Intel P4000RP Manuale utente
Thank you for buying an Intel® Server System. The following information will help you
assemble your Intel®Server System and install components.
If you are not familiar with ESD [Electrostatic Discharge] procedures used during
system integration, see the complete ESD procedures described in your Service Guide.
This guide and other supporting documents are located on the web at:
http://www.intel.com/p/en_US/support.
Intel® Server System P4000RP Family
Quick Installation User's Guide
G85600-002
(This page is intentionally left blank.)
i
Table of Contents
General Installation Process ........................................................................................................ 3
System Overview .............................................................................................................................. 1
Preparing the System ....................................................................................................... 3
Remove the Side Cover ................................................................................................... 3
Install the Processor ....................................................................................................... 3
Install Active Heat Sink .................................................................................................... 4
Install DIMM Memory Modules ..................................................................................... 5
Install Tool-less CD-ROM or DVD-ROM Drive ........................................................ 6
Install Hard Drive ................................................................................................................. 6
Install PCI-e Card Assembly ........................................................................................... 7
Install Intel® Remote Management Module 4 NIC (optional) ....................... 7
Install RMM4 EMI Cover (optional) ............................................................................. 8
Install Alternate Serial Port (optional) ..................................................................... 8
Install Intel® RAID Smart Battery (optional) ...................................................... 9
Install Second Power Supply Module (optional) .............................................. 9
Install Side Cover .................................................................................................................. 9
Finishing Up ............................................................................................................................. 9
Install Software ................................................................................................................. 10
HDD Cage Cable Connection ...................................................................................... 11
Front Panel Controls and Indicators ...................................................................... 12
Cable Routing Diagram .................................................................................................. 12
Reference ............................................................................................................................................ 11
ii
Warning
Read all caution and safety
statements in this document
before performing any of the
instructions. Also see the Intel
®
Server Board and Server Chassis
Safety Information document at:
http://www.intel.com/support/
motherboards/server/sb/cs-010770
.htm for complete safety information.
Installation and service
of this product to be
performed only by
qualified service personnel
to avoid risk of injury from
electrical shock or energy
hazard.
Warning Caution
Observe normal ESD
[Electrostatic Discharge]
procedures during system
integration to avoid possible
damage to server board and/or
other components.
Tools Required
Anti-static
wrist strap
Phillips*
screwdriver
Flat Blade
screwdriver
Intel®is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as
the property of others. Copyright © 2013, Intel Corporation. All rights reserved.
Thermal Operation and Configuration Requirements
To keep the system operating within supported maximum thermal limits, the system must meet the following operating and configuration
guidelines:
• Ambient in-let temperature cannot exceed 35º C and should not remain at this maximum level for long periods of time. Doing so
may affect long term reliability of the system.
•DIMM Population on CPU: Install DIMMs in order; Channels A, and B. Start with 1st DIMM slot (blue) on each
channel.
•All hard drive bays must be populated. Hard drive carriers either can be populated with a hard drive or supplied drive blank.
•In single power supply configurations, the second power supply bay must have the supplied filler blank installed at all times.
• The system top-cover must be installed at all times.
1
System Overview
Intel® Server System P4308RPLSHDR
B
A
C
D
E
J
K
L
M
N
F
G
H
IO
System Features and Components
460W Hot Swap Power Supply (Two)
I/O Ports
A Kensington* Cable Lock Mounting Hole
PCI Add-in Board Slot Covers
AC Input Power Connector (Two)
Alternate Serial Port Knockout
RMM4 Knockout
Padlock Loop
Alternate RMM4 Knockout
Active Heatsink
5.25" Peripheral Bays
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Front Control Panel
8 x 3.5" Hot-swap HDD Cage
System Fan
Server Board
2
System Overview
0123
4567
Hot Swap Hard Drive
Bay Options and
HDD Numbering
8 x 3.5" Hot-Swap Drive Cage
A
A
3
General Installation Process
The installation instructions in this section are for general components of Intel® Server System
P4000RP family.
Minimum Hardware Requirements
■ Processor
■ Heat Sink
■ Memory
■ Hard Disk Drives
■ Power
To avoid integration difficulties and possible damage to your system,
make sure you have components from each category below.
1
Preparing the System
Observe normal ESD (Electrostatic Discharge) procedures.
Place your Intel®Server System on a flat anti-static
surface to perform the following integration procedures.
Observe ESD procedures before reaching inside to make
server board connections or install components.
B
A
A
Remove the Side Cover
B
Remove the screws.
A
NOTE:
A non-skid surface or a stop behind the chassis may be needed to prevent the
chassis from sliding on your work surface.
Slide the side cover back and lift the cover outward to remove it.
2
3Install the Processor
Cautions:
When removing the protective
cover, DO NOT TOUCH the
gold socket pins.
A
When unpacking a processor,
hold by the edges only to avoid
touching the gold contact pins.
C
To avoid damage, DO NOT
DROP the cover onto the
socket pins or components.
B
A. Open the Socket Lever
Push the lever
handle
down
and away
from the socket
to release it.
Rotate the lever
open all the way.
A
B
A
B. Open the Load Plate
C. Unpack the Processor
Open the load
plate as shown.
Carefully remove
protective cover
as shown.
Save the
protective
cover.
4
General Installation Process
A
B
Install the Processor ... continued
Components
CAUTION: The underside of the processor has components
that may damage the socket wires if installed improperly.
Processor must align correctly with the socket opening
before installation.
DO NOT DROP processor into socket!
Orient the processor with the socket
so that the processor cutouts match
the two socket pins.
A
Note location of gold key at
corner of processor.
B
D.
Install the Processor
Carefully lower the load plate
over the processor.
E. Close the Load Plate
Carefully lower the load plate
over the processor.
A
B
Make sure the front edge
of the load plate slides
under the shoulder screw
as the lever is lowered.
Close the load
plate locking
lever.
A
Load Plate
Front Edge
Shoulder
Screw
F. Engage the Load Plate
A
B
Push down on the locking lever.
Slide the tip of
the lever under
the notch in the
load plate. Make sure the
lever is securely latched.
CAUTION: DO NOT damage the
server board with the tip of the
locking lever.
Save the
protective
cover.
A
A
A
B
H.
Remove the Cover
Carefully lift the cover straight up
as shown.
G. Latch the Locking Lever
4Install Active Heat Sink
A
Align heat sink with holes
in board and lower assembly
to board. Snaps go through
holes in server board.
B
Press downward
on top of cap.
C
Plug the fan cable into the CPU fan header.
E
Fastener snaps
into final position.
D
Repeat B-D for each
fastener in the numerical
order shown at left.
Make sure the screwdriver slot at
the top of each fastener is rotated
perpendicular to the blades of
the heat sink as shown.
Use the following procedure to install an
active heat sink to your server board:
CAUTION: The heat sink has
thermal interface material (TIM) on
the underside of it. Use caution so
that you do not damage the thermal
interface material. Use gloves to
avoid sharp edges.
Note: Heatsink
styles may vary
2
3
1
4
TIM
A
E
5
General Installation Process
A
C
DB
E
Other
Memory
DDR3
5Install DIMM Memory Modules To Install DIMMs:
DDR3L DIMM Memory Identification:
Open both DIMM socket levers.
C
A
D
E
Note location of alignment notch.
B
DIMM
notch and
socket
bump must
align as
shown.
This server board supports up to 4 DDR3L 1333/1600 ECC UDIMM.
Non-ECC memory is NOT supported by this server board.
CAUTION: Observe normal ESD (ElectroStatic Discharge) procedures
to avoid possible damage to system components.
Insert DIMM making sure the connector edge of the DIMM aligns correctly with the slot.
Push down firmly on the DIMM until it snaps into place and both levers close.
IMPORTANT! Visually check that each latch is fully closed
and correctly engaged with each DIMM edge slot.
CAUTION: Avoid touching contacts when handling or installing DIMMs.
Install DIMM Memory Modules... Continued
Intel®Server Board S1200V3RPL
Note: For additional memory configurations, see the Service Guide on the
Intel®Server Deployment & Management DVD that accompanied
your Intel®Server System, or go to:
http://www.intel.com/p/en_US/support/ (post-production)
Memory sizing and configuration is supported only for qualified DIMMs approved by
Intel®. For a list of supported memory, go to:
http://serverconfigurator.intel.com/sct_app.aspx (post-production)
For the best performance, a minimum of two DIMMs is recommended, populated
in the blue slot of each memory channel.
DIMM_A2
DIMM_A1
DIMM_B2
DIMM_B1
CPU Socket
6
General Installation Process
B
A
3.5" Hot-Swap Hard Drive Carrier
A
Open the Hot-swap door and
remove the drive carrier by
pressing the green button and
opening the lever.
Slide the carrier out.
B
Remove the four screws securing the
HDD interface bracket and remove the
HDD interface bracket.
C
Install the hard disk drive using the same four
screws as shown. Make sure the connector
end of the drive matches the backplane
connector.
D
CAUTION: If you don’t install all drives,
empty drive bays must be occupied by
carriers with plastic drive blank
provided to maintain proper system cooling.
With the lever open, insert the
hard disk drive assembly into the
cage opening and push until the
locking lever engaged.
Push in the lever to lock it into
place, then close the door.
E
F
TOP
BREAK OFF TAB
BEFORE MOUTING
2.5´´ HARD DRIVE
C
3.5´´ HDD
D
7Install Hard Drive
E
F
6Install Tool-less CD-ROM or DVD-ROM Drive
C
Attach slides to the DVD or CD-ROM drive
by pressing the slides firmly into the side
dimples on the DVD or CD-ROM drive.
B
Get the slides from the
chassis side.
D
Insert the drive/slide assembly
into the device bay until the
slides lock into place.
A
Press the release latch and use
the finger holes to Pull out the
EMI shield.
Finger Holes
AD
B
C
Indice
Altri manuali Intel Server
Intel
Intel SR2600UR - Server System - 0 MB RAM Manuale utente
Intel
Intel R1000GZ Guida alla configurazione
Intel
Intel SBX82 - Server Compute Blade Manuale utente
Intel
Intel R1000EP series Manuale utente
Intel
Intel SRPM8 Manuale utente
Intel
Intel SC5650HCBRP Manuale utente
Intel
Intel TIGPT1U - Carrier Grade Server Manuale utente
Intel
Intel SR6850HW4S Manuale utente
Intel
Intel SR1560SF - Server System - 0 MB RAM Manuale utente
Intel
Intel SERVER SYSTEM SR2500AL Manuale utente
Intel
Intel MFSYS35 Manuale utente
Intel
Intel SR1600UR - Server System - 0 MB RAM Manuale utente
Intel
Intel SPSH4 - Server Platform - 0 MB RAM Guida alla configurazione
Intel
Intel S2600WF Series Guida alla configurazione
Intel
Intel A1U2ULCP Guida alla configurazione
Intel
Intel S9200WK Series Manuale utente
Intel
Intel SR1680MV - Server System - 0 MB RAM Manuale utente
Intel
Intel IP Media Server Manuale utente
Intel
Intel R1304BTSSFAN Manuale utente
Intel
Intel SR870BH2 - Server Platform - 0 MB RAM Manuale utente
