JNE TECH-D Manuale utente
Instruction Manual
ENGLISH
___________________________________________________________________________
______________________________________________________________________________
2
TECH-D manual EN 2010-05-18.doc
Instruction Manual
INDEX 1 Introduction
1.1 General.…………………..…......…………. 3
1.2 Maintenance.…………...............………… 4
1.3 Warranty………………………….………… 5
2 TECH-D measuring tool
2.1 General description…...…………………... 6
2.2 Display function…..……………………….. 7-10
2.3 Height level rods..………………………… 11
2.4 Magnetic attachment……………………… 11
2.5 Height measuring rods……………………. 11
2.6 Level………………………………………... 11
2.7 Measuring sockets……………….……….. 12
2.8 Short measures……………………………. 12
2.9 Change out batteries……………………… 13
2.10 Technical specification….……….……….. 14
4 Measuring
4.1 Mounting the magnetic attachment 31
4.2 Choose magnet attachment……………… 32
4.3 Length measuring…………………………. 33
4.4 Symmetry measuring…………………….. 34-35
4.5 Comparing heights……………………….. 36
4.6 Position of the vehicle……………………. 37
5 Measuring without data sheet
5.1 Quick guide…………………..……………. 38
6 Adaptors
6.1 Adaptors……………………………………. 39
7 Technical notes
7.1 Spare parts………………………………… 40
7.2 Declaration of conformity…………………. 41
___________________________________________________________________________
______________________________________________________________________________
3
TECH-D manual EN 2010-05-18.doc
1 INTRODUCTION
1.1 General Congratulations on your purchase of the
TECH-D vehicle measurement tool.
TECH-D is an digital measurement tool intended
for measuring and checking dimensional
accuracy of vehicle unibody and frame.
The tool consists the following main
components:
•TECH-D measuring tool
•chassis attachments
•datum rods
•height measuring rods
•measuring sockets and tips
•metal plate
•Web based software access where you
type in measuring values from the tool
and produce reports.
See separate software manual
The measuring arm and its attachments and
measuring tips, together with web based
software, makes it possible to measure lengths
in 2 dimensions. You can also compare the
symmetry in height between left and right
side in a very time effective way.
These instructions contain a description of the
equipment and directions for its use, handling
and maintenance.
IMPORTANT!
Read the instructions carefully in order to fully
understand the correct handling of the TECH-D
measurement.
The equipment is intended for use in the auto
body shop environment and in accordance with
all recognized official safety procedures.
Photos and drawings used throughout these
instructions depict the fundamental features and
design of the product at the time of publishing
and do not reflect potential future design
changes.
___________________________________________________________________________
______________________________________________________________________________
4
TECH-D manual EN 2010-05-18.doc
WARNING!
Do not store or keep TECH-D near
computers, credit cards or other magnetic
sensible things, though the magnet in the
chassis attachment may damage these.
1.2 Maintenance A. General
The TECH-D measuring tool includes an digital
measuring arm, a precision instrument requiring
proper care and maintenance to maintain its
accuracy and performance.
Please follow all instructions and safety
procedures very carefully to maintain equipment
reliability and to benefit from all of its great
features.
B. Maintenance
Be sure to clean all equipment after every use.
Special care should be taken when cleaning the
digital measuring arm, in particular each of the
moving surfaces.
Use a clean dry cloth without detergent.
Return all parts to the storage box after every
use. Check each part individually for any
damage that may have occurred during use.
C. Inspection
Have your distributor inspect the complete
system at least once every year or when you
suspect damaged has occurred, to ensure
accuracy and reliability.
TECH-D certified distributors use control
instruments provided by JNE AB to accurately
perform inspections.
D. Scrapping
When it becomes necessary to scrap any of the
TECH-D measuring tool equipment or parts it is
essential that every item be sorted for recycling
in accordance with local, state and federal
requirements.
___________________________________________________________________________
______________________________________________________________________________
5
TECH-D manual EN 2010-05-18.doc
1.3 Warranty IMPORTANT NOTICE!
AVOID PERSONAL INJURY OR DAMAGE TO
EQUIPMENT!
Read all instructions to assure the correct use of
the TECH-D measurement tool. Incorrect
handling can result in personal injury or damage
to the equipment.
A one-year warranty is applicable from the date
of delivery, and refers to defects in materials
and assumes normal care and maintenance.
The warranty assumes that:
•TECH-D equipment has been used and
maintained in accordance with the instructions
outlined in this manual.
•Equipment has not been modified or rebuilt
without the prior approval of JNE AB via its
authorized distributor network.
•Only genuine TECH-D parts have been used in
repairs.
Photos and drawings used throughout these
instructions depict the fundamental features and
design of the product at the time of publishing
and do not reflect potential future design
changes.
TECH-D equipment is intended for use in the
auto body shop environment and in accordance
with all recognized and applicable safety rules
and regulations.
All claims must be referred to an authorized
TECH-D distributor for evaluation.
___________________________________________________________________________
______________________________________________________________________________
6
TECH-D manual EN 2010-05-18.doc
2 TECH-D MEASURING TOOL
2.1 General description
TECH-D MEASURING TOOL
A lightweight telescoping digital measuring arm
made up of aluminum and composite materials
forms the main component of the tool.
In the rear end of the tool is an attachment for
height level rods. A quick release built accepts
the height level rods. On the ball of the rod,
snap on the magnetic attachment.
The housing of the digital control unit with digital
display located on the front end of the arm
incorporates an easy to operate twist-lock
socket for each of the 3 different lengths of
height measuring rods.
A level assembly is built into the top of the
housing of the digital unit, for identification of the
vehicle’s height divergences on symmetric
points, left and right side of the vehicle.
Measurement control buttons are located in the
front face of the digital unit. You can here
choose your way of measuring by pressing the
control buttons.
Inside the front face are most of the digital parts.
Also a battery compartment for the two AA
batteries with a consumption time of minimum
50 hours continuously use.
For operating instructions – refer to item
numbers 2.2-2.10
___________________________________________________________________________
______________________________________________________________________________
7
TECH-D manual EN 2010-05-18.doc
2.2 Display function
START UP TECH-D
NOTE! When you start make sure the
telescoping measuring arm is completely
collapsed.
Start the digital by pressing the button
briefly. A digital number 900 (900mm) will
appear in the display window representing the
minimum collapsed length between the height
calibration rod and datum height rod centres.
Note: If display does not read 900 - switch
off by holding down the On/0 button for a
few seconds and restart following the above
procedure.
NORMAL MEASURING
This is the automatic setting after start.
The measuring tool work in the area of
900-2650 mm.
SHORT MEASURES
To measure short measures, 400-2150 mm,
press for 2 seconds.
Use the tip holder that is attached underneath
the measuring arm. Use this measuring area
preferably under hood.
COMPARATIVE MEASURING
The digital reading can be reset for quick
comparative checks during normal length
measuring operations by briefly pushing the
button to select 0 mm. From this point any
change in length will register plus or minus in 1
mm gradients. Additional comparative checking
is possible by repeating the above procedure at
any time during comparative checking.
___________________________________________________________________________
______________________________________________________________________________
8
TECH-D manual EN 2010-05-18.doc
HOLD
FREEZE A MEASURING VALUE
Push this button to freeze a measured value in
the display. Push it a second time to release this
feature.
DISPLAY BRIGHTNESS
Hold this button to increase display brightness –
release button when the required setting has
been obtained.
ENERGY SAVING FUNCTION
The display will automatically shut down after 5
minutes and be energised again at the slightest
movement of the measuring arm.
SHUT OFF FUNCTION
The display will shut down all circuits after 90
minutes of non operation.
The measuring arm can also be switched off
manually by depressing the button
for >3 seconds.
___________________________________________________________________________
______________________________________________________________________________
9
TECH-D manual EN 2010-05-18.doc
Display functions
ON
900-2650
400-2150
OFF
Press >2 sek
Press <1
Comparative
measuring (+ and -)
Press > 3 sek
___________________________________________________________________________
______________________________________________________________________________
10
TECH-D manual EN 2010-05-18.doc
Program menu measuring
ON
900
400
OFF
< 1 sek Comparative
measuring
> 2 sek
> 2 sek
Indice
Altri manuali JNE Strumento di misura
