K14395 6/06 Rev. A

Altri manuali Honeywell Telecomando

Honeywell

Honeywell 42136 Manuale utente

Honeywell

Honeywell 5804BD Manuale utente

Honeywell

Honeywell TS607 Manuale utente

Honeywell

Honeywell ADEMCO 5804BDV-CN Manuale utente

Honeywell

Honeywell Hometronic HRD 20 Manuale di istruzioni

Honeywell

Honeywell FocusPRO 6000 Series Manuale utente

Honeywell

Honeywell ADEMCO 5804BDV Manuale utente

Honeywell

Honeywell Wireless Remote Control Manuale utente

Honeywell

Honeywell HS3FOB1N Manuale utente

Honeywell

Honeywell 5834-4 Istruzioni operative

Honeywell

Honeywell EXCEL 5000 OPEN ZAPP Manuale utente

Honeywell

Honeywell ADEMCO 5804BDV Manuale utente

Honeywell

Honeywell 40015 Manuale utente

Honeywell

Honeywell REM5000R01 Manuale utente

Honeywell

Honeywell DG115EZIAQ - TrueIAQ Digital IAQ Control Manuale utente

Honeywell

Honeywell TFU 22 Manuale utente

Honeywell

Honeywell REDLINK ERM5220R Manuale utente

Honeywell

Honeywell DF-RC Manuale utente

Honeywell

Honeywell YTH5320R Manuale utente

Honeywell

Honeywell Silent Knight 6860 Manuale tecnico

Honeywell

Honeywell HCW 23 Manuale utente

Honeywell

Honeywell SILENT KNIGHT RA-2000 Manuale utente

Honeywell

Honeywell ADEMCO 5804BDV Manuale utente

Honeywell

Honeywell ADEMCO 5804BD Manuale utente

Manuali Telecomando popolari di altre marche

Panasonic

Panasonic EUR7622KB0 Manuale utente

Bang & Olufsen

Bang & Olufsen Beo4 Manuale utente

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuale utente

Multiplex

Multiplex PROFI TX 9 Manuale utente

One Remote

One Remote RMB4 Manuale utente

FUTABA

FUTABA 9ZAP - PART2 Manuale utente

HR Matic

HR Matic HR MULTI 3 Manuale utente

Yamaha

Yamaha ACC-GNRST-30-20 Manuale utente

EisSound

EisSound KBSOUND Manuale utente

Marantz

Marantz RC101 Manuale utente

Conrad

Conrad FS20 TC6 Manuale utente

Anritsu

Anritsu MP1777A Manuale utente

Niles

Niles WVC100 Guida alla risoluzione dei problemi

RCA

RCA RCU1300 Manuale utente

Bang & Olufsen

Bang & Olufsen BEO6 Manuale utente

GE 94901 Manuale utente

Onbon

Onbon YQ1-75 Manuale utente

FUTABA

FUTABA R7108SB Istruzioni per l'installazione