ICM Controls ICM2805A Istruzioni generali

 Thisboardshouldbeinstalledbyaqualiedtechnician

only.Failuretofollowtheseinstructionscouldleadto

propertydamage,personalinjuryordeath.

 Disconnectthepowersupplybyturningoffacircuit

breakerorremovingafusebeforeattemptingtoinstall

thisboard.

1.Turnoffthepowersupplytothefurnacebyremovingthefuseor

turningoffthecircuitbreaker.

2.Removethewiresandconnectorsfromtheoldboardoneat

atime.CarefullyconnectthemtotheICM2805Atopreventa

miswire.Removethemountingscrewsandthenremovetheold

controlboard.

3.Placethetemplate(onthebackofthissheet)inthecontrolbox

andsecurewithtape.Moveallwiresoutofthewayandcarefully

drillfour3/16”diameterholesasshownonthetemplate.

Removeanddiscardthetemplate.

4.MounttheICM2805Awiththefuseatthetopbyinsertingthe

standoffsintothemountingholes.

NOTE:Do not ex the ICM2805A circuit board. Apply pressure

only at the standoffs.

5.Disconnectthe6-pinconnectorplug.UsinganAMPextractor

tool#458994-2removethebluewirefromsocketposition#4

andinstallitinposition#1.(seediagramatright).Ifthetoolis

notavailableproceedasfollows:

 Cutoffthebluewireatsocketposition#4intheconnector(see

diagramatright),andstriptheinsulationback3/8”.Insertthe

lengthofbluewireprovidedinsocketposition#1,nexttothecut

offbluewire.Reconnectthe6-pinconnectorplug.Connectthe

looseendsofthebluewiresusingthewirenutprovided.Tape

thewirenutconnectionwithelectricaltapesoitcannotloosen.

6.ApplythenewwiringdiagramforG4furnacessuppliedwiththe

ICM2805Atotheinsideofthecabinet.

7.Turnonthepowersupplyandcheckthefurnaceforproper

operation.

G3RC and G4 Furnace Models

ICM2805A 1.Turnoffthepowersupplytothefurnacebyremovingthefuseor

turningoffthecircuitbreaker.

2.Removethewiresandconnectorsfromtheoldboardoneat

atime.CarefullyconnectthemtotheICM2805Atopreventa

miswire.Removethecontrolbracketmountingscrewsfrom

theoutsideofthecabinet(exceptG5RLmodels).Installthe

newcontrolbracketandthenproceedtostep4.Ifthescrews

arenotaccessible,newmountingholesmustbedrilledinthe

existingmountingbracketusingthetemplateonthebackofthis

instructionsheet.

3.Removethescrewsecuringtheoldcontrolboardandthen

removetheoldcontrolboard.Placethetemplate(onthebackof

thissheet)overthemountingbracketandsecurewithtape.Move

allwiresoutofthewayandcarefullydrillfour3/16”diameterholes

asshownonthetemplate.Removeanddiscardthetemplate.

4.MounttheICM2805Awiththefuseatthetopbyinsertingthe

standoffsintothemountingholes.

NOTE:Do not ex the ICM2805A circuit board. Apply pressure

only at the standoffs.

5.ApplythenewwiringdiagramforG5furnacessuppliedwiththe

ICM2805Atotheinsideofthecabinet.

6.Turnonthepowersupplyandcheckthefurnaceforproper

operation.

G5 Furnace Models

1.Turnoffthepowersupplytothefurnacebyremovingthefuseor

turningoffthecircuitbreaker.

2.Removethewiresandconnectorsfromtheoldboardoneat

atime.CarefullyconnectthemtotheICM2805Atopreventa

miswire.

3.Removetheoldboardbycuttingoffthestandoffs.Installthe

ICM2805Ainthesamepositionbysnappingthestandoffsintothe

mountingholes.

 NOTE:Do not ex the ICM2805A circuit board. Apply pressure

only at the standoffs.

4.Turnonthepowersupplyandcheckthefurnaceforproper

operation.

G6, M2 & M3 Furnace Models

6-pinwireconnector

Whitewire

Blackwire

Bluewirecut

InsertedBluewire

(provided)

ExistingBluewire

(Previouslycutfromslot4)

Whitewire

Blackwire

ExistingBluewire

(Tobecut&connected

towireprovided)

Cutexistingblue

wirehere

InsertBluewire

(provided)

6-pinwireconnector

7313WilliamBarryBlvd.,NorthSyracuse,NY13212

(TollFree)800-365-5525(Phone)315-233-5266(Fax)315-233-5276

www.icmcontrols.com

ONE-YEAR LIMITED WARRANTY

TheSellerwarrantsitsproductsagainstdefectsinmaterialorworkmanshipforaperiodofone(1)

yearfromthedateofmanufacture.TheliabilityoftheSellerislimited,atitsoption,torepair,replace

orissueanon-casecreditforthepurchasepricesofthegoodswhichareprovidedtobedefective.

Thewarrantyandremediessetforthhereindonotapplytoanygoodsorpartsthereofwhichhave

beensubjectedtomisuseincludinganyuseorapplicationinviolationoftheSeller’sinstructions,

neglect,tampering,improperstorage,incorrectinstallationorservicingnotperformedbytheSeller.

InordertopermittheSellertoproperlyadministerthewarranty,theBuyershall:1)NotifytheSeller

promptlyofanyclaim,submittingdatecodeinformationoranyotherpertinentdataasrequestedby

theSeller.2)PermittheSellertoinspectandtesttheproductclaimedtobedefective.Itemsclaimed

tobedefectiveandaredeterminedbySellertobenon-defectivearesubjecttoa$30.00perhour

inspectionfee.ThiswarrantyconstitutestheSeller’ssoleliabilityhereunderandisinlieuofanyother

warrantyexpressed,impliedorstatutory.Unlessotherwisestatedinwriting,Sellermakesnowarranty

thatthegoodsdepictedordescribedhereinaretforanyparticularpurpose. LIAF117-1

G5RLModels:Foldbackonline

G5RLModelsonly:Foldpaperbackalongdashedlineandplacethis

corneronlower-leftcornerofmontingpanel.

AllG4andG5furnaces,exceptG5RLModels:

Placethiscornerofthetemplateinthecornerofthecontrolbox,nexttocutout(G4),

oronlower-rightcornerofmountingpanel(G5)

Unsethistemplateto

carefullydrill(4)3/16”holes.

ICM2805A Fault Codes

LED’S Flashes FaultCondition

Red ON Normaloperation

1Flash Limitswitchesopen

2Flashes Pressureswitchstuckopen

3Flashes Pressureswitchstuckclosed

4Flashes Ignitionfailure(5trials)

5Flashes HotandNeutralreversedornoground

6Flashes Brownoutvoltage

Continuous FaultameorGasvalverelayshort

Yellow Continuous LowameorNoame

ON Flamepresent

Thiscontrolhasbuilt-inself-diagnosticcapability.Ifasystemproblemoccurs,ablinkingLEDshowsafaultcode.

Altri manuali ICM Controls Sistema di controllo

ICM Controls

ICM Controls ICM2813 Istruzioni generali

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente