HP 3C509B-TP Manuale utente

Etherlink IIIB ISA Network

Interface Card (10BT)

3C509B-TP

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this material,

including, but not limited to, the implied warranties of merchantability and

fitness for a particular purpose.

Hewlett-Packard shall not be liable for errors contained herein or for incidental

or consequential damages in connection with the furnishing, performance, or use

of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its

software on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent

of Hewlett-Packard Company.

Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft

Corporation.

MMXTM is a trademark of Intel Corporation.

Pentium® is a registered trademark of Intel Corporation.

Hewlett-Packard France

Commercial Desktop Computing Division

38053 Grenoble Cedex 9

France

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

1 Connecting to a Netware 3.12 Server

Windows for

Workgroups

Requirements

• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.

DOS ODI - File Name: 3C5X9.COM Size: 42KB Date: 7/21/96

• DOS and MS-Windows for Workgroups 3.11 media.

• Novell Netware server 3.12 that supports Net BEUI, NWLink IPX/SPX,

and NWLink NetBIOS transfer protocols.

• Netware client for DOS and MS-Windows.

Device Configuration

• Boot PROM Disabled

• Transceiver Type Auto Select

• Network Driver Optimization Windows or OS/2 Client

• Maximum Modem Speed 9600 Bps

• Plug and Play Compatibility Disabled

• Full Duplex Disabled

Procedure

1With the HP Vectra turned off install the 3COM Etherlink III 3C509-B

adapter card into an ISA slot.

2Power on the machine and allow it to boot to a DOS prompt.

3Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s

website) and execute 3C5X9CFG.EXE.

Vectra VL8 Vectra VL7 Vectra VE7/VE8

I/O Base Address 210 210 300

Interrupt Request

Level

10 10 10

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

4Select “CONFIGURE NIC,” and verify the resource settings listed above

under the heading “Device Configuration.”

5If changes are required, save those changes and exit.

6Remove the 3com cards driver diskette and insert Netware client for DOS

and MS-Windows disk 1.

7Execute INST_DOS.EXE and enter yes to accept the agreement if you are

using a Vectra VL8, then go directly to step 8.

If you are using a Vectra VL7 or VE7/VE8, complete the installation by

following the steps below.

ASpecify the settings as listed below:

• C:\NWCLIENT

• Yes

• C:\WINDOWS

• No

• 3Com Fast Etherlink/Etherlink III Bus Master2.

bUnder the heading "Select the driver for your network board", insert

the 3Com 3C590 drivers disk and set the path to "A:\NETWARE\CLI-

ENT." (If you have an HP preloaded HDD, set path to "C:\Masters\Lan-

Drv\3C509\NWCLIENT\)

cPress "Enter" to continue the installation.

dWhen prompted, insert the corresponding disks to complete file

transfer and driver installation.

eWhen the install utility is finished, press <CRTL><ALT><DEL> to

restart the machine.

fAfter Windows loads, open the "NETWORK" folder, double-click the

"NETWORK SETUP" icon.

gSelect "Networks", and verify that "Novell Netware (Workstation Shell

4.0 and above)" is listed under "Install Windows support for the

following network only:" and click on "OK."

8Accept the default products by pressing enter, and then press “F10” to

continue.

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

9Select 16-bit LAN Drivers and hit the enter key.

10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER”

and hit enter.

11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the

path to “A:\NWCLIENT\” and press enter.

12 Select “3Com Etherlink III Parallel Tasking Family” and press enter.

13 Accept the default settings, press “F10” to continue, and verify the

following entries for the “Installation Configuration Summary”:

❒YES

❒C:\NOVELL\CLIENT32

❒C:\WINDOWS

❒16-bit LAN drivers

❒3Com Etherlink III Parallel Tasking Family

14 Press “F10” to save and continue.

15 When prompted, insert the corresponding disks to complete file transfer

and driver installation.

16 When the install utility is finished, press <CRTL><ALT><DEL> to restart

the machine.

17 After windows loads, open the “NETWORK” folder, double-click the

“NETWORK SETUP” icon.

18 Select “Networks”, and verify that “Novell Netware (Workstation Shell 4.0

and above)” is listed under “Install Windows support for the following

network only:” and click on “OK.”

1 Connecting to a Netware 3.12 Server

Windows for Workgroups

1 Connecting to a Netware 3.12 Server

Windows 95 SR2

Windows 95 SR2 Requirements

• HP Vectra with Windows 95 SR2 installed.

• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.

• Vectra VL8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97

• Vectra VL7 Driver Name: Elnk.VXD Size: 30KB Date: 7/18/96

• Vectra VE7/VE8 Driver Name: W95EL5X9.INF Size: 16KB Date: 6/11/97

• Windows 95 SR2 media.

• Novell Netrware 3.12 server that supports Net BEUI, NWLink IPX/SPX,

and NWLink NetBIOS transfer protocols.

Device Configuration

• Boot PROM Disabled

• Transceiver Type Auto Select

• Network Driver Optimization Windows or OS/2 Client

• Maximum Modem Speed 9600 Bps

• Plug and Play Compatibility Disabled

• Full Duplex Disabled

Procedure

1With the HP Vectra turned off install the 3COM Etherlink III 3C509-B

adapter card into an ISA slot.

2Power on the machine and restart Windows 95 SR2 in MS-DOS Mode.

3Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s

website) and execute 3C5X9CFG.EXE.

4Select “CONFIGURE NIC,” and verify the resource settings listed above

under the heading “Device Configuration.”

Vectra VL8 Vectra VL7 Vectra VE7/VE8

I/O Base Address 210 210 300

Interrupt Request

Level

10 10 10

1 Connecting to a Netware 3.12 Server

Windows 95 SR2

5If changes are required, save those changes and exit.

6Remove the 3com cards driver diskette and restart the machine.

7After windows loads, click on “Start,” to “Settings” and over to “Control

Panel.”

8Double click on “Network” and select “Add.”

9Choose to add an adapter, click on “Add” then on “Have Disk.”

10 Insert the 3C509B drivers diskette and set path to “A:\” and hit enter.

(If you have a Hewlett-Packard pre-loaded HDD, set the path statement

to “C:MASTERS\LANDRV\3C509B\”)

11 High light the adapter labeled “3Com Etherlink III ISA (3C509/3C509B) in

ISA Mode” and press “OK.”

12 At the “Network” dialogue box, click on the “Identification” folder.

13 Enter your “Computer Name,” “Workgroup,” and “Computer

Description.”

(If you do not have a Computer name, Workgroup name and Computer

description, contact your network administrator)

14 Approve the “Basic Configuration Resources” by clicking on “OK.”

15 When prompted, set the path to your Windows 95 SR2 files and click on

“OK.”

16 Click on “YES” to complete installation and restart the machine.

2 Connecting to a Netware 4.11 Server

Windows for Workgroups

2 Connecting to a Netware 4.11 Server

Windows for

Workgroups

Requirements

• HP Vectra with DOS and MS-Windows for Workgroups 3.11 installed.

• 3COM Etherlink 3C509-B ethernet card and drivers disk ver. 5.0.

DOS ODI - File Name: 3C5X9.COM Size: 42KB Date: 7/21/96

• DOS and MS-Windows for Workgroups 3.11 media.

• Novell Netware server 4.11 that supports Net BEUI, NWLink IPX/SPX,

and NWLink NetBIOS transfer protocols.

• Netware client for DOS and MS-Windows.

Device Configuration

• I/O Base Address 300

• Interrupt Request Level 10

• Boot PROM Disabled

• Transceiver Type Auto Select

• Network Driver Optimization Windows or OS/2 Client

• Maximum Modem Speed 9600 Bps

• Plug and Play Compatibility Disabled

• Full Duplex Disabled

Procedure

1With the HP Vectra turned off install the 3COM Etherlink III 3C509-B

adapter card into an ISA slot.

2Power on the machine and allow it to boot to a DOS prompt.

3Insert the 3COM drivers diskette (ver. 5.0 downloaded from 3COM’s

website) and execute 3C5X9CFG.EXE.

4Select “CONFIGURE NIC,” and verify the resource settings listed above

under the heading “Device Configuration.”

5If changes are required, save those changes and exit.

2 Connecting to a Netware 4.11 Server

Windows for Workgroups

6Remove the 3COM cards driver diskette and insert Netware client for DOS

and MS-Windows disk 1.

If you are using a Vectra VL8, go straight to step 7.

If you are using a VL7 or VE7/VE8, finish the installation by using the

instructions below.

aExecute INSTSTALL.EXE.

bSpecify the settings as listed below:

• C:\NWCLIENT

•Yes

• C:\WINDOWS

•No

• 3Com Fast Etherlink/Etherlink III Bus Master for VE7/VE8, (or

3COM Etherlink III Parallel Tasking Family for VL7, then highlight

option 6 and then go to step e below).

cUnder the heading "Select the driver for your network board", insert

the 3Com 3C590 drivers disk and set the path to "A:\NETWARE\

CLIENT." (If you have an HP preloaded HDD, set path to "C:\

Masters\LanDrv\3C509\NWCLIENT\)

dPress "Enter" to continue the installation.

eWhen prompted, insert the corresponding disks to complete file

transfer and driver installation.

fWhen the install utility is finished, press <CRTL><ALT><DEL> to

restart the machine.

gAfter Windows loads, open the "NETWORK" folder, double-click the

"NETWORK SETUP" icon.

hSelect "Networks", and verify that "Novell Netware (Workstation Shell

4.0 and above)" is listed under "Install Windows support for the follow-

ing network only:" and click on "OK."

7Execute INST_DOS.EXE and enter yes to accept the agreement.

8Accept the default products by pressing enter, and then press “F10” to

continue.

9Select 16-bit LAN Drivers and hit the enter key.

Questo manuale è adatto per i seguenti modelli

Manuali Scheda di rete popolari di altre marche

FirstComm

FirstComm OBiWiFi5G Manuale utente

Sun Microsystems

Sun Microsystems Interface Adapter Manuale utente

TRENDnet

TRENDnet TU2-ETG Manuale utente

YASKAWA

YASKAWA SI-EN3 Manuale utente

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuale utente

Belkin

Belkin F5D7050 Manuale utente

3Com

3Com EtherLink 3C509B Manuale utente

TRENDnet

TRENDnet TEG-PCITX Manuale utente

Cisco

Cisco MC16E Manuale utente

Delta Electronics

Delta Electronics Braking Modules VFDB Series Manuale utente

TwinMOS

TwinMOS Booming Manuale utente

Dialogic

Dialogic Media Board DM/V1200BTEPEQ Manuale utente

Buffalo

Buffalo AirStation WLI-PCM-L11GP Manuale utente

National Instruments

National Instruments NI 9234 Manuale utente

Hama

Hama 49276 Manuale utente

Linksys

Linksys WCF54G - Wireless-G Compact Flash Card Manuale operativo

Compaq

Compaq Wireless LAN 100 Manuale utente

Bose

Bose PowerMatch Dante Manuale utente