IntesisBox BACnet/IP Server-LON Manuale utente
IntesisBox
®
BACnet/IP Server - LON
Doc. Rev.
1
Installation Manual
URL
email
tel
http://www.intesis.com
+34 938047134
1 / 5
This information is subject to change without notice.
•
IntesisBox must be installed by accredited electrician or similar technical personnel, following all the safety instructions
given here, and in accordance always with the country legislation for installation of electric equipment.
•IntesisBox can not be installed outdoors or exposed to direct solar radiation, water, high relative humidity or dust.
•IntesisBox must only be installed in a restricted access location
•In case of wall mount, fix firmly IntesisBox on a not vibrating surface following the instructions below.
•In case of DIN rail mount fix IntesisBox properly to the DIN rail following the instructions below.
•Mounting on DIN rail inside a metallic cabinet properly connected to earth is recommended.
•Disconnect always power of any wires before manipulating and connecting them to IntesisBox.
•A power supply with an NEC Class 2 or Limited Power Source (LPS) and SELV rated is to be used.
•Respect always the expected polarity of power and communication cables when connecting them to IntesisBox.
•Supply always a correct voltage to power IntesisBox, see details of voltage range admitted by the device in the technical
characteristics below.
•This device was designed for installation in an enclosure. To avoid electrostatic discharge to the unit in environments with
static levels above 4 kV precautions should be taken when the device is mounted outside an enclosure. When working in
an enclosure (ex. making adjustments, setting switches etc.) typical anti-static precautions should be observed before
touching the unit
Safety Instructions
WARNING
Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your
health and also may damage seriously the IntesisBox and/or any other equipment connected to it.
Use the software LinkBoxBacnet to configure IntesisBox, follow the instructions of the user's manual for more
details.
See instructions to download and install the latest version of LinkBoxBacnet
and the user's manual at
http://www.intesis.com/down/bacnet/linkboxbacnet.html
Confi uration and setup
•Disconnect from mains the power supply before connecting it to IntesisBox.
•Disconnect power of any bus or communication cable before connecting it to IntesisBox.
•Mount IntesisBox on the wall or DIN rail following the instruction given below, respecting the safety
instructions given above.
•Connect a NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply to IntesisBox,
respect the polarity if DC power or Line and Neutral if AC power. Apply always a voltage within the range
admitted by IntesisBox and of enough power (see technical characteristics).
•Circuit-breaker must be used before the power supply. Rating 250V-6A
•Connect the communication cables to IntesisBox, see details on the user's manual.
•Power IntesisBox and the rest of devices connected to it.
Installation instructions
IntesisBox
®
BACnet/IP Server - LON
Doc. Rev.
1
Installation Manual
URL
email
tel
http://www.intesis.com
+34 938047134
2 / 5
This information is subject to change without notice.
1. Separate the fixing clips in the bottom of the box, pushing them to the outside until hear the "click" which
indicates that now the clips are in position for wall mount, see in the figure below.
2. Use the holes of the clips to fix the box in the wall using screws. Use the template below for the wall holes.
With the clips of the box in their original position, insert first the box in the upper edge of the DIN rail and later insert
the box in the down part of the rail, using a small screwdriver and following the steps in the figure below.
Wall mount
Clips in their original position, for DIN rail
mount Clips in position for wall mount
DIN
Rail
1
2
3
Top view of the box
DIN rail mount
Side view of the box
Botton view of the box
100 mm
IntesisBox
®
www.intesis.com
61 mm Ø 3 mm
IntesisBox
®
BACnet/IP Server - LON
Doc. Rev.
1
Installation Manual
URL
email
tel
http://www.intesis.com
+34 938047134
3 / 5
This information is subject to change without notice.
Connections
________________________________________________________________________________________
Notes:
1. Must use NEC Class 2 or Limited Power Source (LPS) and SELV rated power supply.
If using DC power supply:
•Respect polarity applied of terminals (+) and (-). Be sure the voltage applied is within the range admitted
(9 to 30 Vdc). The power supply can be connected to earth but only through the negative terminal, never
through the positive terminal.
If using AC power supply:
•
Make sure the voltage applied is of the value admitted (24 Vac). Do not connect any of the terminals of the
AC power supply to earth, and make sure the same power supply is not supplying any other device.
2. BACnet/IP connection: Connect the cable coming from the BACnet/IP client to the connector ETH of IntesisBox, use
a crossover or a straight ethernet CAT5 cable connecting to a hub or switch of the LAN of the building. Contact the
network administrator and make sure that UDP traffic and the port used (47808 by default) are allowed through all
the LAN path.
3. Use the software LinkBoxBacnet to configure IntesisBox. See the user's manual for details.
Console wire 1.8 m long.
DB9 Female - DB9 Male
standard. It is supplied.
LinkBoxBacnet
Only needed for
configuration
See Note 3
Power
See Note 1
BACnet/IP
See Note 2
LON
TP/FT-10
PC Console
- + Ethernet
BACnet/IP
IntesisBox
®
www.intesis.com
Ethernet
RJ45
B A
LON TP/FT-10
CMN 24Vac
9 - 30Vdc
Max.125 mA
24Vac
Max.127mA
50-60H
IntesisBox
®
BACnet/IP Server - LON
Doc. Rev.
1
Installation Manual
URL
email
tel
http://www.intesis.com
+34 938047134
4 / 5
This information is subject to change without notice.
Enclosure Plastic, type PC (UL 94 V-0).
Dimensions: 107mm x 105mm x 58mm.
Colour Light Grey. RAL 7035.
Power
9 to 30Vdc +/-10%, Max.: 125mA.
24Vac +/-10% 50-60H , Max.: 127mA
Must use a NEC Class 2 or Limited Power Source (LPS) and SELV
rated power supply.
Plug-in terminal block for power connection (2 poles).
Terminal wiring (for
power supply and
low-voltage signals)
Per terminal: solid wires or stranded wires (twisted or with ferrule)
1 core: 0.5mm
2
… 2.5mm
2
2 cores: 0.5mm
2
… 1.5mm
2
3 cores: not permitted
Mounting options Wall.
DIN rail EN60715 TH35.
BACnet/IP port 1 x Ethernet 10Base-T (RJ45).
LON port 1 x LON (TP-FT/10) (plug-in terminal block 2 poles). TNV-1
LED indicators
1 x Power.
2 x LON port activity (Tx, Rx).
2 x Ethernet port link and activity (LNK, ACT).
1 x LON service.
1
Push buttons 1 x LON service.
1
Console port EIA232. DB9 female connector (DCE). SELV
Configuration Via console port.
2
Firmware Allows upgrades via console port.
Operational
temperature 0°C to +70°C
Operational
humidity 25-90% at 50ºC, non condensing
Protection IP20 (IEC60529).
RoHS conformity Compliant with RoHS directive (2002/95/CE).
Norms and
standards
CE conformity to EMC directive (2004/108/EC) and Low-voltage
directive (2006/95/EC)
EN 61000-6-2
EN 61000-6-3
EN 60950-1
EN 50491-3
1
Not used for the moment. Reserved for future use.
2
Standard cable DB9male-DB9female 1,8 meters long is supplied with the device for connection to a PC COM port for
configuring and monitoring the device. The configuration software, compatible with Windows
®
operating systems, is also supplied.
Technical characteristics
IntesisBox
®
BACnet/IP Server - LON
Doc. Rev.
1
Installation Manual
URL
email
tel
http://www.intesis.com
+34 938047134
5 / 5
This information is subject to change without notice.
Dimensions
External dimensions.
Free space recommended to install the device, with spacing enough for external connections.
115 mm
130 mm
100 mm
Power
+
Ethernet port
107 mm
105 mm
58 mm
Console
port
LON port
Indice
Altri manuali IntesisBox Server
IntesisBox
IntesisBox IBOX-ASCII-KNX Manuale utente
IntesisBox
IntesisBox BACnet/IP Server–Modbus TCP master Manuale utente
IntesisBox
IntesisBox Modbus TCP Server-Modbus RTU Master Manuale utente
IntesisBox
IntesisBox Modbus Server-Galaxy EIA232 Manuale utente
IntesisBox
IntesisBox KNX TP-1 (EIB) Manuale utente
IntesisBox
IntesisBox ASCII Server-KNX Manuale utente
IntesisBox
IntesisBox BACnet/IP Server-Notifier ID3000 Manuale utente
IntesisBox
IntesisBox IBOX-MBS-KNX-100 Manuale utente
IntesisBox
IntesisBox MH-RC-BAC-1 Manuale utente
IntesisBox
IntesisBox IBOX-ASCII-BAC-A Manuale utente
IntesisBox
IntesisBox BACnet/IP Server-Modbus RTU master Manuale utente
IntesisBox
IntesisBox Modbus Server-Algorinet Manuale utente
IntesisBox
IntesisBox Modbus Server-Cerberus ISO1745 Manuale utente
IntesisBox
IntesisBox IBMBSKNX1000000 Manuale utente
IntesisBox
IntesisBox BACnet/IP Server-FIDELIO TCP/IP Manuale utente
IntesisBox
IntesisBox Modbus Server-AlgoRex Manuale utente
IntesisBox
IntesisBox Modbus Server-Mitsubishi Heavy Industries AC Manuale utente
IntesisBox
IntesisBox BACnet/IP Server-SUNWAYS Manuale utente
IntesisBox
IntesisBox IBOX-ASCII-KNX Manuale utente
IntesisBox
IntesisBox BACnet/IP Server-DALI Manuale utente
