Kett MT-700 Manuale utente

Wood Moisture Tester MT-700

Operating manual

Wood Moisture Tester Safety Precautions

Injury or damage to property may result if proper safety procedures are not followed when using the wood moisture

tester.

• Be sure to carefully follow all safety precautions.

Carefully read operating manual.

• Do not use the unit if it is not functioning properly.

Immediately contact our service representative if the unit malfunctions or does not operate properly.

• Meaning of Warning Indications.

The symbols indicated below are used in the operating manual and on the unit itself in order to prevent accidents

due to misuse of the product.These symbols have the following meanings:

This symbol indicates information important for the understand in order to safely operate the product.

Caution

CONTENTS

1. Features............................................................................ 2

2. Specifications.................................................................... 3

3. Part Names ....................................................................... 4

4. Display and Keypad .......................................................... 5

5. Directions .......................................................................... 6

5-1. Before Measuring ................................................... 6

5-2. Measurement Method............................................. 7

5-3. Displaying the average value................................. 10

5-4. Continuous Measurement ..................................... 11

5-5. Performing Moisture Content Bias Adjustment ..... 12

5-6. How to set an alarm value .....................................13

6. Error Code Display...........................................................14

7. Applications and Ranges ................................................. 16

2

1.Features

1. Sixteen wood groups can be measured.

2.The wood group number(HARD:01-09,SOFT:10-16) is displayed.

3.When inactive, the unit will automatically power off after approximately five minutes.

4. When the moisture content exceeds the set upper value, a buzzer sounds.

5.The moisture content can be bias-adjusted for each wood group to correlate with local standards.

3

2. Specifications

Measuring Principle : Electrical Resistance

Applications : Wood

Measuring Range : 5 to 40% (Depends on wood group)

Functions : Average

Auto power off (5minute)

Bias Adjustment (-9.9 ~ +9.9%)

Upper limit alarm setting

Operating Temperature : 0 to 40˚C

Display : LCD

Power Supply : Battery (1.5V, size”AA”alkaline ,6pcs)

Dimensions : 110(W)x 210(D)x 50(H) mm

Weight : 500g

Accessories : Needle probe (1), Spare needle (10), Conductive rubber (2), Wrench (1),

Shoulder strap (1), Battery (1.5V, LR6) (6), Calibration List (2),

Operating Manual (1), Carryingcase (1)

4

3.Part Names

Main body Accessories

Carryingcase

Shoulder strap

Calibration List (2)

Battery(6)

Operating Manual

Needle probe

Conductive rubber (2)Spare needle (10)Wrench

Connector

Display

Control Panel

Needle

Cap

Battery cover(Back)

Needle probe

5

4.Display and Keypad

Wood group number

Battery indicator

Measuring times

"HRD" or "SFT"

Upper limit alarm

Moisture content

Bar graph

Display

Keypad

6

5. Directions

5-1.Before Measuring

1.Load the batteries.

The unit is powered by six LR6 batteries.

Place the batteries in the compartment, taking care to correctly

orient the positive and negative terminls.

• The battery indicator is displayed when the batteries are exhausted.

Replace all six with new batteries.

2.Plug the probe connector into the probe socket on the top of the

unit.

3.Remove the protective cover of the probe.

4.Prepare the sample to be measured before measurement.

Allow it to equilibrate to the ambient temperature of the unit.

7

5-2.Measurement Method

1.Turn on the MT-700.Press the key.All indicators will be

displayed for approximately three seconds.

The wood group number, "HRD" or "SFT" ,"TIMES" ,"%" will be

displayed.

• If this does not happen (as shown in Figure), a problem may exist with

the unit. Please see the error list (Section 6.Error Code Display).

2.Select the wood group from the Calibration List.

Wood group number is from 01 to 09 and from 10 to16.

Exaple :Wood group number 01 to 12

(1) Press the key. Be sure that wood group number is

blinking.

• The part of the display printed in indicates that this part is blinking.

(2) Press the key. Single-digit is blinking.

(3) Press the key. "12", "SFT" will be displayed.

• The wood group number is maintained in memory when the unit's

power is off.

3.Press the probe into the wood to be measured as shown figure.

Place the probe on the wood in the same direction as figure shows,

so that electric current may penetrate at a right angle with the

flow of wood grain.Grasp the grip of the needle probe and insert

the needle up to 7mm into the wood to obtain the intemal mois-

ture content of wood.

• Turn the red mark attached to the metal part of the sensor in the

direction of grain.

•The tip of a sensor needle is a sharp shape.It may cause injury of

the operator or damage the other people by careless handling,

therefore it should be always capped after use.

8

Electric current

Grain direction

Code

Red mark

Indice

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente