iGuard IP-101S Manuale utente
iGuard
IP-101S
USB Network Video Server
User’s Manual
Version 2.5
i
CONTENTS
Chapter 1 Introduction_________________________________________ 4
1.1 Features ________________________________________________ 4
1.2 Function ________________________________________________ 4
1.3 Package Contents_________________________________________ 5
Chapter 2 iGuard Module_______________________________________ 6
Chapter 3 Hardware Installation _________________________________ 7
3.1 Installation Procedure______________________________________ 8
Chapter 4: iGuard Web Manager________________________________ 10
4.1 Introduction_____________________________________________ 10
4.2 iGuard Web Manager Interface______________________________ 11
4.2.2 Information____________________________________________ 13
4.2.2.1 System Status________________________________________ 13
4.2.2.2 Current Connections___________________________________ 14
4.2.2.3 Event Log ___________________________________________ 15
4.2.3 Basic Settings _________________________________________ 16
4.2.3.1 Camera Settings______________________________________ 16
4.2.3.2 Network_____________________________________________ 18
4.2.3.3 Account Settings______________________________________ 21
4.2.4 Advanced Settings______________________________________ 23
4.2.4.1 Event Notification _____________________________________ 23
4.2.4.2 Motion Detection______________________________________ 27
4.2.4.3 Image Recording _____________________________________ 30
4.2.4.4 E-mail / FTP _________________________________________ 31
4.2.4.5 System Settings ______________________________________ 34
4. 2.4.7 About ______________________________________________ 36
Chapter 5: iGuardware________________________________________ 38
5.1 Installing iGuardware _____________________________________ 38
5.2 Using iGuardware________________________________________ 39
5.2.1 iGuard Utility __________________________________________ 39
5.2.1.1 Setup Wizard ________________________________________ 40
5.2.1.2 Launch iGuard _______________________________________ 44
5.2.1.3 IP Configuration ______________________________________ 45
5.2.1.4 Upgrade Firmware ____________________________________ 48
5.2.2 iGuardView ___________________________________________ 50
ii
5.2.2.1 Device Setting________________________________________ 51
5.2.2.2 Camera Setting_______________________________________ 53
5.2.2.3 Motion Detection Setting________________________________ 54
5.2.2.4 Email Notification Setting _______________________________ 56
5.2.2.5 SNMP Setting ________________________________________ 57
5.2.2.6 Camera Monitor ______________________________________ 58
5.2.2.7 View _______________________________________________ 61
5.2.2.8 System _____________________________________________ 61
5.2.2.9 Help________________________________________________ 62
Appendix A: Router Configuration______________________________ 63
Appendix B: IP Address, Subnet and Gateway____________________ 81
Appendix C: Glossary ________________________________________ 83
iii
Chapter 2 :iGuard 101 Module
Chapter 1 Introduction
1.1 Features
iGuard is an affordable, versatile and flexible remote monitoring solution for small
business, retail store, and residential applications. iGuard features a built-in web
server (iGuard-IP-101S module) with a range of USB cameras to choose from,
eliminating the need to have a computer to stream video images to the internet. Each
system can simultaneously support any two combinations of USB PC cameras be it
regular, infrared or pan-tilt. With its built-in web-server. iGuard features a
Windows-based software that allows the user to archive streaming video directly into
the hard-drive. The same software also allows the user to monitor multiple cameras
on one screen.
Features:
•Built-in Web Server
•10/100Mbps Fast Ethernet Network Access
•Support Any Java-Enabled Web Browser
•LCD display shows the IP address, Subnet Mask and Gateway
•32-Bit RISC CPU
•1MB Flash Memory
•8MB Dynamic Memory
•Support Up to 30 Remote Viewers for each camera
•Allow Up to 8 User Accounts and Passwords
•5.3VDC 1A Maximum
•Operating Temperature: 0°C ~ 60°C
•Operating Humidity: 10% ~ 90%
•Dimensions: 48mm x 63mm x 21m
•Weight: 75g
•Network Protocol: HTTP, TCP/IP, UDP, SMTP, PPPoE, Dynamic DNS, DNS
Client, SNTP, BOOTP, DHCP, FTP, SNMP
•Support All USB PC Camera with VIMICRO ZC0301+DSP processor
•Resolution: 640 x 480, 320 x 240, 160 x 120.
•Frame Rate: Up to 20fps in 320 x 240
•Motion JPEG streaming video
•2 USB Ports for PC Cameras
•USB 1.1 & 2.0 compliant
•Support two different PC cameras
•Support Pan/Tilt and Infrared USB PC Camera
1.2 Function
The most important function of iGuard is for remote surveillance. Once iGuard is
installed, the user can check any of the connected PC cameras via any web browser.
The user can monitor and control these cameras simply by entering the IP address of
the iGuard from anywhere in the world as long as there is an Internet connection. For
4
Chapter 2 :iGuard 101 Module
instance, the user can be in Australia but he or she can monitor the production facility
in China, and if he or she likes, also check on the branch office in Singapore at the
same time.
Fig.1. iGuard Network Diagram
1.3 Package Contents
Your iGuard package should contain the following items;
1. iGuard IP-101S module,
2. 10-100 Ethernet Cable
3. Pan/Tilt/Zoom (Digital) Camera
4. 5.3V DC Adapter
5
Chapter 2 :iGuard 101 Module
Chapter 2 iGuard Module
Fig.2. iGuard IP-101S Module
LED Status Indicators on iGuard
Light color Signal definition Condition description
Green Power state On: Normal power
Red Error Condition On: Error condition occurred
Orange Logon state On: When there is user logon and
receive the image.
Yellow USB data activity Flash when there is data
transmit/receive on the USB.
Fig.3. iGuard Status LED Indicator
Light indicators on iGuard LAN Port LED
Light color Condition description
Green On: Internet correspond speed is 100M
Flash: Data transmitting/receiving
Yellow On: Internet correspond speed is 10M
Flash: Data transmitting/receiving
Fig.4. iGuard LAN LED Indicators
6
Chapter 3:Hardware Installation
Chapter 3 Hardware Installation
Before you start using iGuard, you will need to set-up both the hardware and software.
The following is a flow chart on the installation procedure:
1 Connect USB Camera ,network
cable, and power Adapter
To iGuard module
2 Connect Network cable to ROUTER
/ DSL or Cable modem
3 Setup iGuard Web Manager
(Chapter 4) and iGuard-Viewer
(Chapter5) (Otional)
4 Router Programming (Appendix).
5 iGuard set-up completed
7
Chapter 3:Hardware Installation
3.1 Installation Procedure
Step 1:
Connect the USB camera
into any available USB port
on the iGuard IP-101S.
The first camera that plugs
into the unit will be
designated as Camera A.
Step 2:
Plug the included Ethernet
cable to the network port on
the iGuard IP-101S., the
other end to a modem or a
router
Step 3:
Connect DC power adapter
output into iGuard IP-101S
socket, and plug the DC
power input into the wall
socket
8
Chapter 3:Hardware Installation
Step 4:
The LCD will display the IP,
Subnet Mask and Gateway
IP if there is a DHCP server
on the network. Make a
note of the IP address of
the iGuard. You will use this
IP address to login into the
iGuard to configure and
monitor the camera.
The icon on the LCD
shows that a USB camera
is connected.
Warning:
Please make sure the input Voltage and Frequency of the DC power adapter (DC
5.3V) is correct before plugging into the power outlet!
9
Indice
