ICP DAS USA M-7002 Manuale utente

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7002

4-channel AI, 5-channel DI and 4-channels

Relay OutputData Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7002.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7002 is a 16-bit, 4-channel differential analog inputs 5-channel digital inputs and

4-channels for relay output. All of its channels are Form A type relay module that

provides programmable input range on all analog channels (+/-150 mV, +/-500 mV, +/-1

V, +/-5 V, +/-10 V, +/-20 mA, 0 ~ 20 mA and 4 ~ 20 mA) and digital output can be set

alarm output with shortcircuit protection and overload protection. Each analog channel

is allowed to configure an individual range and has 240 Vrms high overvoltage

protection. Jumper selectable for voltage or current input. The sampling rate of M-7002

is changeable; there are fast mode and normal mode for your consideration. M-7002

also has qualification for 4 kV ESD protection as well as 2500 VDC intra-module

isolation.

2. Terminal Assignment

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

4. Default Settings

Default settings for the M-7005 modules are as follows:

▫Protocol: Modbus RTU

▫Module Address: 01

▫Thermistor Type: Type 60, PreCon Type III, -30°F to 240°F

▫Baud Rate: 9600 bps

▫Temperature Scale: Celsius (the M-7005 also supports Fahrenheit for DCON protocol)

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the thermistor analog input.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to

search module. The default settings for the module can be found in Section 3. Click OK

after selecting the COM port setting.

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For M-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See Section 2.1 for

details. To configure the M-7005, the $AA7CiRrr command must also be sent. See user

manual Section 2.12 for details. For M-7000 modules using the Modbus RTU protocol,

configure the module using the following functions.

-Sub-function 04h of Function 46h, see user manual Section 3.6.2

-Sub-function 06h of Function 46h, see user manual Section 3.6.4

-Sub-function 08h of Function 46h, see user manual Section 3.6.6

Read data from the input channels: send either the #AA or #AAN commands to the

module. See user manual Sections 2.3 and 2.4 for details. For M-7000 modules using

the Modbus RTU protocol, use Function 04h to read the data from the input channels.

See user manual Section 3.3 for details.

M-7002 - 4-ch AI, 5-ch DI and 4-ch Relay Output DAQ Module - QuickStart (Jun/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Indice

Altri manuali ICP DAS USA Unità di controllo

ICP DAS USA

ICP DAS USA I-7080 Manuale utente

ICP DAS USA

ICP DAS USA I-8014W Manuale utente

ICP DAS USA

ICP DAS USA MDC-714i Manuale utente

ICP DAS USA

ICP DAS USA ECAT-201x EtherCAT Slave I/O Manuale utente

ICP DAS USA

ICP DAS USA M-7051 Manuale utente

ICP DAS USA

ICP DAS USA ET-2200 Series Manuale utente

ICP DAS USA

ICP DAS USA tPET-P2R2 Manuale utente

ICP DAS USA

ICP DAS USA IR-310-RM Manuale utente

ICP DAS USA

ICP DAS USA I-7052D Manuale utente

ICP DAS USA

ICP DAS USA tET-P2A2 Manuale utente

ICP DAS USA

ICP DAS USA I-8026W Manuale utente

ICP DAS USA

ICP DAS USA PM-3133i Manuale utente

ICP DAS USA

ICP DAS USA tSH-735 Manuale utente

ICP DAS USA

ICP DAS USA tPET-P6 Manuale utente

ICP DAS USA

ICP DAS USA I-7045 Manuale utente

ICP DAS USA

ICP DAS USA PM-3033 Series Manuale utente

ICP DAS USA

ICP DAS USA MN-3253 Series Manuale utente

ICP DAS USA

ICP DAS USA tZT-P4C4 Manuale utente

ICP DAS USA

ICP DAS USA M-7069D Manuale utente

ICP DAS USA

ICP DAS USA I-7188XA Manuale utente

ICP DAS USA

ICP DAS USA PETL-7060 Manuale utente

ICP DAS USA

ICP DAS USA ZT-2053 Manuale utente

ICP DAS USA

ICP DAS USA MDC-700 Series Manuale utente

ICP DAS USA

ICP DAS USA I-7063 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente