Keller EV-97 Manuale utente

INTRODUCTION

The EV-97 is a microprocessor controlled display unit for use with standard 4 to 20 mA signals for unive r s a l

a p p l i c a t i o n .It is self-powered directly from the two-wire current loop.The measured value is displayed on a

4-digit LCD display, with a maximum range of -1999 to +9999 digits.

The EV-97 is designed for connection to any transmitter with a two-wire 4 to 20mA output signal. The ope-

rating display range can be set up directly without requiring calibration equipment, by simply entering the

maximum and minimum range limits and the decimal point position. These values are entered on three inter-

nal buttons, accessible after removing the front cover. All the programmable parameters are saved on

EEProm, which will store the values for at least 10 years without power.

The EV-97 has a self-diagnostic system which tests for “sensor damage”, “short circuit” and values falling

outside previously set limits.This ensures maximum operational reliability.

Prior to delivery, the EV-97 is tested and calibrated to your instructions. However, make sure you configure

the unit to your specific requirements.Please refer to the section on “Configuration”.

In order to exclude any risk to the operator, the following points should be observed:

a) Immediately switch off the unit in the case of any visible damage or obvious malfunction.

b) Always disconnect the voltage source from the unit before opening it.

c) Standard regulations for opening and safety for electrical light and heavy current equipment have to

be observed, with particular attention having to be paid to national safety regulations (e.g. VDE 0100).

d) When connecting the EV-97 to other transmitters with different wiring (e.g. with GND connected to

protective earth) beware of undesirable voltage potentials.

Attention: When running electric devices, parts of these devices may be highly energised. Unless the

warnings are observed, serious personal injuries or damage to property may result. Skilled person -

nel only should be allowed to work with this unit. For trouble-free and safe operation of the unit, plea -

se ensure professional transport, storage, installation and connection as well as proper operation

and maintenance.

SAFETY ADVICE

EV-97

OPERATING MANUAL

08.2006KELLER

EV-97

ELECTRICAL CONNECTION

Remove the DIN43650 connector from the pressure transmitter.Plug the EV-97 onto the transmitter.

O r ientate as desired. Replace the DIN 43650 connector.Note that the locking screw will have to be replaced

with the longer one supplied.

Supply voltage: The EV-97 is loop-powered from the measuring circuit.

Electric connection and commissioning of the unit must be carried out by trained and skilled personnel.

Wrong connection may lead to the destruction of the display unit, in which case we cannot assume any war -

ranty.Do not exceed the maximum input current rating of 40mA under any circumstances !

08.2006KELLER

PLUG-CONNECTION

This instrument is wired for operation with

all KELLER 2-wire transmitters fitted with

DIN 43650 connectors.

CONNECTIONS (NOTPOLARIZED):

Standard (on Stock) 1 - 2

Series 21/21R/21S 1 - 3

Series 23(S)/25(S)/33(S)/35(S) 2 - 3

The corresponding connections are marked

on the packing.

The polarity is not relevant !

EV-97

Input signal: 4to 20mA (2-wire)

Max. permissible input current: 40 mA

Reverse voltage protection: Polarized installation

Voltage load: Approx. 3 ,5 V

Display: 10 mm high LCD-display

Display range: Starting and end value freely selectable

Maximum display value: 9999 digits

Minimum display value: -1999 digits

Decimal point: Any position

Measuring accuracy: 0,2 % ± 1 digit

Temperature drift: 100 ppm / °C

Measuring interval: Approx. 5 measurements / sec.

Filter:3 stages can be selected

Nominal temperature: 25°C

Ambient temperature: 0 to 50°C

Relative atmospheric humidity: 0 to 80% (non condensing)

Electromagnetic compatibility: In accordance with EN50081-1 and EN50082-1

additional error: < 1 %

Housing: Case: ABS. Front screen: Polycarbonate.

48,5 x 48,5 x 35,5mm (L x W x D)

Connection: Specially designed adaptor for use with DIN 43650

connector (3 pole + earth).

M3 x 75 mm screw supplied.

IP rating: Front side IP65

TECHNICAL SPECIFICATION

FE1:

FE2:

FAULT CODES

Measuring range has been exceeded

This fault code indicates that the measuring range of the A/D converter has been exceeded.

Potential fault cause: Transmitter damaged.

Short-circuit in transmitter connection.

EV-97 incorrectly configured.

Remedies: FE1 will be reset as soon as the measuring values are back within

their permissible range. Please check your transmitter and transmitter

connecting cables.

Measuring values have fallen below permissible range

This fault code indicates that the measuring values of the A/D converter have fallen below the per-

missible range.

Potential fault cause: Transmitter damaged.

Transmitter connection interrupted.

EV-97 incorrectly configured.

Remedies: FE2 will be reset as soon as the measuring values are back within

their permissible range. Please check your transmitter and transmitter

connecting cables.

In case of unacceptable conditions in the system a fault code will be displayed.

Fault codes are defined as follows:

08.2006KELLER

CONFIGURATION

Press button 1, “dP” (decimal point) will be displayed.

Select decimal point position desired using buttons 2 and 3.

Acknowledge decimal point position by pressing button 1. “dP” will be displayed again.

Press button 1 again. “An 4” (display for 4mA) will be displayed.

Buttons 2 and 3 will scroll the display up (button 2) and down (button 3) by 1 digit at a time, for 6 seconds.

The scrolling speed will then increase.

Acknowledge correct value by pressing button 1 again. The new value of “An 4” will be displayed.

Switch to the next parameter by pressing button 1 once again. “An20” will be displayed (display for

20 mA).

Use buttons 2 and 3 to set value to be displayed on the EV-97 for an input signal of 20mA. Acknowledge

value displayed by pressing button 1. “An20” will be displayed again.

Press button 1 once again. “LI” (limit) will be displayed.

Select measuring range limits required using buttons 2 and 3.

0 = Values exceeding / falling below limits are acceptable. (FE1, FE2 displayed for hardware limits).

1 = Values exceeding / falling below limits are not acceptable.(FE1, FE2 displayed for area limits).

Acknowledge selection made by pressing button 1. “LI” will be displayed again. For pressure measuring

t r ansmitters always enter “LI 0”. For transmitters for relative humidity, pH and similar measuring units

a l ways enter “LI 1”.

Press button 1 once again. “FILt” (filter) will be displayed.

Select input filter 0, 1, 2 or 3 required using buttons 2 and 3.

0 = no filter

1 = filter 1 active

2 = filter 2 active

3 = filter 1 and filter 2 active

Filter 1: For filtering the short spikes generated by adjacent relays or contactors, activate “FILt 1”.

Additional delay: approx. 0,5 s.

Filter 2: To prevent “jumping” of the last digit, a phenomenon often found in digital displays, activate

“FILt 2”. This is recommended if the display range exceeds 2000 digits.

Additional display delay: approx. 1 s.

Acknowledge selection made by pressing button 1 again. “FILt” will be displayed.

The adjustment of the EV-97 to the transmitter is now completed. The EV-97 can be switched over to display

the current measuring value by pressing button 1.

Button 2 Button 1 Button 3

EV-97

Altri manuali per EV-97

Indice

Altri manuali Keller Strumento di misura

Keller

Keller LEO RECORD Manuale utente

Keller

Keller ADT1 Manuale utente

Keller

Keller CellaTemp PX 4 Series Manuale utente

Keller

Keller CellaTemp PX1 Series Manuale utente

Keller

Keller LEO 1 Manuale utente

Keller

Keller ITS CellaCast PX 8 Series Manuale utente

Keller

Keller ITS CellaPort PT 11 Series Manuale utente

Keller

Keller CellaTemp PK Series Manuale utente

Keller

Keller LEO RECORD Ei Manuale utente

Keller

Keller ECO 1 Manuale utente

Keller

Keller LEX 1 Manuale utente

Keller

Keller LEO 2 Ei Manuale utente

Keller

Keller LEO-Record-Ei Manuale utente

Keller

Keller CellaTemp PA 4 Series Manuale utente

Keller

Keller CellaTemp PKF Series Manuale utente

Keller

Keller CellaTemp PX1 Series Manuale utente

Keller

Keller CellaCast PA8 Series Manuale utente

Keller

Keller CellaCast PA 80-K002 Manuale utente

Keller

Keller MANO GAUGE Manuale utente

Keller

Keller LEO 5 Manuale utente

Keller

Keller CellaTemp PA 4 Series Manuale utente

Keller

Keller LEO 1 Ei Manuale utente

Keller

Keller LEO 5 Manuale utente

Keller

Keller CellaTemp PR11 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente