IN-COMMAND NCSP3CM Manuale utente

RV CONTROL AND MONITORING SYSTEM

Patent # (D776,068)

Patent # (D762,644)

Patent # US 9,679,735

™

NCSP3CM

Installation and Operation Manual (English)

NCSP3DCCT

NCSP3CM

Read the iN-Command Manual, and these warnings and instructions carefully before using this product. Failure to follow the use

instructions in this owner’s manual, or improper use of the Mobile Application, Display Commander and/or Body Control Module, could

result in personal injury, including death.

Do not operate while vehicle is being driven.

The Mobile Application, Display Commander and/or Body Control Module should not be used while the vehicle is being driven. Use of

the Mobile Application, Display Commander and/or Body Control Module while the vehicle is being driven is dangerous and may cause

personal injury or property damage.

For adult use only.

The Mobile Application, Display Commander and Body Control Module are intended for adult use only, and are not to be used by persons

under the age of 18. Use by children may cause personal injury or property damage.

Operate only when you have a clear line of sight.

Do not operate any moving parts (including, but not limited to, awnings, jacks and slides), unless you have a clear line of sight to the

moving part. The Mobile Application, Display Commander or Body Control Module may be used only if you are giving instructions to, and

receiving instructions from, another person at least age 18 or older who can clearly see the moving part. Failure to follow these instructions

may result in serious personal injury or property damage.

Do not operate under the inuence of alcohol or drugs.

Do not operate the Mobile Application, Display Commander or Body Control Module while under the inuence of alcohol or drugs. Doing

so may result in personal injury or property damage.

Avoid moisture.

To reduce the risk of re or electric shock, do not expose this equipment to rain or moisture.

Use recommended accessories.

To reduce the risk of re or electric shock and annoying interference, use only the recommended accessories.

Important Safety Information

NCSP3CM

TABLE OF CONTENTS ...........................................................3

INTRODUCTION .....................................................................4

Thank You!............................................................................4

Features................................................................................4

Precautions...........................................................................4

Packing List ..........................................................................4

INSTALLATION ........................................................................5

Tools and Supplies................................................................5

Disconnecting the Battery.....................................................5

Selecting the Mounting Location...........................................5

Mounting the Display Commander (DC)...............................5

WIRING ...................................................................................6

RV-C SYSTEM LAYOUT .........................................................7

SETUP MENU LIST .................................................................8

TRAVEL LOCKOUT (Safety) ...................................................9

OVERRIDE SWITCHES * ......................................................10

DISPLAY COMMANDER BUTTONS .....................................10

SPECIFICATIONS ................................................................. 11

FCC NOTES .......................................................................... 11

PASSCODE PROTECTION ..................................................12

PANIC WARNING ..................................................................12

SETTINGS .............................................................................12

Text Editing*........................................................................12

Scroll List Editing ................................................................14

Triggers ..............................................................................15

Generator Fuel ...................................................................15

Alarm Inputs........................................................................15

Passcode ............................................................................15

Set Passcode Timer.......................................................16

Change Passcode .........................................................17

Clear Passcode .............................................................17

Reset All Settings...........................................................17

MOBILE DEVICES: .................................................................. 18

Pairing iOS Mobile Device to DC........................................... 19

Pairing Android Mobile Device to DC..................................... 22

Loading the DC Floor Plan .................................................... 24

LANGUAGE SELECTION ........................................................ 25

CHECKING ACTIVE BLUETOOTH SESSION* ........................ 26

HVAC ........................................................................................ 27

Vent Fans............................................................................... 27

Fan Only Mode ...................................................................... 27

AC Cooling............................................................................. 27

Heating .................................................................................. 28

Auto ....................................................................................... 28

Date & Time ........................................................................... 29

HVAC Schedule ..................................................................... 30

AUTO GENERATOR START .................................................... 30

Generator Schedule............................................................... 31

SOFTWARE UPDATE* ............................................................. 32

GLOBAL CONNECT* ............................................................... 35

FLOOR PLAN ........................................................................... 38

Reset ..................................................................................... 38

Custom* ................................................................................. 39

Notications ........................................................................... 40

TOUCH SCREEN CALIBRATION ............................................ 42

SYSTEM CALIBRATION * ........................................................ 43

TROUBLESHOOTING .............................................................. 45

• TABLE OF CONTENTS

NCSP3CM

• Thank You!

Thank you for choosing a iN-Command product. We hope you will nd

the instructions in this owner’s manual clear and easy to follow. If you

take a few minutes to look through it, you’ll learn how to use all the

features of your new iN-Command system for maximum enjoyment.

• Features

Features of iN-Command system include:

• Simultaneous control by up to three Android Devices and

one iOS Device

• Control four zones of Interior Lighting

• Control three zones of Exterior Lighting

• Monitor all water and fuel tank levels

• Control and monitor the Water Heater

(switches between LP, AC, or both)

• Control and monitor the Water Pump

• Control and monitor the Generator (including all faults)

• Control Awnings & Awning Lights

• Control Electric and Hydraulic Slides

• Control Jacks (non-automatic function)

• 4 Programmable Auxiliary 12V Triggers

• 4 Alarm Inputs (12V)

• Monitor Battery Voltage with Low Voltage Alert

• Auto Generator Start

• HVAC

• Global Connect

• Precautions

• Use the Proper Power Supply.

This product is designed to operate with a 12 volt DC, negative

ground battery system (the standard system in a North American vehicle).

• Use Authorized Service Centers.

Do not attempt to disassemble or adjust this precision product;

contact a professional for assistance.

• Avoid Moisture.

To reduce the risk of re or electric shock, do not expose this

equipment to rain or moisture.

(1) Cover, (2) Thumb Screws (1) Body Control Module (BCM)

(1) Display Commander (NCSP3DCCT)

• Packing List

• Avoid Cleaning Products.

The front of this unit should only be cleaned with a slightly damp cloth.

Do not use cleaning products.

• Use Recommended Accessories.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND

ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED

ACCESSORIES.

• INTRODUCTION

NCSP3CM

It’s a good idea to read all of the instructions before beginning

the installation.

• Tools and Supplies

You will need these tools and supplies to install your iN-Command:

• Phillips screwdriver

• #2 square drive bit

• Wire cutters and strippers

• Electrical tape

• Volt meter/test light

• Crimping tool

• Fork Crimp connectors

• Minimum of 24 gauge wire required to connect DC to BCM

• 10 gauge wire for power and slide connections

• 14 and 18 gauge wire for all other connections

• Four #8 PH (0.164” x 0.75”) screws for the DC

• Six #8 PH (0.164” x 1.0”) screws for the BCM

• Disconnecting the Battery

To prevent a short circuit, be sure to turn off 12V power and

remove the negative (-) battery cable prior to installation.

• Selecting the Mounting Location

Select a mounting location, taking care to avoid the following:

• Places exposed to heat-radiating appliances such as electric heaters

• Adjacent to other equipment that radiates heat

• Poorly-ventilated or dusty places

• Moist or humid locations

CUTOUT FOR DISPLAY COMMANDER (DC)

NOTE: Before cutting the mounting hole, make sure the area

behind the mounting location is clear of wires, fuel and vacuum

or water lines; ensure there is at least a 2.75”clearance below

the Display Commander to allow for programming by USB stick.

RECOMMENDED CUTOUT

WALL FOR

REFERENCE

CUTOUT 4 11/16"

7 1/4"

• Mounting the Display Commander (DC)

• Use the mounting hole diagram to measure and cut a mounting

hole, allowing space below for future programming via USB drive

• Route power wires through the hole and connect

• Check and ensure correct operation

• Mount the unit using four #8 PH (0.164” x 0.75”) screws

• Attach Trim ring

• INSTALLATION

61 - +12V WATER HEATER FAULT IN (GREEN)

60 - WATER HEATER ELECTRIC +12V 1A OUT (YELLOW)

59 - WATER HEATER GAS +12V 1A OUT(ORANGE)

58 - WATER HEATER GND (RED)

57 - TRAVEL LOCK IN 12V (BROWN)

56 - INPUT 4 (GRAY)

55 - INPUT 3 (PURPLE)

54 - INPUT 2 (BLUE)

53 - INPUT 1 (GREEN)

52 - AUX4 +12V OUT (YELLOW)

51 - AUX3 +12V OUT (ORANGE)

50 - AUX2 +12V OUT (RED)

49 - AUX1 +12V OUT (BROWN)

1 - FRESH 1 TANK IN (BROWN)

2 - FRESH 2 TANK IN (RED)

3 - BLACK 1 TANK IN (ORANGE)

4 - BLACK 2 TANK IN (YELLOW)

5 - GREY 1 TANK IN (GREEN)

6 - GREY 2 TANK IN (BLUE)

7 - GREY 3 TANK IN (PURPLE)

8 - TANK LEVEL COMMON 7VDC (GRAY)

48 - NC (GRAY)

47 - NC (PURPLE)

46 - GND HYDRAULIC VALVE 1.5A (BLUE)

45 - +12V HYDRAULIC VALVE 1.5A (GREEN)

44 - HYDRAULIC RETRACT OUT 12V 2A (YELLOW)

43 - HYDRAULIC EXTEND OUT 12V 2A (ORANGE)

42 - GND HYDRAULIC VALVE 1.5A (LANDING GEAR)(RED)

41 - +12V HYDRAULIC VALVE 1.5A (LANDING GEAR)(BROWN)

40 - GENERATOR GND (GRAY)

39 - GENERATOR FUEL LEVEL IN (PURPLE)

38 - GENERATOR HOUR METER 12V IN (BLUE)

37 - GENERATOR SERVICE 12V IN (GREEN)

36 - GENERATOR PRIME/STOP 12V 1A OUT (YELLOW)

35 - GENERATOR START 12V 1A OUT (ORANGE)

34 - FUEL STATION GND (RED)

33 - FUEL STATION TANK LEVEL IN (BROWN)

93/94/97/98 - NC

92 - CAN LOW

91 - CAN HIGH

96 - CAN LOW

95 - CAN HIGH

100 - GND

99 - +12VDC OUT

DETAIL G

DETAIL A

DETAIL B

DETAIL C

DETAIL D

DETAIL E

9 10 11 12 13 14 15 16 17 18 1 9 2 0 2 1 22 23 24 2 5 2 6 2 7 2 8 29 30 31 32

63 62

72 71 70 69 68 67 66 65 64

81 80 79 78 77 76 75 74 73

90 89 88 87 86 85 84 83 82

10 - LIGHT GROUP 1 12V 15A IN

9 - LIGHT GROUP 1 SWITCH INPUT 12V

28 - EXTERIOR LIGHT 12V 15A OUT

27 - EXTERIOR LIGHT GND

26 - EXTERIOR LIGHT 12V 15A IN

25 - EXTERIOR LIGHT SWITCH INPUT 12V

12 - LIGHT GROUP 1 12V 15A OUT

11 - LIGHT GROUP 1 GND

24 - LIGHT GROUP 4 12V 15A OUT

23 - LIGHT GROUP 4 GND

22 - LIGHT GROUP 4 12V 15A IN

21 - LIGHT GROUP 4 SWITCH INPUT 12V

20 - LIGHT GROUP 3 12V 15A OUT

19 - LIGHT GROUP 3 GND

18 - LIGHT GROUP 3 12V 15A IN

17 - LIGHT GROUP 3 SWITCH INPUT 12V

16 - LIGHT GROUP 2 12V 15A OUT

15 - LIGHT GROUP 2 GND

14 - LIGHT GROUP 2 12V 15A IN

13 - LIGHT GROUP 2 SWITCH INPUT 12V

32 - SECURITY LIGHT 12V 15A OUT

31 - SECURITY LIGHT GND

30 - SECURITY LIGHT 12V 15A IN

29 - SECURITY SWITCH INPUT 12V

85 - 12V OUT 30 AMP (SLIDE#1)

84 - GND OUT (SLIDE#1)

83 - 12V OUT 30 AMP (SLIDE#2)

82 - GND OUT (SLIDE#2)

81 - 12V OUT 30 AMP (SLIDE#3)

80 - GND OUT (SLIDE#3)

79 - 12V OUT 30 AMP (SLIDE#4)

78 - GND OUT (SLIDE#4)

77 - 12V OUT 30 AMP (SLIDE#5)

76 - GND OUT (SLIDE#5)

64 - AWNING LIGHT GND

63 - AWNING LIGHT 12V 5A OUT

62 - AWNING SWITCH INPUT 12V

71 - 12V OUT 15 AMP (AWNING#1)

70 - GND OUT (AWNING#1)

69 - 12V OUT 15 AMP (AWNING#2)

68 - GND OUT (AWNING#2)

90 - +12VDC IN POWER HOUSE

89 - 12V IN 30 AMP SLIDE & JACK POWER

88 - 12V IN 15 AMP AWNING POWER

87 - +12VDC IN POWER CHASSIS

86 - GROUND IN

1 2 3 4 5 6 7 8

DETAIL F

33 3 4 3 5 36 3 7 3 8 39 4 0 41 4 2 4 3 44 4 5 4 6 47 4 8 49 5 0 5 1 52 5 3 5 4 55 5 6 57 5 8 5 9 60 6 1

92 9 1 96 9 5

94 9 3 98 9 7

10 0 9 9

67 - WATER PUMP +12V IN 10A

66 - WATER PUMP GND

65 - WATER PUMP +12V OUT 10A

75 - 12V OUT 30 AMP (FRONT JACKS)

74 - GND OUT (FRONT JACKS)

73 - 12V OUT 30 AMP (REAR JACKS)

72 - GND OUT (REAR JACKS)

Reset Button

DETAIL H

End of Line terminator resister.

• WIRING

The Wiring Diagram Depicts

All The Wiring Connections

Required For Proper Operation

Of The Unit.

Body Control Module (BCM)

Connections

• RV-C SYSTEM LAYOUT

End of Line terminator resister.

NCSP3CM

• SETUP MENU LIST

Triggers

Trigger 1 No, Momentary , Latch

Trigger 2 No, Momentary , Latch

Trigger 3 No, Momentary , Latch

Trigger 4 No, Momentary , Latch

Jacks

Front Up, Down

Rear Up, Down

Generator

Prime, Start, Manual

Schedule Start time, Stop time

HVAC (Zone1, Zone2, Zone3)

Mode On, Off, Fan, Cool, Heat, Auto

Vent Open, Shut

Vent Fan Off, Low, Medium, High

Schedule Start time, Stop time

Awnings

Awning Light No, Yes

Awning 1 In, Out

Awning 2 In, Out

Slides

Hydraulic In, Out

Slide 1 In, Out

Slide 2 In, Out

Slide 3 In, Out

Slide 4 In, Out

Slide 5 In, Out

Lights

Light Group 1 No, Yes

Light Group 2 No, Yes

Light Group 3 No, Yes

Light Group 4 No, Yes

Awning Light No, Yes

Dimmer Light 1 No, Yes

Dimmer Light 2 No, Yes

Dimmer Light 3 No, Yes

Settings

Bluetooth Scan

Wi-Fi On, Off, Scan, Add,

Clear Account

Date & time Edit

Edit

Alarms,Awnings,

Generator,Triggers,

Lights, Slides

Passcode Setting

Brightness Up, Down

Calibration Set

Reset Floor plan OEM Floor Plan ,

Default Floor Plan

Information Information notes

Software DC,App,BCM, OTA,

Floor plan

Global Connect Login, Show Passcode,

Clear Account

Administration

App Data, Generator

Hour Meter, Log File,

Tanks

Language English, French

Hitch

NCSP3CM

• TRAVEL LOCKOUT (Safety)

iN-Command is equipped with a Travel Lockout feature to ensure

certain system functions are unavailable during transit.

When the Brake Signal (Towable) or Ignition (Motorized) is activated,

the iN-Command will lock down all motorized functions. The Display

Commander (DC) and mobile devices will also display “Travel Lock

Engaged” and the affected buttons will cease to activate.

The lights, water pump, water heater, generator and tanks sensors

will continue to function.

To turn the Travel Lock off, press "Disengage" on the Display

Commander (DC), inside the RV, once the brake signal has been

removed.

Indice

Altri manuali IN-COMMAND Strumento di misura

IN-COMMAND

IN-COMMAND NCSP3 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente