Intel D845PEBT2 Manuale utente

C13230-002

Intel®Desktop Board D845PEBT2

Quick Reference

This guide is written for technically qualified personnel with experience

installing and configuring desktop boards.

Before You Begin

Warning and Cautions......................................................................... 3

Safety and Regulatory Notice ............................................................. 3

Desktop Board Components ....................................................... 4

Supported Components

Processors ........................................................................................... 5

Memory Module Requirements........................................................... 5

Installation Steps

1Installing the I/O Shield ................................................................ 6

2Installing the Desktop Board......................................................... 7

3Installing the Processor ................................................................. 7

4Installing Memory Modules.......................................................... 8

5Installing an AGP Card................................................................. 9

6Installing the Rear Panel USB 2.0 Adapter .................................. 10

7Attaching IDE Drives................................................................... 11

8Attaching Serial ATA (SATA) Drives......................................... 12

9Configuring SATA RAID............................................................ 13

10 Loading the SATA RAID or SATA Driver ................................. 13

11 Connecting Fans........................................................................... 14

12 Connecting Power Cables ............................................................ 14

13 Back Panel Connectors ................................................................ 15

Using the BIOS Setup Program................................................. 16

Setting the BIOS Configuration Jumper Block................. 16

Troubleshooting ................................................................................ 17

Customer Support Links............................................................... 18

Items on the Intel®Express Installer CD-ROM

• Product warranty

• Intel Express Installer

• Intel®Desktop Board D845PEBT2 Product Guide

• Software utilities and drivers

• Software license agreement

• Readme file

2 Intel Desktop Board D845PEBT2 Quick Reference

INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH

INTEL®PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL

OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED

BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL’S TERMS AND

CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO

LIABILITY WHATSOEVER, AND INTEL DISCLAIMS ANY EXPRESS OR

IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL

PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO

FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR

INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL

PROPERTY RIGHT. INTEL PRODUCTS ARE NOT INTENDED FOR USE IN

MEDICAL, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS. INTEL MAY

MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT

ANY TIME, WITHOUT NOTICE.

Intel Desktop Board D845PEBT2 may contain design defects or errors known as

errata which may cause the product to deviate from published specifications.

Current characterized errata are available on request.

Contact your local Intel sales office or your distributor to obtain the latest

specifications and before placing your product order.

Copies of documents which have an ordering number and are referenced in this

document, or other Intel literature, may be obtained from Intel Corporation by

going to the World Wide Web site at: http://www.intel.com or by calling

1-800-548-4725.

Intel, Celeron, and Pentium are registered trademarks of Intel Corporation or its

subsidiaries in the United States and other countries.

†Other names and brands may be claimed as the property of others.

Intel Desktop Board D845PEBT2 Quick Reference 3

Before You Begin

Warning and Cautions

WARNING

Disconnect the desktop board’s power supply from its AC power

source before you connect or disconnect cables, or install or remove

any board components. Failure to do this can result in personal

injury or equipment damage. Some circuitry on the desktop board

can continue to operate even though the front panel power switch

is off.

CAUTION

Electrostatic discharge (ESD) can damage desktop board components.

Install the board at an ESD-controlled workstation. If such a workstation

is not available, wear an antistatic wrist strap or touch the surface of the

antistatic package before handling the board.

CAUTION

Many of the midboard and front panel connectors provide operating

voltage (+5 V DC and +12 V DC, for example) to devices inside the

computer chassis, such as fans and internal peripherals. These

connectors are not overcurrent protected. Do not use these connectors

for powering devices external to the computer chassis. A fault in the load

presented by the external devices could cause damage to the computer,

the interconnecting cables, and the external devices themselves.

Safety and Regulatory Notice

See the Intel Desktop Board D845PEBT2 Product Guide for all applicable

regulatory compliance statements, product certification markings, and safety and

electromagnetic compatibility (EMC) standards and regulations the desktop

board is compliant with.

Replacement battery warning label provided: Place the label inside the chassis

in an easy-to-see location near the battery but not on the board itself.

Intended uses: This product was evaluated as information technology

equipment (ITE) for home or office use when installed into an appropriate

computer chassis. Other end uses or locations may require further evaluation.

4 Intel Desktop Board D845PEBT2 Quick Reference

Desktop Board Components

OM14802

2-pin alternate

power/sleep LED

connector

JKL

PQR

Reset

HD LED

Power LED

No Connection

A Front panel audio connector N BIOS configuration jumper block

B CD-ROM connector (ATAPI-style) O SCSI hard drive activity LED

connector

C Back panel connectors P Speaker

D 12 V processor core voltage connector Q Front chassis fan connector

E Rear chassis fan connector R Secondary Serial ATA connector

F Intel®82845PE (MCH) S Primary Serial ATA connector

G Processor socket T Chassis intrusion connector

H Processor fan connector U Intel®82801DB (ICH4)

I DIMM sockets V Front panel USB 2.0 connector

J Main power connector W Battery

K Secondary IDE connector X AGP connector

L Primary IDE connector Y PCI bus add-in card connectors

M Diskette drive connector

Intel Desktop Board D845PEBT2 Quick Reference 5

Supported Components

Processors

The board supports a single processor with the following features:

Type

Designation

Front Side Bus

Frequency

L2 Cache

2.8, 2.66, 2.53,

2.4B, and

2.26 GHz

533 MHz 512 KB

Intel®Pentium®4 processor

on .13 micron process in an

mPGA478 package

2.6, 2.5, 2.40,

2.20, 2A, 1.80A,

and 1.60A GHz

400 MHz 512 KB

Intel Pentium 4 processor on

.18 micron process in an

mPGA478 package

2, 1.90, 1.80,

1.70, 1.60, 1.50,

and 1.4 GHz

400 MHz 256 KB

Intel®Celeron®processor in

an mPGA478 package

1.8 and 1.7 GHz 400 MHz 128 KB

For the latest information on processors supported by Desktop Board

D845PEBT2, refer to the Intel World Wide Web site at:

http://support.intel.com/support/motherboards/desktop

Memory Module Requirements

Desktop Board D845PEBT2 supports system memory as defined below:

• Up to two 184-pin Double Data Rate (DDR) SDRAM Dual Inline Memory

Modules (DIMMs) with gold-plated contacts. Supported memory

configuration are:

—DDR333: to run DDR333 memory at full speed requires an Intel

Pentium 4 processor with 533 MHz front side bus frequency (FSB).

DDR333 memory will run only at DDR266 speeds when using a

processor with 400 MHz FSB.

—DDR266: requires an Intel Pentium 4 processor with 533/400 MHz

FSB, or Intel Celeron processor with 400 MHz FSB.

• Unbuffered and non-registered single or double-sided DIMMs

• Serial Presence Detect (SPD) memory only

• Non-ECC RAM (ECC memory will run in non-ECC mode)

• 2.5 V memory

6 Intel Desktop Board D845PEBT2 Quick Reference

✏NOTES

Desktop Board D845PEBT2 has been designed to support DIMMs based

on 512 Mbit technology up to 2 GB, but this technology has not been

validated on this board.

All memory components and DIMMs used with the desktop board must

comply with the PC SDRAM specifications. These include the PC

SDRAM Specification (memory component specific), the PC Unbuffered

DIMM Specification. To view or download these specifications, refer to

this Intel World Wide Web site:

http://www.intel.com/technology/memory/pcsdram/

For information about vendors that support these memory requirements,

refer to the Desktop Board D845PEBT2 link on this Intel World Wide

Web site:

http://support.intel.com/support/motherboards/desktop/

Installation Steps

1 Installing the I/O Shield

The board comes with an I/O shield that is used to block radio frequency

transmissions, necessary to pass emissions (EMI) certification testing, protect

internal components from dust and foreign objects, and promote correct airflow

within the chassis.

Install the I/O shield before installing the board in the chassis. Place the shield

inside the chassis as shown in the following figure. Press the shield into place so

that it fits tightly and securely. If the shield doesn’t fit, obtain a properly sized

shield from the chassis supplier.

OM14811

Intel Desktop Board D845PEBT2 Quick Reference 7

2 Installing the Desktop Board

Refer to your chassis manual for specific instructions on installing and removing

the desktop board.

Secure Desktop Board D845PEBT2 to the chassis using the eight screws. Refer

to the board illustration on page 4 for the location of the mounting screw holes.

3 Installing the Processor

To install the processor, follow these steps

1. Observe the precautions in “Before You Begin”on page 3.

2. Lift the processor socket lever.

3. Install the processor so that the corner with the triangle marking (A) is

aligned with the corner where the lever is attached to the socket.

4. Lower the lever back to its original position.

OM12078

mPGA478B

5. The desktop board has an integrated processor fan heat sink retention

mechanism (RM). For instructions on how to install the processor fan heat

sink, refer to the boxed processor manual or the Intel World Wide Web

site at:

http://support.intel.com/support/processors/pentium4/intnotes478.htm

8 Intel Desktop Board D845PEBT2 Quick Reference

4 Installing Memory Modules

CAUTION

Install memory in the DIMM sockets prior to installing the AGP video card

to avoid interference with the memory retention mechanism.

Desktop Board D845PEBT2’s two DIMM sockets are arranged as DIMM 0 and

DIMM 1, as shown in the following figure. If installing a single DIMM, install

it in DIMM 0.

To install DIMMs, follow these steps:

1. Observe the precautions in “Before You Begin”on page 3.

2. Remove the AGP video card if it interferes with the DIMM clips from

being easily opened and closed.

3. Align the small notch at the bottom edge of the DIMM with the key in the

socket.

4. Insert the bottom edge of the DIMM into the socket.

5. Push down on the top edge of the DIMM until the retaining clips snap into

place. Make sure the clips are firmly in place.

OM14803

DIMM 0

DIMM 1

Intel Desktop Board D845PEBT2 Quick Reference 9

5 Installing an AGP Card

CAUTION

Care must be taken when installing an AGP card into an AGP slot.

When installing any AGP card in the desktop board, ensure that it is fully

seated in the AGP connector before you power on the system. If the card

is not fully seated in the AGP connector, an electrical short may result

across the AGP slot pins. Depending on the over-current protection of the

power supply, certain board components and/or traces may be damaged.

✏ NOTE

The D845PEBT2 board is only compatible with 1.5 V AGP cards.

Desktop Board D845PEBT2 has an integrated AGP card retention mechanism

(RM). Follow these instructions to install an AGP card:

1. Observe the precautions in “Before You Begin”on page 3.

2. Place the AGP card in the AGP connector.

3. Press down on the card until it is completely seated in the connector and the

card retention notch snaps into place below the RM.

4. Secure the card’s metal bracket to the chassis back panel with a screw.

Install PCI cards into the PCI bus add-in card connectors on the desktop board.

OM14695

To remove the AGP card, reverse steps taken when installing an AGP card.

Before removing the card, make sure to push back on the RM lever (A) until the

retention pin completely clears the notch in the card.

10 Intel Desktop Board D845PEBT2 Quick Reference

6 Installing the Rear Panel USB 2.0 Adapter

The Intel®boxed desktop board package includes a USB 2.0 adapter. Follow

these instructions to install the rear panel USB 2.0 adapter:

1. Observe the precautions in “Before You Begin”on page 3.

2. Attach the cable end with the connector to the front panel USB 2.0 header

on the desktop board.

3. Secure the cable’s metal bracket to the chassis back panel with a screw.

OM14822

Altri manuali per D845PEBT2

Indice

Lingue:

Altri manuali Intel Scheda madre

Intel

Intel Desktop Board D845GLVA Manuale utente

Intel

Intel D945GNT Manuale utente

Intel

Intel MI910F Manuale utente

Intel

Intel DG965RY Manuale utente

Intel

Intel D915PLWD Manuale utente

Intel

Intel BOXD850MVSE Manuale utente

Intel

Intel DQ57TM Manuale utente

Intel

Intel DH61AGL Manuale utente

Intel

Intel DH61ZE Manuale utente

Intel

Intel i845-PE Manuale utente

Intel

Intel BOXDG33TLM Guida alla configurazione

Intel

Intel DZ77SL-50K Manuale utente

Intel

Intel D865GBF Manuale utente

Intel

Intel P35 Manuale utente

Intel

Intel BLKD510MO Guida alla configurazione

Intel

Intel DH61KVCH Manuale utente

Intel

Intel BLKDH55HC Manuale utente

Intel

Intel BLKDP67BA Manuale utente

Intel

Intel EMX-965GME Manuale utente

Intel

Intel DH61KVCH Manuale utente

Intel

Intel BLKDG41MJ Guida alla configurazione

Intel

Intel D845GRG Guida

Intel

Intel D510MO Manuale tecnico

Intel

Intel Enpirion EM2130 Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuale utente