Intermec EasyCoder 501 SA Manuale utente
EasyCoder 501/601
Dual Serial Interface Kit
P/N 1-960345-02
Edition 2
September 1998
Installation Instructions
EasyCoder 501/601 – Installation Instructions
1
DUAL SERIAL INTERFACE KIT
The Serial Interface Board adds two serial communication ports
("uart2:" and "uart3:") to the standard serial communication port
("uart1:").
The printer's software detects when a Serial Interface Board is
installed and adds communication and buffer setup options for the
two additional communication ports.
When a Serial Interface Board is fitted, the following types of
interfaces become available:
"uart1:"
Fittedonprinter'sCPUboard.
RS232C Standard.
RS422or20mACL Option.Additionalcircuits required.
"uart2:"
FittedonSerial Interface Board.
RS232C
"uart3:"
FittedonSerial Interface Board.
RS232C or 20 mA CL Selectedbymeans of strap.
The Dual Serial Interface Kit consists of:
• 1 Serial interface board assy.
• 2 Screws MRX-Z 3 ×6 FZB (not intended for EasyCoder 501/
601)
• Installation Instructions
Introduction
"uart1:"
"uart3:"
"uart2:"
230V
0
Note:
Illustrations show an EasyCoder 501.
The principles for fitting this optional
equipment in an EasyCoder 601 are
exactly the same.
EasyCoder 501/601
Dual Serial Interface Kit
Installation Instructions
Edition 2, September 1998
Part No. 1-960345-02
EasyCoder 501/601 – Installation Instructions
2
Continued!
DUAL SERIAL INTERFACE KIT, cont'd.
Step-by-Step Installation
Instructions
Communication
Port "uart1:"
Cover Plate
Power
Switch
Power Cord
Receptacle
The only tool required is a Torx #T10 screwdriver.
❑Turn off the power and remove the power cord.
❑Remove the communication cable from communication port
"uart1:".
❑Open the right-hand door.
❑Remove the eight Torx screws that hold the cover over the left
part of the printer (see illustration below).
❑Remove the cover.
Screws (4x)
Cover
0
230V
Screws (4x)
EasyCoder 501/601 – Installation Instructions
3
❑Remove the existing cover plate.
❑Make sure that the CPU board is strapped and equipped for the
desired type of communication on "uart1:" (see the EasyCoder
501 or EasyCoder 601 Technical Manual). Once the interface
boardhasbeenfitted,itwillbedifficult toaccesstherearpartof
the CPU board.
❑FittherequiredstrapsontheSerialInterfaceBoardasdescribed
on page 5.
❑Connect the cable from the interface board to connector P-4 at
the bottom rear corner of the CPU board. Be careful so the
interface board and the CPU board do not come in contact with
eachother,whichpossiblymaycausedamageorshort-circuiting.
❑Fit the interface board assembly to the printer's rear plate from
theinsideasillustratedbelowusingthesamescrewsthatheldthe
removed cover plate.
DUAL SERIAL INTERFACE KIT, cont'd.
Step-by-Step Installation
Instructions, cont'd.
Continued!
1
P3
2
3
P6
Connect to P-4
on CPU Board
Rear Plate Serial
Interface Board
"uart3:"
(male DB25
connector)
"uart2:"
(female DB25
connector)
Screw
Screw
EasyCoder 501/601 – Installation Instructions
4
DUAL SERIAL INTERFACE KIT, cont'd.
Continued!
Step-by-Step Installation
Instructions, cont'd. ❑Reassemble the printer in reverse order.
❑Connect the communication cables to their respective connec-
tors. Please refer to page 6 for pinout descriptions.
❑Connect the power cord and turn on the power.
"uart1:"
"uart3:"
Serial Interface
Board Assy.
"uart2:"
230V
0
EasyCoder 501/601 – Installation Instructions
5
1
P3
2
3
P6
DUAL SERIAL INTERFACE KIT, cont'd.
Straps
Thefollowing straps areusedto set upthedesired type ofinterface
on the communication ports "uart2:" and "uart3:".
Communication Port "uart2:"
There are no straps for controlling the RS 232C interface on
"uart2:".
Communication Port "uart3:"
RS 232C:
StrapfittedonP-3betweenpin1–2(rightandmiddlepins)selects
RS 232C.
20 mA Current Loop:
Strap fitted on P-3 between pin 2 – 3 (middle and left pins) selects
20 mA current loop.
External +5V:
External +5V (max. 200 mA) can be made available on pin 16 by
fitting a strap on P-6.
Be careful not to enable this option unintentionally, which may
cause harm to the connected terminal, computer or other device.
"uart3:"
"uart2:"
P-3
P-6
EasyCoder 501/601 – Installation Instructions
6
DUAL SERIAL INTERFACE KIT, cont'd.
Informationinthismanualissubjecttochangewithoutpriornoticeanddoesnotrepresentacommitment
on the part of Intermec Printer AB.
© Copyright Intermec PTC AB, 1998. All rights reserved. Published in Sweden.
EasyCoder is a registered trademark of Intermec Technologies Corp.
Torx is a registered trademark of Camcar Division of Textron Inc.
"uart2:" is a DB25 female connector.
"uart3:" is a DB25 male connector.
The mounting holes are connected to chassis ground.
Connector Configuration
Pin "uart2:" "uart3:" Used for: Remarks
DB25female DB25male "uart2:" "uart3:"
1 GNDC GNDC RS232C RS 232C Cableshield
2 TXDA TXDB RS 232C RS232C Transmitted data fromprinter
3 RXDA RXDB RS232C RS232C Receiveddata toprinter
4 RTSA RTSB RS232C RS 232C RTSfromprinter
5 CTSA CTSB RS232C RS 232C CTStoprinter
6 DSRA DSRB RS232C RS232C DSRto printer
7 GNDI GNDI RS232 C RS 232C Signalground
8 – – – – not used
9 – +20M1 – Currentloop + 20 mA
10 – –20M1 – Currentloop - 20 mA
11 – +TXD – Currentloop TXD +
12 – –TXD – Currentloop TXD –
13 – +20M2 – Currentloop + 20 mA *
14 – –20M2 – Currentloop – 20 mA *
15 – – – – not used
16 – +5VEXT – RS232C/CL + 5V max 200 mA.(if strap fitted on P-6)
17 – – – – not used
18 – +RXD – Currentloop RXD +
19 – – – – not used
20 DTRA DTRB RS 232C RS232C DTRpermanently high
21 – – – – not used
22 – – – – not used
23 – – – – not used
24 – – – – not used
25 – –RXD – Currentloop RXD –
*/.In case of printer being activereceiver.
Altri manuali per EasyCoder 501 SA
6
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Intermec Accessori per stampanti
Intermec
Intermec EasyCoder PD41 Manuale utente
Intermec
Intermec EasyCoder 101 Manuale
Intermec
Intermec 3240 Manuale utente
Intermec
Intermec 4630 Manuale utente
Intermec
Intermec EasyCoder PF4ci Manuale utente
Intermec
Intermec PC43d Manuale utente
Intermec
Intermec EasyCoder PF2i Manuale utente
Intermec
Intermec 3600 Manuale utente
Intermec
Intermec PC43t Manuale utente
Intermec
Intermec PB42 Manuale utente
Intermec
Intermec PM4I Manuale utente
Intermec
Intermec EasyCoder 601XP Manuale utente
Intermec
Intermec 3400 Manuale utente
Intermec
Intermec EasyCoder 601XP Manuale utente
Intermec
Intermec 074788 Series Manuale utente
Intermec
Intermec EasyCoder PF2i Manuale utente
Intermec
Intermec 825-192-001 Manuale utente
Intermec
Intermec PM4I Manuale utente
Intermec
Intermec ESim v4.20 Manuale utente
Intermec
Intermec EasyCoder 501 SA Manuale utente
