Key Digital KD-CX800 Manuale utente
The Experts in Digital Video Technology and Solutions™
Operating Manual
Rev 1 – Oct 2017
Key Digital®Systems :: 521 East 3rd Street :: Mount Vernon, NY 10553
Phone : 914.667.9700 Fax : 914.668.8666 Web : www.keydigital.com
Key Digital®, led by digital video pioneer
Mike Tsinberg, develops and manufactures high quality,
cutting-edge technology solutions for virtually all applications
where high-end video and control are important. Key
Digital®is at the forefront of the video industry for Home
Theater Retailers, Custom Installers, System Integrators,
Broadcasters, Manufacturers, and Consumers.
Control Interface with
IR and RS-232 Over IP Routing
KD-CX800
14
Introduction
KD-CX800 is a control over IP device with three multi-function control ports supporting
bi-directional RS-232, IR out (emitter), IR in (sensor or hardwire), voltage trigger, or
voltage sensor.
About KD-CX800
KD-CX800 is very flexible, with four supported modes of use:
›Mode 1: Control gateway for Enterprise AV Over IP system
»Enables more third-party control options than other HD Over IP systems
»Accepts commands from third-party control systems or Compass Control
®
»Supports generic RS-232, TCP/IP, and IR Key Digital matrix switching command
strings
›Mode 2: Compass Control®Master Controller
»Supports communication to/from licensed iOS and Android devices
»Flexible port configuration (IR, RS-232, trigger, sensor) set in
Compass Navigator
™
program
»IR learner/sensor built-in
»Supports up to two real-time bi-directional RS-232 ports
»TCP/IP device control direct from iOS/Android controller – no ports used
›Mode 3: Third-Party Control via KeyCode Open API
»Cost-effective control expansion with advanced third-party control systems
»Adds reliable hardware interface to network-based control apps
»Enables IR, RS-232, and voltage device control
»Robust API allows for bi-directional communication
›Mode 4: Control Extension via IP
»Carry any supported combination of IR, RS-232, and voltage triggers over the network
»Extends control signals up to 400ft / 121m. Greater distances possible with
adapters.
»Supports systems with or without network switches
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Connections & LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Usage Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Web Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
KeyCode Open API Specification . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Important Product Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
How to Contact Key Digital
®
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
© 2017 Key Digital, Inc. All rights reserved.
Always follow the instructions provided in this Operating Manual.
Please check the Key Digital Website for the most up-to-date Manual.
Please use weblink or the QR code to
download current version of the manual:
http://www.keydigital.com/Downloads/KD-CX800/
KD-CX800_Manual.pdf
32
›Hardwired IR input
»Compatible ports: 1, 2, and 3
»Supports serial (hardwired) IR input with modulated IR signal
»Supported signal level: 0V – 12V
»Supported IR frequency: 20kHz – 100kHz
»NOTE: Supports maximum of one (1) IR input at any time (sensor and
hardwired)
›IR output
»Compatible ports: 1, 2, and 3
»Supported signal level: 0V – 11.4V
»Supported IR frequency: 20kHz – 100kHz
›RS-232
»Compatible ports: 2 and 3
»Supported output signal level: 0V – 11.4V
»Supported input signal level: -12V – 12V
»Does not support H/W Flow Control
»Maximum baud rate is 115200bps
»Supports up to 2 real-time ports
›Voltage Trigger:
»Compatible ports: 1, 2, and 3
»Supported signal level:
»Low: 0V (ground) fixed
»High: 3.3V – 11.4V
»Does not support relay or contact closure functionality
»Does not support extension of digital data
Connections & LEDs
The three multi-function I/O ports can be configured as IR sensor, IR input, IR emitter,
RS-232, voltage trigger, or voltage sensor. However, there are limitations per port:
I/O Port IR Sensor IR Input IR Emitter Serial RS-232 Trigger
1Yes Yes Yes No Yes
2 No Yes Yes Yes Yes
3 No Yes Yes Yes Yes
I/O port configurations:
›Note:
KD-CX800 must be set
to Compass Control Master
Controller mode if you wish to
learn IR remote commands
IR sensor
»Compatible port: I/O Port 1
»Used for IR input or IR learning
»Supported signal level: 0V – 5V
»Supported IR frequency: 20kHz – 60kHz
»IR Sensor (included) pinout:
Pin # (Phoenix) Wire Color Wire Signal
1 Red Power 5V
2 Black Ground
3 White IR Signal
54
Usage Modes
Mode 1:
RS-232/IR/TCP-IP gateway for third-party control of Enterprise AV Over
IP system
›KD-CX800 can be used to control Key Digital’s Enterprise AV Over IP system via
RS-232, TCP-IP, or IR.
›The KD-CX800 will listen for RS-232, TCP-IP, or IR commands from the third-party
control processor/PC and executes the appropriate switching command.
›Default (fixed) I/O port configurations:
»I/O Port 1: IR Sensor IN
»I/O Port 2: RS-232
»I/O Port 3: Compass Control
®
or Key Code Open API
Application Example
KD-CX800
IR Sensor
or
Hard-Wired IR
IR
TCP/IP
TCP/IP
IR/RS-232
Smart Network Switch
TCP/IP
TCP/IP
IR/RS-232 or TCP-IP
CompassControl®, AMX,
Crestron, Control4, Elan,
RTI, Savant, URC, etc. Digital
Signage
HDMI
KD-IP120Tx
Digital
Signage
HDMI
KD-IP120Tx
Flight Info
PC
HDMI
KD-IP120Tx
Computer
HDMI
KD-IP120Tx
KD-IP120Rx
HDMI
KD-IP120Rx
HDMI
KD-IP120Rx
HDMI
KD-IP120Rx
HDMI
KD-IP120Rx
HDMI
KD-IP120Rx
HDMI
›Voltage Sensor
»Compatible ports: 1, 2, and 3:
»Supported signal level:
»Low: -12V – 2V
»High: 2V – 12V
»Uninterrupted voltage sensing updated every 5ms
»Voltage trigger is very low bandwidth. Does not support extension of digital data.
Power
›POE or traditional power supply (screw-type)
»12/V1A (12W) power supply included
»PoE supported on either LAN port
»OK to connect external power supply plus PoE
LAN ports
›KD-CX800 must be connected to the network via hardwire IP connection (no wi-fi)
›The two (2) LAN ports act as an unmanaged network switch
»Support IGMP with connection of IGMP supported network switch
»See Key Digital’s Verified Network Switch document for list of network
switches verified to support Enterprise AV HD Over IP system.
›Supports 10/100BaseT up to 100Mbps
›Supports PoE
›Default IP address: 192.168.1.239
76
›IR command sequence:
»
X,
Video Mode,
Y,
Video Mode
»X = Output / Rx number
»Y = Input / Tx number
»X and Y may be up to 4 button presses (1 – 9999)
»X may be 0 to switch all outputs
»Y may be the UP or DOWN keys to select the next or previous Input
»Y may be the LEFT key to select the pass-thru input (ie 1 to 1, 2 to 2, etc) for
the entire system
»Must be used with “0” as value for X (all outputs)
»If system has more outputs than inputs, the pass-thru begins at
input 1 again
Load completed Enterprise AV system file into KD-CX800
›Open Enterprise AV Tool software
›Select desired system file from Switching drop-down menu
›Press Network Scan to view system Rx and Tx units in respective windows
»Ensure that all Input and Output assignments are completed.
See Creating Switcher System section.
»
Press Download button
»Enter IP address of KD-CX800 as set via web control interface or
device manager software
KD-CX800
TCP/IP
Smart Network Switch
Connectivity
›KD-CX800 must be on the network, connected to either LAN port 1 or LAN port 2
»If controlling via RS-232, connect from third-party control processor or
computer into I/O port 2
»If controlling via IR, connect to IR Sensor or IR In on I/O port 1
›Any Enterprise AV Tx or Rx unit can be connected to LAN port 1 or 2 if needed
›Port 3 is available for Compass Control or KeyCode Open API mode
Supported RS-232 & TCP-IP commands from third-party control system
›Use KD-CX800 as an RS-232, IR, or TCP-IP control gateway
›All commands require a carriage return at the end of the string
›The baud rate is adjustable, with 57,600 bits per second as the default
›KD-CX800 accepts all existing Key Digital matrix switching command strings:
Command Structure Note
SPOxxSIyy Already Supported. Similar to KD-Pro8x8CC.
SPOASIyy All outputs select input yy
SPO<sp>xx<sp>yy Similar to KD-HD16x16ProK
SPO<sp>A<sp>yy
xxByy. Similar to KD-16x16CS. Requires “.”
xxAll.
Bxxyy. Similar to KD-MSW8x4Pro. Requires “.”
Supported IR commands and sequence
›KD-CX800 can be used as an IR gateway to control Key Digital’s Enterprise AV Over
IP system.
›Supported remote: KD-REMOTEHM88 (sold separately)
98
Application Example
KD-CX800
Laptop 1
CAT5e/6
HDMI
HDMI
HDMI
HDMI
Laptop 2
Apple TV
HDMI
HDMI
RS-232
IR Trigger
Network
Router
iOS/Android Controller
Motorized Screen
2nd Display
WiFi
KD-ProCL1
MultiView Switcher
KD-X222
KD-X222
HDMI
Video Conferencing
IR
IR
Additional Links & Info
›Create a Key Digital dealer profile to begin training on the Compass Control®system:
›http://www.keydigital.com/dealerSignUp_v2.asp
Mode 2: Compass Control®Master Controller
›KD-CX800 can be used as a Master Controller for Key Digital’s Compass Control®
system
›KD-CX800 lives on the network and communicates with iOS or Android controllers to
execute IR, RS-232, TCP-IP, or Voltage control commands and sends status values of
connected bi-directional devices for a rich GUI.
›I/O ports, 1, 2, and 3 are configured in any possible type according to the loaded
Compass Navigator project.
›Use as many KD-CX800 units as needed. Can also be used in combination with
other Compass Control master controller units
›KD-CX800 does not support loaded scheduled events or the Compass Control Zigbee
remote.
»Use model KD-MC1000 if those functionalities are needed.
1110
Application Example
Stackable Smart Network Switches
TCP/IP
TCP/IP
TCP/IP
3rd Party Master Controller
KD-IP1080TxKD-IP1080Tx
IR
KD-IP1080Rx
KD-CX800
HDMI
x3 IR
KD-IP1080Rx
KD-CX800
HDMI
x3 IR
KD-IP1080Rx
KD-CX800
HDMI
x3 IR
KD-IP1080Rx
KD-CX800
HDMI
x3
Network
Router
3rd Party
Touchscreen
WiFi
Satellite (x6) Cable (x6)
HDMIHDMI
x6 x6
TCP/IP
Mode 3: Third-Party Control via KeyCode Open API
›KD-CX800 can be controlled by any third-party control system supporting TCP/IP
›Set the desired configuration for each I/O port using the web control interface. See
Web Control Interface section for more information.
»The desired configuration can only be applied to an I/O port using the web
control interface. It is not adjustable via the API commands.
»
Future Key Digital software releases
will support dynamic I/O port
assignment functionality
›KD-CX800 KeyCode Open API commands contain parameters about the executed
command’s format and protocol, as well as the controlled device’s command
›IMPORTANT: Each I/O port has a specific TCP port number assignment.
»Ports numbers are adjustable, but all port numbers must be unique.
›Please see KeyCode Open API Specification section for all commands
1312
›However, future software updates will enable flexible I/O configuration per port
›IMPORTANT: Each I/O port has a specific multicast group ID number assignment
»Multicast group ID numbers are assigned using the web control interface.
»See the Web Control Interface section for more information
»Pair desired IR In or RS-232 RxD ports with desired IR Out or RS-232 TxD port
by assigning the same multicast group ID number.
»IR In or RS-232 RxD at each I/O port must have a unique multicast group ID
number assignment.
»Example:
Installation
Install up to eight units in an equipment rack using KD-RK120PLT. KD-RK120PLT also
houses Enterprise AV Tx or Rx units.
Mode 4: Control Extension via IP
›KD-CX800 can be used to carry IR, RS-232, or voltage trigger over the network
›It can be configured as point-to-point with or without a network switch:
›Future software updates will enable network-based control distribution/matrix
blocks to be created using many units:
›Currently, I/O configurations are fixed (non-adjustable) as follows:
»I/O Port 1: (Default) IR In (sensor or serial IR), or trigger In
»I/O Port 2: (Default) IR out, or trigger out
»I/O Port 3: RS-232
1514
›Image 3: Third-Party Control via KeyCode Open API
›Image 4: Control Extension via IP
Image 1: Setting control mode for Enterprise AV master control usage
Enterprise A/V Control
Web Control Interface
Enter the IP address of your KD-CX800 unit in a web browser to access a web control
interface for unit and I/O port setup
Web control interface home page:
›Displays unit information
›Network setup options, including enable/disable DHCP
Control Mode Setting page
Select desired usage mode for KD-CX800 and apply desired configuration for
each I/O port:
›Image 1: RS-232/IR/TCP-IP gateway for third-party control of Enterprise AV Over
IP system
›Image 2: Compass Control Master Controller
239
1716
Image 3: Setting control mode for KeyCode Open API usage
KeyCode Open API
Image 2: Setting control mode for Compass Control master control usage
Indice
Altri manuali Key Digital Sistema di controllo
