HP NetServer e 800 Manuale utente

HP Part Number D9394-90000

Printed June 2000

HP NetServer E 800

Installation Guide

Notice

The information contained in this document is subject to change without notice.

Hewlett-Packard makes no warranty of any kind with regard to this

material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Hewlett-Packard shall

not be liable for errors contained herein or for incidental or consequential

damages in connection with the furnishing, performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or reliability of its software

on equipment that is not furnished by Hewlett-Packard.

This document contains proprietary information that is protected by copyright.

All rights are reserved. No part of this document may be photocopied,

reproduced, or translated to another language without the prior written consent of

Hewlett-Packard Company.

Intel®and Pentium®are registered trademarks of Intel Corporation. Microsoft®,

Windows NT®, Windows 95®and Windows 2000®are registered trademarks of

Microsoft in the U.S. and other countries. Novell®and NetWare®are registered

trademarks of Novell, Incorporated in the U.S. and other countries. Symantec®is a

registered trademark of Symantec, Incorporated. pcANYWHERE32™ is a trademark

of Symantec, Incorporated. Torx®is a registered trademark of CamCar/Textron,

Incorporated.

Hewlett-Packard Company

Network Server Division

Technical Communications / MS 45SLE

10955 Tantau Avenue

Cupertino, California 95014 USA

Audience Assumptions

This guide is for the person who installs, administers, and troubleshoots LAN

servers. Hewlett-Packard Company assumes you are qualified in the servicing of

computer equipment and trained in recognizing hazards in products with

hazardous energy levels.

iii

Contents

Setting Up the HP NetServer E 800................................................................. 1

Introduction ................................................................................................... 1

Step 1: Attaching all the Cables................................................................. 2

Step 2: Opening the HP NetServer............................................................ 3

Step 3: Installing Memory.......................................................................... 5

Step 4: Installing Mass Storage Devices.................................................... 6

Step 5: Installing Adapter Boards............................................................. 10

Step 6: Installing a Second Processor ..................................................... 14

Step 7: Configuring the HP NetServer..................................................... 19

Setting Up the HP NetServer E 800

Introduction

This installation guide is a quick reference for HP NetServer E 800 installation.

Skip any steps that do not apply to your installation. Refer to the figures below

for connection and operating information. For more information, refer to the

HP NetServer E 800 User Guide.

Flexible

Disk Drive

CD-ROM Drive

Power ON/OFF/

Sleep Switch

Power ON/

OFF/Sleep LED

SCSI Drive

Activity LED

Optional Back-Up

Tape Drive

Power

Mouse

Keyboard

USB(2) LAN

Serial A

Parallel

Serial B

Video

(SVGA)

Key Lock

External SCSI

(Optional)

Fold-Out

Feet (4)

Unlocked Position

Locked Position

Setting Up the HP NetServer E 800

Step 1: Attaching all the Cables

If you are not installing any accessories, attach all available cables to the

respective connectors, then go to "Step 7: Configuring the HP NetServer."

NOTE The two USB connectors are reserved for printers, scanners,

and external modems. The NetServer does not support USB

connections for the keyboard and mouse.

Power

Power Cord

Strain Relief

Mouse

Keyboard

Video

SVGA

LAN

Setting Up the HP NetServer E 800

Step 2: Opening the HP NetServer

Tools Required:

•¼ inch flat-blade screwdriver

•Torx T-15 driver

WARNING Before removing the cover, always disconnect the power cord

and remove the telephone cable.

Disconnect the power cord to avoid exposure to high energy

levels that may cause burns when parts are short-circuited by

metal objects such as tools or jewelry. Disconnect telephone

cables to avoid exposure to shock hazard from telephone

ringing voltages.

Key-

Lock

Slotted

Thumbscrews(6)

Setting Up the HP NetServer E 800

Front of Chassis

Bottom of Chassis

Cover

Latch Opening

Air Duct

Latch

Setting Up the HP NetServer E 800

Step 3: Installing Memory

•Use only HP DIMMs, which are 3.3V, 168-pin, PC133 (133 MHz),

buffered SDRAM DIMMs in 128 MB, 256 MB, or 512 MB.

•DIMMs may be installed in any slot, in any combination (sizes mixed), in

any order, but HP recommends starting at slot 0 and filling the slots in

order with the largest size first: 0, 1, 2, and 3.

•Ensure both latches close on the DIMM when completely installed.

System Board

0123

Retaining Latches

DIMM Slot

Keys

Notches

Setting Up the HP NetServer E 800

Step 4: Installing Mass Storage Devices

•The NetServer is internally limited to 7 mass storage shelves.

The flexible disk drive and CD-ROM drive, which are standard on all

models of the HP NetServer E 800, occupy shelves 1 and 2 respectively.

•If a backup tape drive is used, it will occupy shelf 3.

•Shelves 4, 5, 6, and 7 are available for up to four SCSI hard drives and at

least one is required for the boot drive.

•IDE drives are not supported in this NetServer.

CAUTION Do not connect high voltage differential (HVD) SCSI devices

on the SCSI bus or you will damage the other devices.

1. Remove the Drive Cage by loosening the three captive screws.

Top of Chassis (Side view)

Captive Screws (3)

Front of

HP NetServer

Hard Disk

Drive Cage

(removable)

Shelf 1

Shelf 2

Shelf 3

Shelves 4-7 (4)

2. Install the SCSI hard disk drive.

Altri manuali per NetServer e 800

Indice

Altri manuali HP Server

HP StorageWorks P4000 Series Manuale di istruzioni

HP ProLiant BL460C Generation 8 Manuale utente

HP SimpliVity 380 Gen9 Manuale del prodotto

HP ProLiant BL620c Generation 7 (G7) Istruzioni utente

HP ProLiant DL120 Gen9 Manuale

HP ProLiant SL2x170z - G6 Server Manuale

HP ProLiant BL420c Manuale utente

HP 30292B Manuale utente

HP Integrity rx2660 Manuale utente

HP Compaq t1010 Manuale utente

HP ProLiant DL180 Generation 6 (G6) Istruzioni utente

HP t310 G2 Istruzioni per l'installazione

HP t5300 - Thin Client Manuale utente

HP ProLiant ML110 Istruzioni utente

HP ProLiant SL160z Generation 6 (G6) Guida all'installazione

HP 9000 rp7420 Manuale utente

HP BCDVideo BCD108 Manuale utente

HP D7171A - NetServer - LPr Manuale utente

HP D7171A - NetServer - LPr Manuale operativo e di manutenzione

HP 2533t - Compaq Mobile Thin Client Manuale utente

HP D5970A - NetServer - LCII Manuale utente

HP ProLiant DL380 Generation 5 Manuale utente

HP ProLiant DL380p Manuale utente

HP ProLiant DL180 G Manuale

Manuali Server popolari di altre marche

Dell

Dell PowerEdge R410 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

Dell

Dell PowerEdge XE9640 Manuale

Dell

Dell PS4100 Istruzioni di montaggio

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

Dell

Dell PowerEdge 3YPMN Manuale utente

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

Milestone

Milestone Husky IVO 350T Manuale utente

Planet

Planet NAS-7410 Manuale utente

Lenovo

Lenovo ThinkSystem SR635 V3 Manuale utente

Dell

Dell PowerEdge HS5610 Manuale