Johnson Controls Mercury 3 Series Manuale

24-10707-198 Revision –

December 2017

P2000

Security Management System

CKM-MR52-S3

authentic Mercury™ terminal module

hardware

installation

Johnson Controls

No part of this document may be reproduced without the prior permission of Johnson Controls.

If this document is translated from the original English version by Johnson Controls, all reasonable

endeavors will be used to ensure the accuracy of translation. Johnson Controls shall not be liable

for any translation errors contained herein or for incidental or consequential damages in connection

with the furnishing or use of this translated material.

Due to continuous development of our products, the information in this document is subject to

change without notice. Johnson Controls shall not be liable for errors contained herein or for

incidental or consequential damages in connection with furnishing or use of this material. Contents

of this publication may be preliminary and/or may be changed at any time without any obligation to

notify anyone of such revision or change, and shall not be regarded as a warranty.

Other Manufacturers’ Documentation

Johnson Controls does not duplicate documentation of other equipment manufacturers. When

necessary, Johnson Controls provides documentation that supplements that of other manufacturers.

When unpacking your equipment, keep all original manufacturer documentation for reference.

Technical Support

For factory technical support, Johnson Controls authorized field technicians or authorized dealer

representatives can contact Global Security Solutions Technical Support by phone at

(866) 893-0423 or (414) 524-1214, or by email at [email protected]. They

can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.

End users and customers should contact their local Johnson Controls branch or authorized dealer

for any of their support needs (technical support, maintenance contracts, on-site field support,

P2000 Software Service Agreements, Service Partnerships, and so on). Visit

http://www.johnsoncontrols.com/location-finder to find your local Johnson Controls office.

For material returns contact the branch if the material was purchased through a Johnson Controls

branch or through the Product Sales Operations Team, if ordered through the Advanced Order

Management System (AOMS) and follow the RMA process; or contact the authorized dealer

representative where the material was purchased directly.

Single Point of Contact by Region

Acknowledgment

Metasys® and Johnson Controls® are trademarks of Johnson Controls. All other company and

product names are trademarks or registered trademarks of their respective owners.

European Single Point of Contact

JOHNSON CONTROLS

WESTENDHOF 3

45143 ESSEN

GERMANY

NA/SA Single Point of Contact

JOHNSON CONTROLS

507 E MICHIGAN ST

MILWAUKEE WI 53202

USA

APAC Single Point of Contact

JOHNSON CONTROLS

C/O CONTROLS PRODUCT

MANAGEMENT

NO. 22 BLOCK D NEW DISTRICT

WUXI JIANGSU PROVINCE 214142

CHINA

Declarations of Conformity

United States: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Canada: CAN ICES-3 (A)/NMB-3(A)

European Union: This product complies with the requirements of the EMC Directive.

This equipment must not be modified for any reason and it must be installed as stated in the

Manufacturer’s instruction.

If this shipment (or any part thereof) is supplied as second-hand equipment, equipment for sale

outside the European Economic Area or as spare parts for either a single unit or system, it is not

covered by the Directives.

UNDERWRITERS LABORATORIES COMPLIANCE VERIFICATION SHEET

The following model number is listed under Underwriters Laboratories® (UL) 1076 for Proprietary

Burglar Alarm Units and Systems, UL 294 for Access Control Systems Units and Underwriters

Laboratories of Canada ULC/ORD-C1076-86.

CKM-MR52-S3

When installed at the site the following requirements must be met to comply with these standards.

1. The CKM-MR52-S3 shall be mounted in Listed Enclosures CKM-CE75-E2M, CKM-CE150-

E4M, and Listed Burglar Alarm and Access Control System Units SPF10000-1I00, SPF1I100-

1I00 or SPF1I300-1J00.

2. A CKM-MR52-S3 mounted in Listed Enclosures CKM-CE75-E2M, CKM-CE150-E4M, and

Listed Burglar Alarm and Access Control System Units SPF10000-1I00, SPF1I100-1I00 or

SPF1I300- 1J00 shall be powered through the CKM-F8P power distribution module.

3. Transient protection devices that are installed must not be removed or defeated.

4. Do not connect equipment to an AC power source that is controlled by a switch.

5. A 1.5Kohm/750ohm custom end-of-line resistance supervised circuit was investigated by

Underwriter Laboratories.

6. Power for devices connected through relay/control output wiring must be provided by a UL

Listed power limited power source.

7. RS485-type readers have not been investigated by Underwriters Laboratories.

8. Encrypted communication has not investigated by Underwriters Laboratories.

9. For a UL 294 Listed system the following Listed readers may be used.

Manufacturer Models

HID Global Corp. 30387, 31503, 31815, 31880, 32005, 32788, 32985

5355, 5365, 5395, 5405, 5455, 6005, 6100, 3110-6445,

R10T, R10N, R15N, R15T, RP15N, RP15T, R40N,

R40T, RK40N, RK40T, RP40N, RP40T, RPK40N,

RPK40T

All models may be followed by additional suffixes

OSDP Readers: R10Exxx, RP10Exxx, R15Exxx, RP15Exxx,

R30Exxx, RP30Exxx, R40Exxx, RP40Exxx, RK40Exxx,

RPK40Exxx.

All models may be followed by additional suffixes. The last “X” in

the model number maybe an “R” or “N”

Mercury Security Corp. MR-5, MR-20

10. The maximum Wiegand line impedance is 8 ohms, representing 22 AWG @ 500 feet.

11. The HID 3110-6445 shall be powered by a separate power source that is UL 294 or UL 603

power limited power source.

12. Suitable for use with the model P2K-nnn-UL-x Security Management System, where n can be

any number 0 through 9 and where x can be any three letters A through Z.

13. UL 294 Performance Levels

Destructive Attack Level I

Endurance Level IV

Line Security Level I

Standby Power Level I

CKM-MR52-S3 Hardware Installation Manual

24-10707-198 Rev. –

CKM-MR52-S3 READER TERMINAL MODULE

This document provides hardware installation and setup instructions for

CKM-MR52-S3, the authentic Mercury™ dual reader terminal module

Series 3. This document is divided into the following sections:

•General Information on page 1

•Mounting Information on page 2

•Wiring Information on page 2

•Jumper and DIP Switch Usage on page 7

•Status LEDs on page 9

•Specifications on page 11

•Maintenance on page 12

NOTE: Throughout this manual the CKM-MR52-S3 module is also referred to as

the CKM-MR52.

GENERAL INFORMATION

The CKM-MR52 reader interface provides a solution to the OEM system

integrator for interfacing to TTL, Wiegand, or RS-485 type readers and door

hardware. The CKM-MR52 can accept data from reader with clock/data,

Wiegand, or RS-485 signaling, and provide a tri-stated LED control and buzzer

control. Six form-C relay outputs may be used for strike control or alarm

signaling. Eight supervised inputs are provided for monitoring the door contact,

exit push button, and alarm contacts. Communication to the CKM-MR52 is

accomplished via a 2-wire RS-485 interface.

The CKM-MR52 requires 12 to 24 VDC for power. See the following figure

for component location.

CKM-MR52-S3 Hardware Installation Manual

24-10707-198 Rev. –

MOUNTING INFORMATION

Figure 1: CKM-MR52 Hardware

WIRING INFORMATION

This sections covers the following:

•Cable Routing

•Power Wiring

•Communications Wiring (SIO Communication Port)

•Reader Wiring

•Alarm Contact Wiring

•Control Output Wiring

CKM-MR52-S3 Hardware Installation Manual

24-10707-198 Rev. –

Cable Routing

The cables should run in grounded conduit or at least two feet from AC

power, fluorescent lights, or other high energy sources.

IMPORTANT: All data cables should be physically separated from power lines. If

conduit is used, do not run data cables in the same conduit as power cables or

certain door strike cables, e.g. strike voltage greater that 42V or Magnetic door

locks without EMI suppression.

All cables must conform with the following regulations:

• National Electrical Code

•NFPA 70

• Local electrical codes

• Canadian Electric Code C22.1 (installations in Canada)

• BSI Standard BS7671, latest edition (installations in Great Britain)

Cabling should be made using good wiring practices and should be long

enough to allow service loops at their terminations in the enclosure.

Power Wiring

The CKM-MR52 accepts 12 to 24 VDC for power on TB7. Locate the

power source as close to the CKM-MR52 as possible. Make power

connection with minimum of 18 AWG wires.

Figure 2: CKM-MR52 Supplying Power

IMPORTANT: Observe polarity on VIN.

NOTE: VOUT is not used.

12 TO 24Vdc

GND

VIN

TB7

CKM-MR52-S3 Hardware Installation Manual

24-10707-198 Rev. –

Communications Wiring (SIO Communication Port)

The CKM-MR52 communicates to an intelligent controller (for example,

CKM-EP2500) via a 2-wire RS-485 interface. The CKM-MR52 allows

for multidrop communication on a bus of up to 4,000 feet (1,200 m). Use

twisted pairs (minimum 24 AWG) with drain wire and shield for

communication. See Specifications for details.

Install RS-485 termination jumper, J4, on the interface boards at each end

of the communication line only.

Figure 3 shows the CKM-MR52 communications wiring.

Figure 3: CKM-MR52 Communications Wiring

Reader Wiring

Each reader port supports a reader with TTL (D1/D0, Clock/Data) or 2-wire

RS-485 signaling. Power to the reader is selectable: 12 VDC (VIN must be

greater than 20 VDC), or power is passed-through (PT) from the input voltage

of the MR52 (TB7-VIN), 300 mA maximum per reader port. Readers that

require different voltage or have high current requirements must be powered

separately. Refer to the reader manufacture specifications for cabling

requirements. In the 2-wire LED mode the buzzer output is used to drive the

second LED. Reader port configuration is set via the host software.

CKM-MR52-S3 Hardware Installation Manual

24-10707-198 Rev. –

To fully utilize each reader port:

• TTL signaling requires a 6-conductor cable (18 AWG)

• RS-485 signaling requires two 2-conductor cables. Use one cable for

power (18 AWG) and one cable for communication (24 AWG, with

drain wire and shield).

Figure 4: J1 - Reader Port Power Select

Figure 5: Typical D1/D0 - Clock/Data Reader

Figure 6: Typical 2-Wire RS-485 Device

NOTE: If the input voltage to the MR52 is 12 VDC, jumper J1 must be in the PT

position.

CKM-MR52-S3 Hardware Installation Manual

24-10707-198 Rev. –

Alarm Contact Wiring

There are 8 inputs that are typically used to monitor door position,

request to exit or alarm contacts. Input circuits can be configured as:

• Unsupervised alarm (2 states); reporting as open or closed contact.

• Supervised alarm (6 states); reporting as open or closed contact, open

circuit, shorted circuit, grounded circuit *, or foreign voltage*.

A supervised input circuit requires adding two resistors with value of 1k

Ohm, 1% to the circuit to facilitate proper reporting and should be located

as close to the sensor as possible. Custom end of line (EOL) resistances

may be configured via the host software.

* Grounded and foreign voltage states are not a requirement of UL 294

and therefore not verified by UL.

The input circuit wiring configurations shown are supported but may not

be typical.

Figure 7: CKM-MR52 Alarm Contact Wiring

There are two additional inputs for monitoring cabinet tamper (TMP) and

power failure (PFL). These two inputs do not use EOL resistors and are

for contacting monitoring only.

Control Output Wiring

Six form-C contact relays are provided for controlling door strikes or

other devices. Load switching can cause abnormal contact wear and

premature contact failure. Switching of inductive loads (strike) also

causes EMI (electromagnetic interference) which may interfere with

normal operation of other equipment.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Johnson Controls Unità di controllo

Johnson Controls

Johnson Controls M300CJ-R Manuale utente

Johnson Controls

Johnson Controls tyco AMD-1 Manuale utente

Johnson Controls

Johnson Controls METASYS NU-XBN101-0 Manuale utente

Johnson Controls

Johnson Controls Tyco 8200-1466-01 Manuale utente

Johnson Controls

Johnson Controls PENN P470 Manuale

Johnson Controls

Johnson Controls tyco AMD-2 Manuale utente

Johnson Controls

Johnson Controls GS Series Manuale utente

Johnson Controls

Johnson Controls IOM1711 Manuale utente

Johnson Controls

Johnson Controls S1-TTSCC01 Manuale utente

Johnson Controls

Johnson Controls System 450 Series Manuale utente

Johnson Controls

Johnson Controls GS-20 Series Manuale utente

Johnson Controls

Johnson Controls P352PN-2 Manuale utente

Johnson Controls

Johnson Controls Penn A19K Series Manuale utente

Johnson Controls

Johnson Controls VP140 L Series Manuale utente

Johnson Controls

Johnson Controls C450CCN-2 Manuale utente

Johnson Controls

Johnson Controls Autocall MX Indoor Isolated Callpoint Manuale utente

Johnson Controls

Johnson Controls Tyco HSM3408 Manuale utente

Johnson Controls

Johnson Controls Penn System 350 S350P Manuale utente

Johnson Controls

Johnson Controls Tyco DV-5a Series Manuale utente

Johnson Controls

Johnson Controls System 350 Manuale di servizio

Johnson Controls

Johnson Controls CKM-MR51E Istruzioni per il montaggio

Johnson Controls

Johnson Controls GS-20 Series Manuale utente

Johnson Controls

Johnson Controls IOM3711 Manuale utente

Johnson Controls

Johnson Controls NIE39 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente