Huawei ESight V300R005C00 Manuale

HUAWEI TECHNOLOGIES Co., Ltd.

eSight

V300R005C00

Hardware Installation Guide

Issue: 01

Date: 2015-12-30

Installation Process

Preparation for

Installation

Installing the Server

Installing the Power

Cables

Installing the Signal

Cables

Checking the

Installation

Powering On/Off the

Server

End

Start

Page 2 to 3

Page 4 to 5

Page 6 to 7

Page 8 to 12

Page 13

Page 14

2015

Preparation for Installation

Notice

This document describes how to install the server, how to connect the power cables and signal cables, and

how to check the connections when the Huawei RH2288H V3, and RH5885H V3 server act as the server of

eSight.

The power cable connection and signal cable connection that are detailed in this document are written

according to the standard configuration. If the actual on-site installation requirements are inconsistent with this

document, handle the requirements according to the actual situation. Unless otherwise specified, the models of

the corresponding floating nuts and panel screws are M6.

All figures in this manual are for reference only and may differ from actual devices which prevail.

This document does not describe the installation of the cabinet. For details on the cabinet installation, refer to

the installation guide of the cabinet.

Before installing devices in the cabinet, take appropriate antistatic measures to prevent any electrostatic discharge of the

human body from damaging sensitive components.

Do not install or remove a live power cable. Before installing or removing the power cable, turn off the power switch.

Server Specifications and Installation Requirements

•Cabinets are 19-inch-wide and 39.37-inch-deep and comply with International Electrotechnical Commission

(IEC) 297 standards.

•A space of at least 800 mm be reserved in front of and at the back of each cabinet respectively to facilitate

ventilation and maintenance.

The following table lists the basic server specifications. For details about server specifications, see the server

specifications delivered with devices.

The preceding servers can be installed in the following cabinets:

To ensure a low center of gravity and high stability, install servers in the lower part of a cabinet.

Server Dimensions

(H x W x D) (mm) Weight (kg) Input voltage (V) Rated Power (W)

RH2288H V3 86.1 (2U) x 447 x 708 27 100 V AC to 240 V AC 2 x 460

RH5885H V3 175 (4U) x 447 x 790 62 100 V AC to 240 V AC 2 x 2000

–48 V DC to –60 V DC 2 x 2500

Tools

Measuring Tape

Phillips Screwdriver Flat-head Screwdriver Mount Bar

Tie Wrap

Wire Stripper Diagonal Pliers RJ45 Crimping Tool

Multimeter Network Cable Tester

ESD Gloves ESD Wrist Strap

The tools for installation are not delivered along with the device. Please provide for yourself.

Installing the Server

1 Installing the Server on Adjustable Guide Rails

(Applies to All Cabinets)

•Each server must be supported by guide rails. Stacking one server on another will cause server damage.

•Guide rails are divided into left and right guide rails (labeled with L and R). A pair of guide rails should be installed

together and cannot be installed reversely.

You can install the server to different cabinets by adjusting the length of guide rails:

• RH2288H V3 server: distance between front and rear mounting rails: 543.5-848.5 mm

• RH5885H V3 server: distance between front and rear mounting rails: 550-860 mm

The following tools are required during the installation:

• M3-M6 Phillips screwdriver

•Electrostatic discharge (ESD) gloves

Install adjustable guide rails by referring to the installation guide.

At least two persons lift the server on two sides and move it to the cabinet. Place the server on the guide

rails and push it in to the cabinet.

•The server is heavy, and two or three persons are required to carry the PC server.

•If disks are removed before transportation, record the slot of each disk, and install the disks after installing the

server. Otherwise, the system with pre-installed operating system may fail to start.

•When pushing the server into a cabinet, adjust the server location behind the cabinet to prevent the server from

hitting mounting bars.

When the two mounting ears on the server contact the mounting bards of the cabinet, tighten the captive

screws on the mounting ears to secure the server.

Installing the Server on L-shaped Guide Rails

(Applies Only to a Huawei Cabinet)

a. Fasten one end of a floating nut to the installation hole in a

guide rail at the front of the rack.

b. Fasten the upper end of the floating nut to the mounting bar at

the front of the rack by using the floating nut mounting bar.

a. Place a guide rail horizontally in the planned position and keep

the guide rail contact with the mounting bars in the rack.

b. Tighten the screws.

c. Install another guide rail on the opposite side by using the same

method.

The following tools are required during the installation:

•M3-M6 Phillips screwdriver

•Floating nut mounting bar

•Electrostatic discharge (ESD) gloves

•Each server must be supported by guide rails. Stacking one server on another will cause server damage.

•L-shaped guide rails can only be used in a Huawei cabinet. L-shaped guide rails are delivered with Huawei racks. No

L-shaped guide rails are delivered with the server.

Install floating nuts.

Install L-shaped guide rails.

Floating nuts provide tapped holes for the M6 screws used to secure a server.

At least two persons lift the server on two sides and move it to the

cabinet. Place the server on the guide rails and push it in to the

cabinet.

•The server is heavy, and two or three persons are required to carry the PC

server.

•If disks are removed before transportation, record the slot of each disk,

and install the disks after installing the server. Otherwise, the system with

pre-installed operating system may fail to start.

•When pushing the server into a cabinet, adjust the server location behind

the cabinet to prevent the server from hitting mounting bars.

4 When the two mounting ears on the server contact the mounting bards of the cabinet, tighten the captive

screws on the mounting ears to secure the server.

Installing the Power Cables

Connecting an AC Power Cable

•Do not connect the power cables when the power-supply device is powered on. Instead, switch off the power-supply

device to avoid injuries.

•To protect devices and personnel, use the matching power cables.

Connect the one end of the AC power cable

to the power port on the PSU of server.

Insert the other end of the AC power cable

into the AC power socket on the rack. The

AC power socket is horizontally secured on

the rear of the rack. Select the jacks on the

nearest socket for connection based on the

installation plan.

Bind the power cable to the cable trough

using cable ties.

Connecting a DC Power Cable (RH5885H V3 Server)

Do not connect the power cables when the power-supply device is powered on. Instead, switch off the power-supply

device to avoid injuries.

a. Use a Phillips screwdriver to loosen the screw

in the ground hole on the rear of the server, and

connect one end of the ground cable to the

removed screw. Install the screw in the ground

hole and tighten the screw.

b. Use a Phillips screwdriver to loosen the screw

on the ground bar in the rack and connect the

other end of the ground cable to the removed

screw. You are advised to choose the screw

nearest to the server. Install the screw in the

ground bar and tighten the screw.

Connect the OT terminal of the negative electrode

to the terminal NEG(-) of the PSU, and connect

the OT terminal of the positive electrode to the

terminal RTN(+) of the PSU. Then tighten the

screws.

Install the protective cover for the PSU,

and tighten the screws to secure the

protective cover.

Connect the ground cable.

Bind the power cable to the cable trough

using cable ties.

Installing the Signal Cables

1 Interfaces of the RH2288/RH5885 Server

The position of each interface on the preceding devices varies with actual devices. The pictures in this document are

referential to describe the installation procedure of the device. If the pictures are different from the delivered devices, take

the delivered devices as the standard. For details about the devices, see the associated manuals delivered with the devices.

RH5885H V3 server (rear view)

Number Port Description

1 GE port Connects the service network.

2 Mgmt management network port Connects the maintenance network.

3 VGA port Connects a display.

4 USB Port Connects the mouse, keyboard, and

other devices.

RH2288H V3 server (rear view)

Single-Node System Network Cable Connection

•Connect network ports of the server to the switch based on the actual networking. In a single-node system, connect

at least one network port.

•To remotely manage the server, connect the Mgmt management port of the server to the switch.

RH2288H V3

RH5885H V3

Indice

Altri manuali Huawei Server

Huawei

Huawei U-SYS MRS6100 Manuale utente

Huawei

Huawei FusionModule2000 V500R003C10 Manuale utente

Huawei

Huawei FusionServer Pro 5885H V5 Guida di riferimento rapido

Huawei

Huawei X6000 Manuale utente

Huawei

Huawei TaiShan Istruzioni operative

Huawei

Huawei FusionModule800 Manuale utente

Huawei

Huawei TaiShan 200 2280 Manuale

Huawei

Huawei UPS5000-E-****-FM series Manuale utente

Huawei

Huawei TaiShan 200 Manuale utente

Huawei

Huawei NetCol5000-A-035 Manuale utente

Huawei

Huawei E9000 Istruzioni operative

Huawei

Huawei FusionModule500 Manuale utente

Huawei

Huawei TaiShan 200 Series Manuale utente

Huawei

Huawei PDU8000 Series Manuale utente

Huawei

Huawei RH8100 V3 Manuale utente

Huawei

Huawei FusionServer Pro XH628 V5 Server Node Guida di riferimento rapido

Huawei

Huawei RTN 905 V100 Manuale utente

Huawei

Huawei FusionServer Pro 2488 V5 Guida di riferimento rapido

Huawei

Huawei FusionModule2000 V500R003C10 Manuale utente

Huawei

Huawei Tecal RH2285 Manuale utente

Huawei

Huawei FusionServer RH2288H V3 Manuale utente

Huawei

Huawei VP9660 Manuale utente

Huawei

Huawei E9000 Manuale utente

Huawei

Huawei 5288 V3 V100R003 Manuale utente

Manuali Server popolari di altre marche

HP AlphaServer ES47 Manuale utente

Dell

Dell PowerEdge R410 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

Dell

Dell PowerEdge XE9640 Manuale

Dell

Dell PS4100 Istruzioni di montaggio

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

HP ProLiant Gen9 Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

Dell

Dell PowerEdge 3YPMN Manuale utente

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

HP Integrity rx2600 Guida all'installazione

Milestone

Milestone Husky IVO 350T Manuale utente

Huawei eSight V300R005C00 Manuale

Manuali Server popolari di altre marche