Intel ISP1100 - Server Platform - 0 MB RAM Manuale utente
Rail Option Kit Installation Guide
for Intel®ISP1100 Internet Server
The most current version of this document and other documents relating to the
Intel®ISP1100 Internet Server can be found at http://www.intel.com/isp.
Copyright © 2000 Intel Corporation.All rights reserved. No part of this document
may be copied, or reproduced in any form, or by any means without prior written
consent of Intel.
Intel Corporation (Intel) makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and fitness for a
particular purpose. Intel assumes no responsibility for any errors that may appear in
this document. Intel makes no commitment to update nor to keep current the informa-
tion contained in this document.
† Third-party brands and trademarks are the property of their respective owners.
February 29, 2000
Revision 1.0
Document Number:A17803-001
Intel ISP1100 Internet Server Rail Kit 1
Introduction
This document explains how to install the Intel ISP1100 Internet Server in a four post
rack with sliding rails.
Before you begin:
1. Make sure you have the following parts:
• Two (2) rail assemblies
• Two (2) front brackets (short)
• Two (2) rear brackets (long)
• Ten (10) 10/24 x 0.25” panhead phillips screws to attach the chassis sections
to the server
• Ten (10) 8/32 x 0.38” flathead countersunk phillips screws to attach the
brackets to rack sections; also includes (10) sets of lock washers, washers,
and nuts
2. Make sure you have the following tools:
• A phillips (cross-head) screwdriver
• An 11/32” nut driver
3. Read the safety and warnings information in the Intel®ISP1100 Internet Server
Quick Start Guide.
Note: Theslidesincludedinthiskitareratedfor50poundsofloadperpairof
slidesforgeneralusefor10,000cyclesofopening and closing. Higher
cyclesorfrequencywilllowertheloadrating.Low-cycle applications will
allow an increase in load rating. A load ratio of 2:1 can be applied to all
slidesasaproofload.Thisproofloadis for static test only when the slide
isinthefullyopenpositionandnottobecycled.Intheclosedposition,
theslidecanacceptupto five times the slide load rating. The load rating
onlyapplieswhentheslidesaremountedtothesidesofthechassis.
4. Make sure the server is turned off and is not plugged in to an electrical
outlet.
Intel ISP1100 Internet Server Rail Kit2
Remove Chassis Sections from Rail Assemblies
For each rail assembly:
1. Slide the rack section (A) out of the slider section (B) until it locks.
2. Slide the chassis section (C) out of the slider section until it locks, then press the
lock arm (D) on the chassis section to release it from the slider section.
3. Pull the chassis section out of the slider section.
C
AB
OM09755A
D
Intel ISP1100 Internet Server Rail Kit 3
Attach the Chassis Sections to the Server
On each side of the server:
1. Align the holes in the chassis section (A) with the holes in the server. Do not use
the front hole on the server.
2. Fasten the chassis section to side of the server with four 10/24 x 0.25” panhead
phillips screws (B).
A
B
OMO9763
Intel ISP1100 Internet Server Rail Kit
Attach the Brackets to the Rail Assemblies
The brackets attach to the rack sections of the rail assemblies and then to the rack.
Each rail assembly needs a front and a rear bracket.
Attaching the Front Bracket
1. Slide the rack section so the screw holes show through the rectangular opening
(A) in the slider section (B).
2. Place the front bracket (C) against the rack section as shown.
3. Line up the slot in the bracket with the holes in the rack section.
4. Fasten the front bracket to rack section with two 8/32 x 0.38” flathead counter-
sunk phillips screws (D). Each screw takes a regular washer, a lock washer and a
nut (E). Put the washers and nut on in the order shown.
C
E
D
B
OM09761
A
Attaching the Rear Bracket
There are two steps to attaching the rear bracket:
1. Determine where to attach the bracket.
The bracket attaches to the back end of the rack section. However, the exact
placement depends on the depth of your rack. Because the rack section is a fixed
length, you use the bracket placement to set the rail assembly length so the rail
assembly fits your rack.
4
Intel ISP1100 Internet Server Rail Kit 5
You set the length by choosing which of the bracket’s slots to use, and by sliding
the bracket in or out.
• Hold the rail assembly in the rack to determine which slots to use in the
bracket, and to determine the rail assembly length.
• Loosely attach the bracket to the rack section of the rail assembly.
Use two 8/32 x 0.38” flathead countersunk phillips screws (C). Each screw
requires a regular washer, a lock washer and a nut, added in the order shown
(D). Spread the screws as far apart on the rail assembly as you can to
distribute the load.You may also use the extra screw provided, but it is not
necessary.
Attach the bracket loosely enough so it can slide against the rack section. This
allows you to adjust the length of the rail assembly to fit your rack.
2. Fasten the bracket to the rail assembly.
Tighten the screws holding the rear bracket to the rack section. Be careful not to
move the rear bracket while you are tightening the screws.
A
B
C
D
OM09740
Intel ISP1100 Internet Server Rail Kit
Install the Assembled Rails in the Rack
For each assembled rail:
1. Fasten the front bracket to the rack using two screws (A) provided with the rack.
A
OM09756A
2. Fasten the rear bracket to the rack with two screws (A) provided with the rack.
A
OM09756B
6
Intel ISP1100 Internet Server Rail Kit
Put the Server Into the Rack
1. Hold the server so the front is facing you. Line up the server so the rollers on the
chassis section (A) go into the channel (B) of the slider section of the rail
assembly.
2. Gently slide the server into the rack, making sure that all the rollers go into the
channel.
AB
A
OM09754
3. Use the bolts provided with the rack to fasten the server’s front flanges (A) to the
rack.
AA
OM09758
7
Intel ISP1100 Internet Server Rail Kit
Removing the Server From the Rack
If you need to remove the server from the rack:
1. Unbolt the server’s front flanges (A) from the rack.
AA
OM09758B
2. Slide the server out of the rack as far as you can. When the rail assembly locks,
press the lock arm (A) on both sides to release the server.
A
OM09762
3. Remove the server from the rack.
8
Altri manuali per ISP1100 - Server Platform - 0 MB RAM
5
Indice
Altri manuali Intel Server
Intel
Intel MFSYS25 - AXXPSU 1000W Power Supply Module Manuale utente
Intel
Intel SRKA4 - Server Platform - 0 MB RAM Manuale utente
Intel
Intel P4308CP4MHEN Manuale utente
Intel
Intel M50CYP2UR Series Guida rapida alla configurazione
Intel
Intel R1000EP series Manuale utente
Intel
Intel MFSYS25V2 Manuale utente
Intel
Intel SR1670HV - Server System - 0 MB RAM Manuale utente
Intel
Intel H2312JFJR Manuale utente
Intel
Intel S7000FC4UR - Server System - 0 MB RAM Manuale utente
Intel
Intel R1000WF Series Guida rapida alla configurazione
Intel
Intel S2600CP Family Manuale utente
Intel
Intel SR1530AHLX - Server System - 0 MB RAM Manuale utente
Intel
Intel M50FCP1UR Manuale utente
Intel
Intel M50CYP1UR Series Manuale utente
Intel
Intel TIGI2U - Carrier Grade Server Manuale utente
Intel
Intel R2000GZ series Manuale utente
Intel
Intel SR2625UR - Server System - 0 MB RAM Manuale utente
Intel
Intel SR1530HSH - Server System - 0 MB RAM Manuale utente
Intel
Intel P4000IP Series Manuale utente
Intel
Intel AD450NX Manuale utente
