Intellitec iConnex Manuale utente
Page 1
USER MANUAL
V2.0 08/10/21
Technical Helpline
+44 (0) 151 482 8970
www.intellitecmv.com
E
11 10R05/01 11558
E
11 10R05/01 11558
DATA
Page 2
CONTENTS
Product Specification
Installation - Schematic
Installation - Connector Plug Wiring
Diagnostic Display 1
Diagnostic Display 2
Graphical User Interface
Module Addressing
Module Programming
CAN-Bus Termination Resistor Jumpers
Keypad Addressing
Installation Expansion
Keypad Features
OLED Series Keypads
Temperature Sensor
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Copyright © 2019 Intellitec MV Ltd
The instructions within this booklet (User’s Manual) must be read thoroughly before
any installation work, testing or general use.
We recommend this booklet is kept in a safe place that can be easily retrieved for any
future referral.
Installation must be carried out by competent personnel with adequate knowledge of
electrical installations.
All necessary precautions must be taken to ensure this product is fitted correctly,
securely and safely into the desired application.
This product must not interfere with road safety or OEM safety systems fitted to the vehicle
All necessary checks must be carried out by installer to ensure this device is used only in the
intended application and also does not conflict with any road laws in all countries the vehicle
may be driven within.
Intellitec MV Ltd reserves the right to update this document (User’s Manual) without
notification at any time.
You will find the latest documents for our products on our website:
www.intellitecmv.com
Page 3
PRODUCT
SPECIFICATION
Input Voltage (Volts DC)
Max Input Current (A)
Standby Current Consumption (mA)
IP Rating of iConnex module
Weight (g)
Dimensions L x W x D (mm)
9-32
50
Ip20
367g
135x165x49
INPUTS OUTPUTS
6x Digital (Pos/Neg Configurable)
2x Voltage Sense (Analog)
1x Temperature Sense
1x External CAN-Bus
9x 8A Positive FET w/auto shutdown
1x 1A Negative FET w/auto shutdown
2x 30A Relay Dry Contacts (COM/NC/NO)
CAN-Bus Baud Rates
50 Kbits/s
83.33 Kbits/s
100 Kbits/s
125 Kbits/s
250 Kbits/s
500 Kbits/s
19 mA
29 mA
Sleepmode Current Consumption (mA)
Page 4
INSTALLATION
Schematic:
87
87A
30
87
87A
30
30A
30A
2mm Positive Supply
2mm Positive Supply
Relay 11 Normally Open
Relay 12 Normally Open
50A
10mm Positive Supply
Input Connector
Output Connector
Auxiliary Connector
Keypad Connector
Page 5
INSTALLATION
Connector Plug Wiring:
Keypad Connector
Auxiliary Connector
Output Connector
Input Connector
12 11 10 9 8 7
6 5 4 3 2 1
10 9 8 7 6
5 4 3 2 1
8 7 6 5
4 3 2 1
6 5 4
3 2 1
Cable Entry View
Cable Entry View
Cable Entry View
Cable Entry View
1. Output 10 Negative (1A max).
2. Output 9 Positive (8A max).
3. Speaker + Output (smart model only).
4. Output 8 Positive (8A max).
5. Speaker - Output (smart model only).
6. Output 7 Positive (8A max).
7. Output 1 Positive (8A max).
8. Output 2 Positive (8A max).
9. Output 3 Positive (8A max).
10. Output 4 Positive (8A max).
11. Output 5 Positive (8A max).
12. Output 6 Positive (8A max).
1. Input 6 (Hi/Lo configurable).
2. 0V (Ground) to chassis negative.
3. 0V (Ground) to chassis negative.
4. 0V (Ground) to chassis negative.
5. 0V (Ground) to chassis negative.
6. Input 5 (Hi/Lo configurable).
7. Input 4 (Hi/Lo configurable).
8. Input 3 (Hi/Lo configurable).
9. Input 2 (Hi/Lo configurable).
10. Input 1 (Hi/Lo configurable).
1. Temperature sensor ground.
2. Battery voltage sense 1.
3. Temperature sensor data 2.
4. Battery voltage sense 2.
5. Temperature sensor only 3V3.
6. Temperature sensor data 1.
7. External CAN-Hi (Vehicle Body).
8. External CAN-Lo (Vehicle Body).
1. 0V (Ground) to keypad only.
2. Switch 1 negative return (System wake-up).
3. N/C
4. 5V (Supply) to keypad only.
5. Keypad CAN Hi.
6. Keypad CAN Lo.
Automotive rated 1mm cable must be used with the Molex connectors:
10/6 CTT (Copper Tube Terminal) 531021Power Connection
Molex 10-Way Female Housing 0469921010
Molex 12-Way Female Housing 0469921210
Molex 8-Way Female Housing 0469920810
Molex 6-Way Female Housing 0469920610
Connector Description Manufacturers Part Number
Page 6
DIAGNOSTIC
DISPLAY 1
POWER The POWER diagnostic LED illuminates green when power is active at the module.
It will illuminate red during fault conditions.
DATA The KEYPAD diagnostic LED illuminates green when a keypad is connected to the
module. It will flash blue when any button is pressed on the keypad to show
communications are present.
CAN-BUS The CAN-BUS diagnostic LED illuminates green when there are active
communications to an external CAN-Bus. It will flash blue when it recognises
a monitored message.
INPUTS
1-6
(Digital)
The INPUT 1-6 diagnostic LEDs illuminate green when the corresponding input is
present.
INPUTS
7-8
(Analog)
The INPUT 7 & 8 diagnostic LEDs illuminate green, amber and red to signify the
pre-programmed voltage thresholds of these inputs. This is set in the GUI.
OUTPUTS The OUTPUT diagnostic LEDs illuminate green when the output is active.
If there is a short-circuit on an output, the LED will flash off for 500ms and back on
for 500ms continuously until a module power-cycle. The output will shut down
completely and the green power LED will turn red to indicate a present fault.
If the output is in overload condition (>8A), the output will temporarily shut down and
attempt to turn on 3 times. If the output is still in overload condition, the output will
remain shut down until the logic to activate is cycled. During this period, the power
LED will turn red and the output LED will flash fast.
DATA
Page 7
DIAGNOSTIC
DISPLAY 2
PROGRAMMING
When programming the iConnex, the LEDs on the diagnostic display will change
function to show the status of the programming operation.
The column on output LEDs 1-6 will illuminate green with a single red LED that
flashes vertically to indicate programming mode is active.
The column on output LEDs 7-12 will illuminate green with a single red LED that
flashes vertically when data is being transferred.
After programming is complete, the LEDs will return to normal functionality as
described on page 6 (Diagnostic Display 1).
DATA
Page 8
GUI
iConnex GUI is the utility used to write and upload programs to the module.
It can be downloaded, along with programming device drivers, from our website:
www.intellitecmv.com/pages/downloads
Page 9
Addressing
0
8
C
4
A
2
E
6
B
3
F
7
D
5
9
1
The module can be put into ‘slave’ mode by turning the dial to 1,2,3 or 4. A power cycle is
required to activate these modes.
See below table for active modes:
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Master Module
Slave Module 1
Slave Module 2
Slave Module 3
Slave Module 4
Reserved For Future Use
Reserved For Future Use
Reserved For Future Use
Reserved For Future Use
Reserved For Future Use
Reserved For Future Use
Reserved For Future Use
Reserved For Future Use
Reserved For Future Use
Reserved For Future Use
Reserved For Future Use
Page 10
PROGRAMMING
The module can be programmed using the new USB-B connector. The module will automatically
enter programming mode when the GUI attempts to program the module via this USB connection.
USB-B
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Intellitec Sistema di controllo
