ICP DAS USA M-7067 Manuale utente

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

M-7067

7 Channel Form A Relay Output Digital Input

Data Acquisition Module

Quick Start Guide

Product Website:

https://www.icpdas-usa.com/m_7067_m_7067d.html

http://www.icpdas-usa.com/dcon_utility_pro.html

1. Introduction

The M-7067 device is a network data acquisition and control module that

support Modbus RTU. They can be remotely controlled using a set of

commands called DCON protocol. With the Modbus RTU protocol, it can

easily communicate with most popular SCADA/ HMI software and PLCs.

2. Terminal Assignment

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

3. Block/ Wiring Diagram

4. Default Settings

。Module Address: 01

。DIO Type: Type 40

。Baud Rate: 9600 bps

。Checksum disabled

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. Configuration

To install the module, follow the steps below:

1. Connect the digital input and output.

2. Connect the module to the RS-485 network using the DATA+ and DATA- terminals. If

the host is only equipped with an RS-232 interface, then an RS-232 to RS-485

converter will be required.

3. Connect the module to the power supply using the +Vs and GND terminals. Note that

the voltage supplied should be in the range of +10 to +30V DC.

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

4. Open DCON utility pro

click on COM port(first icon).

It can select multi-options such as Baud Rate, Protocol, Checksum, and Format

to search module. The default settings for the module can be found in Section 3.

Click OK after selecting the COM port setting.

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

5. DCON utility pro will search for the selected COM port according the setting

previously set. DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS

and the others modules.

6. Configuration I/O module setting on PC

M-7067 7 Ch Form A Relay Output DAQ Module- QuickStart (Apr/2018)

ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717

7. For I-7000 modules, DCON utility pro terminal can send command to the module.

See user manual Sections 2 for details command.

Configure the module: sending the %AANNTTCCFF command. See user manual

Section 2 for details.

Read data from the input channels: send either the #AA or #AAN command to the

module.

8. If user doesn’t know command, user can select Address and ID, it will show some

refer commands as below. User can select necessary command to test or debug

modules.

Indice

Altri manuali ICP DAS USA Unità di controllo

ICP DAS USA

ICP DAS USA I-7045 Manuale utente

ICP DAS USA

ICP DAS USA ECAT-2000 Series Manuale utente

ICP DAS USA

ICP DAS USA Zigbee ZT-2060 Manuale utente

ICP DAS USA

ICP DAS USA M-7041D Manuale utente

ICP DAS USA

ICP DAS USA SG-3016 Manuale utente

ICP DAS USA

ICP DAS USA MDC-700 Series Manuale utente

ICP DAS USA

ICP DAS USA M-7016 Manuale utente

ICP DAS USA

ICP DAS USA MDC-700 Series Manuale utente

ICP DAS USA

ICP DAS USA LinPAC-51 Series Manuale utente

ICP DAS USA

ICP DAS USA M-7069D Manuale utente

ICP DAS USA

ICP DAS USA SG-3227 Manuale utente

ICP DAS USA

ICP DAS USA tET-P2A2 Manuale utente

ICP DAS USA

ICP DAS USA ZT-2055 Manuale utente

ICP DAS USA

ICP DAS USA I-7083 Manuale utente

ICP DAS USA

ICP DAS USA EIP-2060 Manuale utente

ICP DAS USA

ICP DAS USA tSG-3781B Manuale utente

ICP DAS USA

ICP DAS USA M-7064 Manuale utente

ICP DAS USA

ICP DAS USA I-7045D Manuale utente

ICP DAS USA

ICP DAS USA I-7014D Manuale utente

ICP DAS USA

ICP DAS USA M-7051D Manuale utente

ICP DAS USA

ICP DAS USA WF-2017 Manuale utente

ICP DAS USA

ICP DAS USA HRT-370 Manuale utente

ICP DAS USA

ICP DAS USA I-8014W Manuale utente

ICP DAS USA

ICP DAS USA I-7080 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente