JYTEK PXI-93518 Manuale utente
PXI-93518
8 Ports Serial
Communication Modules
User’s Manual
User Manual Version: V1.0.0
Revision Date: Nov 10, 2021
© Copyright 2021 Shanghai Jianyi Technology Co., Ltd
All Rights Reserved.
Manual Revision 1.0: Nov 10, 2021
The information in this document is subject to change without prior notice in order
to improve reliability, design and function and does not represent a commitment on
the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
Trademarks
PXI-93518 are registered trademarks of JYTEK, Windows 7, Windows 10 are
registered trademarke of Microsoft- Corporation. Intel@ is a registered trademark of
Intel Corporation.Other product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their
respective companies.
Table of Contents
1. Introduction............................................................................................................... 1
1.1 PXI-93518 Overview ....................................................................................... 1
1.1.1 What is the PXI-93518........................................................................... 1
1.1.2 PXI-93518 Features............................................................................... 1
1.1.3 PXI-93518 Connector Pin Assignment...................................................3
2. Installation................................................................................................................. 5
2.1 What You Have................................................................................................. 6
2.2 Unpacking.........................................................................................................6
2.3 Installation Procedure...................................................................................... 6
2.4 Hardware Configuration...................................................................................7
2.5 Software Installation........................................................................................ 7
2.5.1 Windows 7 Installation..........................................................................7
Figure 1 RS-422 Functional Structure..................................................................2
Figure 2 RS-485 Functional Structure..................................................................2
Figure 3 RS-232 Functional Structure..................................................................3
Figure 4 Connector DB62.................................................................................... 5
Figure 5 Device Manager.....................................................................................7
Figure 6 Update Driver Software.........................................................................8
Figure 7 Find Driver Software..............................................................................8
Figure 8 Select Driver Software...........................................................................9
Figure 9 Driver Updated Successfully..................................................................9
Figure 10 The board be recognized...................................................................10
Figure 11 The ports be recognized....................................................................10
Table 1 PXI-93518 Connector Pin Assignment....................................................4
Table 2 Notes to Legend in the Pin Definitions...................................................5
PXI-93518 | jytek.com | 1
1. Introduction
1.1 PXI-93518 Overview
1.1.1 What is the PXI-93518
PXI-93518 is an eight ports serial communication module, compatible with RS-422,
RS-485 and RS-232 standards, with fast transient voltage suppression protection
circuit. This protector can effectively suppress lightning and ESD, provide 600W
lightning surge protection power for each line, as well as surge voltage and transient
overvoltage generated on the line for various reasons, and the very small inter pole
capacitance ensures the high-speed transmission of RS-422 / RS-485 / RS-232
interface.
1.1.2 PXI-93518 Features
Eight RS-422 / 485 / 232 communication ports
Baudrate, data bit length, stop bit length (1 or 2 stop bits) and parity mode can
be set
Baud rate:
1. RS-422 and RS-485 support up to 921.6k bps;
2. RS-232 supports up to 115,200 bps.
Receiving circuit with pull-down resistor
Standard serial port operation mode
All ports adopt photoelectric isolation and ± 15kV surge protection
120Ω terminal resistance matching
Operation System Compatibility: Windows 7/ 10
Operating temperature: -40℃～+85℃
Relative Humidity: 0～90%
PXI-93518 | jytek.com | 3
Figure 3 RS-232 Functional Structure
1.1.3 PXI-93518 Connector Pin Assignment
DB62 female connector pin assignment for the PXI-93518.
Pin
RS-232
RS-422
RS-485
Port #
3
OUT1+
A1
Port1
2
OUT1-
B1
50
IN1+
49
IN1-
26
TX1
25
RX1
54
GND
5
OUT2+
A2
Port2
4
OUT2-
B2
48
IN2+
47
IN2-
24
TX2
23
RX2
53
GND
8
OUT3+
A3
Port3
7
OUT3-
B3
46
IN3+
45
IN3-
30
TX3
PXI-93518 | jytek.com | 4
29
RX3
52
GND
10
OUT4+
A4
Port4
9
OUT4-
B4
44
IN4+
43
IN4-
28
TX4
27
RX4
51
GND
14
OUT5+
A5
Port5
13
OUT5-
B5
62
IN5+
61
IN5-
38
TX5
37
RX5
12
GND
16
OUT6+
A6
Port6
15
OUT6-
B6
60
IN6+
59
IN6-
36
TX6
35
RX6
11
GND
19
OUT7+
A7
Port7
18
OUT7-
B7
58
IN7+
57
IN7-
42
TX7
41
RX7
6
GND
21
OUT8+
A8
Por8
20
OUT8-
B8
56
IN8+
55
IN8-
40
TX8
39
RX8
1
GND
Table 1 PXI-93518 Connector Pin Assignment
PXI-93518 | jytek.com | 5
RS-232
RX <1..8>
Receive Data
TX <1..8>
Transmit Data
RS-422
OUT+
<1..8>
Transmit Data Positive
OUT-
<1..8>
Transmit Data Negative
IN+ <1..8>
Receive Data Positive
IN- <1..8>
Receive Data Negative
RS-485
A <1..8>
Data Signal Positive
B <1..8>
Data Signal Negative
Table 2 Notes to Legend in the Pin Definitions
Figure 4 Connector DB62
2. Installation
This chapter describes the configurations of the serial communication module. The
contents in the package and unpacking information that the user should be aware of
are described in the beginning.
PXI-93518 | jytek.com | 6
2.1 What You Have
In addition to this User's Manual, the package includes the following items:
PXI-93518 Serial Communication Interface Module
DB62 Connector
2.2 Unpacking
Your serial communication module contains sensitive electronic components that
can be easily damaged by static electricity.
The module should be done on a grounded anti-static mat. The operator should be
wearing an anti-static wristband, grounded at the same point as the anti-static mat.
Inspect the module carton for obvious damage. Shipping and handling may cause
damage to your module. Ensure there are no shipping and handling damages on the
module before processing.
After opening the module carton, remove the system module and place it only on a
grounded anti-static surface component side up.
Again inspect the module for damage. Press down on all socket IC's to ensure they
are properly seated. Do this only with the module placed on a firm flat surface.
Note: DO NOT APPLY POWER TO THE MODULE IF IT HAS BEEN DAMAGED.
You are now ready to install your PXI Module.
2.3 Installation Procedure
1. Turn off your PXI computer system.
2. Turn off all accessories (printer, modem, monitor, etc.) connected to computer.
3. Select a PXI slot.
4. Before handling the serial communication module, discharge any static buildup on
your body by touching the metal case of the computer. Hold the edge and do not
touch the components.
5. Position the module into the PXI slot selected.
Indice
Altri manuali JYTEK Unità di controllo
JYTEK
JYTEK PXI-67921 Manuale utente
JYTEK
JYTEK PXIe-69529 Manuale utente
JYTEK
JYTEK PXI-67931 Manuale utente
JYTEK
JYTEK USB-61210 Manuale utente
JYTEK
JYTEK JY6301 Manuale utente
JYTEK
JYTEK JY5312 Manuale utente
JYTEK
JYTEK USB-61900 Series Manuale utente
JYTEK
JYTEK JY6302 Manuale utente
JYTEK
JYTEK PCIe-5211 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
