IBM I Series Manuale utente

iSeries

820, 825, 5075, 5095 and 0595

Power Supply and Air Moving Device

Version 5



iSeries

820, 825, 5075, 5095 and 0595

Power Supply and Air Moving Device

Version 5



Note

Before using this information and the product it supports, be sure to read the information in

“Notices,” on page 31.

Fourth Edition (August 2005)

This edition applies to version 5, release 3, modification 0of IBM Operating System/400®(product number

5722–SS1) and to all subsequent releases and modifications until otherwise indicated in new editions. This version

does not run on all reduced instruction set computer (RISC) models nor does it run on CISC models.

US Government Users Restricted Rights –Use, duplication or disclosure restricted by GSA ADP Schedule Contract

with IBM Corp.

Contents

Chapter 1. Power supply and air moving

device ...............1

Chapter 2. Before you begin ......3

Chapter 3. Replace power supply in

iSeries 820 or 5075, 5095, or 0595

expansion unit ............5

Chapter 4. Replace power supply in

iSeries 825 .............7

Chapter 5. Install power supply in

iSeries 820 or 5075, 5095, or 0595

expansion unit ...........11

Details: Install power supply in iSeries 820 or 5075,

5095, or 0595 expansion unit.........11

Chapter 6. Replace the air moving

device ...............13

Chapter 7. Install the air moving device 15

Details: Install the air moving device ......16

Remove the covers .........17

820, 5075, or 5095 front cover ........17

825 front cover .............18

820, 5075, and 5095 side and back cover .....18

825 back cover .............20

System units in arack ...........21

Power down the system .......23

Power on the system ........25

Locations .............27

820 air moving device (AMD) and power supply

location................28

825 air moving device (AMD) and power supply

location................29

5075, 5095 or 0595 air moving device (AMD) and

power supply location...........30

Appendix. Notices ..........31

Trademarks ..............32

Terms and conditions for downloading and printing

publications ..............33

Code disclaimer information.........34

Electronic Emission Notices .........34

Federal Communications Commission (FCC)

statement ..............34

Electronic Emission Notices .........36

Federal Communications Commission (FCC)

statement ..............36

©Copyright IBM Corp. 2000, 2005 iii

iv 5138, 5155, 5156, 5157 Power Supply and Air Moving Device V5R3

Chapter 1. Power supply and air moving device

Replacing and installing the power supply and air moving device are customer

tasks. You may be able to install or replace apower supply or an air moving

device with the unit powered on. When you use these instructions, you will

perform some or all of the following tasks:

vPerform prerequisite tasks.

vPower down the system.

vRemove the system unit covers.

vRemove hardware.

vInstall new hardware.

vInstall covers.

You need to allow additional time to complete your jobs, back up your system,

perform an initial program load (IPL) of your system, and verify your hardware

configuration.

You can choose to perform these tasks yourself or contact IBM(R) or an authorized

service provider to make arrangements for them to perform the tasks for afee.

Should you encounter difficulties when performing atask, contact your authorized

dealer or service provider.

Select the instructions for the task you want to perform:

vChapter 3, “Replace power supply in iSeries 820 or 5075, 5095, or 0595 expansion

unit,” on page 5

vChapter 4, “Replace power supply in iSeries 825,” on page 7

vChapter 6, “Replace the air moving device,” on page 13

vChapter 5, “Install power supply in iSeries 820 or 5075, 5095, or 0595 expansion

unit,” on page 11

vChapter 7, “Install the air moving device,” on page 15

©Copyright IBM Corp. 2000, 2005 1

25138, 5155, 5156, 5157 Power Supply and Air Moving Device V5R3

Chapter 2. Before you begin

Before you begin areplacement or installation task, follow these steps:

__ 1. For an installation and if possible, for areplacement, ensure that you have

acurrent backup of your system (including operating system, licensed

programs, and data). If you have backed up the operating system and

licensed programs since the last time you applied PTFs, that backup is

acceptable.

__ 2. Ensure that you take afew minutes to become familiar with these

instructions.

__ 3. Ensure that you have access to amedium flat-bladed screwdriver.

__ 4. If there are incorrect, missing, or visibly damaged parts, contact one of the

following:

vYour authorized service provider

vIn the United States: IBM®Rochester Manufacturing Automated

Information Line (R–MAIL) at 1–800–300–8751

vIn countries outside of the United States: Use the following Web site to

locate your service and support numbers:

http://www.ibm.com/planetwide

__ 5. If you are installing new hardware in logical partitions, you need to plan

and understand the requirements to be successful. Go to Logical partitions

in the Information Center.Then return to these instructions.

__ 6. If you encounter difficulties during the procedure, contact your authorized

service provider or your authorized dealer.

__ 7. Determine if there are any existing PTF prerequisites before you install your

new feature. Go to the following Web site:

http://www-912.ibm.com/s_dir/slkbase.NSF/slkbase

a. Select All Documents.

b. Select General Information.

c. Select Offerings.

d. Select Feature Prerequisites.

e. Select Customer Installation Features Prerequisites.

f. Locate your feature number and OS/400®release, and check the

prerequisites.

©Copyright IBM Corp. 2000, 2005 3

45138, 5155, 5156, 5157 Power Supply and Air Moving Device V5R3

Altri manuali per i Series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali IBM Server

IBM

IBM System z10 EC Manuale utente

IBM

IBM BladeCenter GPU Expansion Blade Manuale utente

IBM

IBM 326m - eServer - 7969 Manuale utente

IBM

IBM System x3690 X5 Manuale utente

IBM

IBM 8676G1X Manuale utente

IBM

IBM SAN Volume Controller 2145-SV1 Manuale

IBM

IBM RS/6000 SP Manuale utente

IBM

IBM 783722U Manuale utente

IBM

IBM 8832L1X Istruzioni operative

IBM

IBM 150 Scheda informativa del prodotto

IBM

IBM i 830 Istruzioni operative

IBM

IBM eServer 330 xSeries Manuale utente

IBM

IBM 79463AU Manuale utente

IBM

IBM x3200 - System M3 - 7328 Manuale utente

IBM

IBM eServer xSeries 135 Manuale utente

IBM

IBM iDataPlex dx360 M4 Manuale utente

IBM

IBM e Server iSeries 825 Manuale utente

IBM

IBM XSERIES 255 TYPE 8685 Manuale utente

IBM

IBM 865511Y - Netfinity 3500 M10 Manuale del proprietario

IBM

IBM B50 Manuale utente

IBM

IBM 7870B4U Manuale utente

IBM

IBM eServer xSeries 300 Scheda informativa del prodotto

IBM

IBM eserver xSeries 220 Type 8648 Manuale utente

IBM

IBM S822LC Manuale utente

Manuali Server popolari di altre marche

HP AlphaServer ES47 Manuale utente

Dell

Dell PowerEdge R410 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

Dell

Dell PowerEdge XE9640 Manuale

Dell

Dell PS4100 Istruzioni di montaggio

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

HP ProLiant Gen9 Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

Dell

Dell PowerEdge 3YPMN Manuale utente

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

HP Integrity rx2600 Guida all'installazione

Milestone

Milestone Husky IVO 350T Manuale utente

IBM i Series Manuale utente

Manuali Server popolari di altre marche