Janitza FBM Series Manuale utente

Dok Nr. 2.204.002.4 - Vers. 1.2 Art. Nr. 33.03.154

www.janitza.com

Janitza electronics GmbH

Vor dem Polstück 1

D-35633 Lahnau

Support Tel. 0049 6441 9642-22

Fax 0049 6441 9642-30

E-mail: [email protected]

Internet: http://www.janitza.com

FBM series

I/O modules

Functional description

UMG604 - UMG605 - UMG508 - UMG511

Item no.: 15.06.075 / 15.06.076 / 15.06.077

15.06.078 / 15.06.079

FBM-Serie

Content

General 3

local I/O modules of the FBM10 series 6

General 6

Establishing communication to the measurement device 7

Setting the IP address of the computer 9

Connection to the RS485 10

DIP switch 10

Bus address (DIP switches 1 to 6) 11

Parity 11

Baud rate (DIP switches 9 and 10) 11

Connection diagram FBM10R 12

Connection diagram FBM10I 12

Connection diagram FBM10PT1000/PT100 13

Connection diagram FBM DI8AI8 13

LED display 14

Example control of the FBM10R module with JASIC 18

Temperature measurement APP for module FBM10PT1000 20

JASIC programs for module DI8AI8 22

Control with modbus diagnostics tool for module DI8AI8 24

Storing the analogue input measurement values from module FBM-DI8AI8 26

Technical data 28

FBM-Serie

General

This operating manual is subject to the legal requirements for copyright protection and may not

be, either in whole or in part, photocopied, reprinted, or reproduced by mechanical or electronic

means, or in any other manner be duplicated or redistributed without the legally binding, written

agreement of

Janitza electronics GmbH, Vor dem Polstück 1,

D 35633 Lahnau, Germany.

Trademarks

All trademarks and their resulting rights belong to the respective holders of these rights.

Disclaimer

Janitza electronics GmbH takes no responsibility for errors or defects within this operating manual

and takes no responsibility for keeping the contents of this operating manual up to date.

Comments on the operating manual

We welcome your comments. In the event that anything in this operating manual seems unclear,

please let us know and send us an EMAIL at: [email protected].

FBM-Serie

cDangerous voltage!

Danger to life or risk of serious injury.

Disconnect system and device from power

supply before beginning work.

mAttention!

Please follow the documentation. This

symbol warns of possible dangers that can

arise during installation, commissioning

and use.

CNote!

Meaning of the symbols

The following pictograms are used in the operating manual at hand:

FBM-Serie

Instructions for use

Please read the operating manual at hand as well as all other publications that must be drawn from

for working with this product (in particular for the installation, operation or maintenance).

Follow all safety regulations and warning information. If you do not follow the information, it can

result in bodily injury and/or damage to the product.

Any unauthorized changes or use of this device, which transcend the mechanical, electrical or

otherwise stated operating limitations, can result in bodily injury or/and damage to the product.

Any of such unauthorized changes constitute „misuse“ and/or „negligence“ in terms of the war-

ranty for the product and therefore eliminates the warranty for covering any potential damages

resulting from this.

This device is to be operated and maintained exclusively by specialized personnel.

Specialized personnel are persons, that based on their respective training and experience, are

qualiﬁed to recognize risks and prevent potential dangers that can be caused by the operation or

maintenance of the device.

Additional legal and safety regulations required for the respective application are to be following

during the use of the device.

cIf the device is not operated according

to the operating manual, protection is no

longer ensured and danger can come from

the device.

cDangerous voltage!

Disconnect system and device from power

supply before beginning work.

FBM-Serie

local I/O modules of the

FBM10 series

General

With the local I/O modules of the FBM se-

ries, the inputs and outputs of device types

UMG604 / UMG605 / UMG508 and UMG511

can be expanded inexpensively. The ﬁeldbus

module has no intelligence, rather it simply

directs the various input and output signals

together in order to distribute them to the re-

spective subscribers

The devices of the UMG104 and UMG507 se-

ries are not useable as masters for the FBM

modules. There are four I/O modules available:

• The ﬁeldbus module FBM 10R

(item no.: 15.06.075) has

10 relay outputs

• The FBM 10I module

(item no.: 15.06.076) has 10 digital

inputs.

• The ﬁeldbus module FBM P10PT1000

(item no.: 15.06.077) has 10 temperature

inputs.

• The module FBM DI8-AI8

(item no.: 15.06.079) has 8 digital and

8 analog inputs

The I/O modules of the FBM series are con-

nected to the RS485 interface of the power

analyzer. The analyzer works in Modbus Mas-

ter Mode in doing so. The maximum stitch

length (cable length) between the master and

the module may not exceed 1000m.

Up to 12 I/O modules in total (6x 10 outputs

/ 6x 10 inputs) can be controlled via the „Ja-

sic“ graphic programming in conjunction with

the Emax App. However, with the standard

PT1000/PT100 APP (temperature module)

and with the standard AI8-DI8 APP (ﬁeldbus

module) only one module can be controlled.

The I/O‘s (channels) are permanently assigned

and are automatically addressed to the Emax

program.

FBM-Serie

Establishing communication to the measurement device

In order to set the Emax parameters, the ﬁrst step is establishing the communication between the

measurement device and a computer. We recommend installing the conﬁguration and evaluation

software „GridVis“. The measurement device should be assigned an IP address, the entry of the

IP address is different for display devices and mounting rail devices. The IP address helps identify

the measurement device in an ethernet network.

Setting the IP address on a UMG604 / UMG605

1. Simultaneously press key 1 and key 2 one second

2. You are now in the parameter menu.

The letters PRG identify this menu.

CNote!

Key 1: Change segment selection

Key 2: Change value (long - / short +)

The following parameters must be parameterized for the Emax function on the device:

Parameter Designation Parameter

recommendation

Settings

205 TCP mode 0 Fixed IP

203 RS485 mode 1 Master

202 RS485 baud rate 2 38,4 kbit/s

200 Device ID >33 >32

300 IP Adresse XXX --- --- --- 192 *

301 IP address --- XXX --- --- 168 *

302 IP address --- --- XXX --- 001 *

303 IP address ---.--- --- XXX 010 *

304 IP mask XXX --- --- --- 255 *

305 IP mask --- XXX --- --- 255 *

306 IP mask --- --- XXX --- 255 *

307 IP address ---.--- --- XXX 000 *

*Parameters can be freely selected or parameterized according to recommendations

FBM-Serie

Setting the IP address on a UMG508 / UMG511

1. Press the „ESC“ key in order to access the

conﬁguration menu

2. Go into the communication menu

3. Set the parameters from the following list

(recommendation):

Proposal:

DHCP Off

Address 192.168.1.10

Net mask 255.255.255.0

Gateway --

Protocol Modbus Gateway

Address >33

Baud rate 38400

FBM-Serie

Setting the IP address of the computer

The following setting example was made in Windows XP, the example shows a point-to-point con-

nection with an ethernet cable (cross patch). Settings in a company network can vary!

The IP settings are shown here with the Windows XP operating system as an example. It should

be noted here that for a point to point connection, the ﬁrst three segments of the IP should be

the same. The Subnet mask should be exactly the same for the PC and the measurement device.

Give your computer the IP 192.168.1.1 (recommendation) and the subnet mask 255.255.255.0.

Conﬁrm with OK.

FBM-Serie

Connection to the RS485

The ﬁeldbus modules are connected in

a bus structure (in a line). A terminating

resistor (120Ohm 1/4W) is to be set at

the end of the bus line.

CNote!

A Proﬁbus cable or a cable of the

type Li2YCY(TP) 2x2x0.22 are be

used as the cable type. The cable

must be shielded and drilled!

Example connection UMG604/605:

UMG604 terminal 23 (A)  FBM 10R / FBM 10I / FBM 10PT1000 / FBM DI8-AI8 on terminal (A)

UMG604 terminal 22 (B)  FBM 10R / FBM 10I / FBM 10PT1000 / FBM DI8-AI8 on terminal (B)

Correct Incorrect

DIP switch

For serial communication, several default settings must be implemented. These settings are car-

ried out on the ﬁeldbus device using the ten available DIP switches.

The DIP switches have the following functions ON

1 Address 6 P E Bd

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali janitza Strumento di misura

janitza

janitza UMG 96-PA Manuale utente

janitza

janitza UMG 801 Manuale di istruzioni

janitza

janitza UMG 509 Manuale di istruzioni

janitza

janitza UMG 804 Manuale di istruzioni

janitza

janitza UMG 604 Manuale utente

janitza

janitza UMG 801 Manuale utente

janitza

janitza 800-CT8-A Manuale utente

janitza

janitza UMG 96-PA Manuale utente

janitza

janitza UMG 96-PQ-L Manuale di istruzioni

janitza

janitza UMG 96-PA Manuale utente

janitza

janitza optec UMG-96 Manuale utente

janitza

janitza UMG 512 PRO Manuale utente

janitza

janitza UMG 96 RM-M Manuale di istruzioni

janitza

janitza UMG 96-PA Manuale utente

janitza

janitza UMG 806 Manuale di istruzioni

janitza

janitza UMG96L Manuale utente

janitza

janitza UMG 604 Manuale utente

janitza

janitza UMG 96-S2 Manuale utente

janitza

janitza UMG 96-S2 Manuale di istruzioni

janitza

janitza UMG 605 Manuale utente

janitza

janitza UMG 103-CBM Manuale utente

janitza

janitza UMG507 Istruzioni per l'uso e l'installazione

janitza

janitza UMG 503 Manuale utente

janitza

janitza UMG 96-PA Manuale di istruzioni

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente

janitza FBM Series Manuale utente

Manuali Strumento di misura popolari di altre marche