Keysight U1401B Manuale utente
Keysight U1401B
Handheld Multi-Function
Calibrator/Meter
Quick Start
Guide
Contacting Keysight
www.keysight.com/find/assist
(worldwide contact information for
repair and service)
Safety and EMC Information
This instrument is safety and EMC
certified in compliance with:
– IEC 61010-1:2001/
EN61010-1:2001 (2nd Edition)
– Canada: CAN/CSA-C22.2 No.
61010-1-04
– USA: ANSI/UL 61010-1:2004
– IEC61326-2-1:2005/
EN61326-2-1:2006
– Canada: ICES-001:2004
– Australia/New Zealand: AS/NZS
CISPR11:2004
Measurement Category II 150 V,
Pollution Degree 2. Use with
standard or compatible test probes.
Safety Notices
CAUTION
A CAUTION notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly
performed or adhered to, could
result in damage to the product or
loss of important data. Do not
proceed beyond a CAUTION notice
until the indicated conditions are
fully understood and met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly
performed or adhered to, could
result in personal injury or
death. Do not proceed beyond a
WARNING notice until the
indicated conditions are fully
understood and met.
Safety symbols
Earth (ground) terminal
Double insulation
Caution, risk of electric
shock
Caution, risk of danger
CAT II
150V
Category II 150 V
overvoltage protection
2 Keysight U1401B Quick Start Guide
For further safety information details, refer to the
Keysight U1401B Handheld Multi-Function Calibrator/Meter User’s Guide.
Keysight U1401B Quick Start Guide 3
Table of Contents
Recharging the Batteries . . . . . . . . . . . . . . . . . 6
Functions and Features . . . . . . . . . . . . . . . . . . . 8
Input/Output Terminals and Overload
Protection . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Charging the battery . . . . . . . . . . . . . . . . . . . . 11
Performing Voltage Measurements . . . . . . . . 12
Performing Current Measurements . . . . . . . . 14
Performing Resistance Measurement and
Continuity Test . . . . . . . . . . . . . . . . . . . . . . . 16
Performing Temperature Measurements . . . . 18
Frequency and Frequency Counter
Measurements . . . . . . . . . . . . . . . . . . . . . . . 20
Square Wave Output . . . . . . . . . . . . . . . . . . . . 22
Tilt Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4 Keysight U1401B Quick Start Guide
THIS PAGE HAS BEEN INTENTIONALLY LEFT BLANK.
Keysight U1401B Quick Start Guide 5
The following items are included with your
multimeter:
✔Protective holster
✔Rechargeable battery pack (1.2 V NiMH AA
×
8)
✔Power cord and AC power adapter
✔Silicone test leads, alligator clips, and a
yellow test lead for mA simulation
✔Certificate of calibration
✔Printed Quick Start Guide
If anything is missing or damaged, please contact
the nearest Keysight Sales Office.
NOTE
Your multimeter is capable of remote data logging.
To use this feature, you will need an IR-USB cable
(U5481A, purchased separately) and the Keysight
GUI Data Logger Software (downloadable from
www.keysight.com/find/hhTechLib).
WARNING
Ensure the terminal connections are correct for that
particular measurement selection before starting any
measurement. To avoid damage to the device, do not
exceed the input limit.
6 Keysight U1401B Quick Start Guide
Recharging the Batteries
Charge the batteries immediately when the low
battery annunciator starts flashing. It is strongly
recommended that you use only the specified
type of 24 V AC adapter to charge these
rechargeable batteries.
1Power down the instrument and disconnect
all the test leads from the terminals.
2Plug the AC adapter into the jack on the side
panel.
3Set the slide switch at the CHARGE position.
4The red light indicates that the batteries are
being recharged.
Set slide switch at the
CHARGE position
Charging indication
Green: Fully charged
Red: Charging
External AC
adapter jack
Keysight U1401B Quick Start Guide 7
5When the batteries have been fully recharged,
the green light turns on. Remove the AC
adapter and set the slide switch at the Mor
M/S position.
WARNING
Do not discharge a battery by shorting it or subjecting
it to reverse polarity. Do not mix different types of
battery. Make sure a battery is rechargeable before
charging it.
CAUTION
Do not turn the rotary switch while the instrument is
being recharged because a DC 24 V supply is
applied to the charging terminal.
8 Keysight U1401B Quick Start Guide
Functions and Features
Action Steps
Selects AC, DC, or AC+DC
measurement Press
Toggles peak hold mode on and off Press and hold for > 1 s
Freezes the measured value With data hold mode enabled, press
. Press and hold for > 1 s
to exit.
Enters or exits the refresh hold mode With refresh hold mode enabled, press
Enters or exits the dynamic recording
mode Press and hold for > 1 s
Offsets the measured value Press
Selects the measurement range Press
Turns on autorange Press and hold for > 1 s
Turns on dual display Press
Turns on the frequency measurement
function Press
Enables the shifted functions of the
keypad
Press
Toggles the backlight on or off Press and hold for > 1 s
Keysight U1401B Quick Start Guide 9
Selects output mode and range for
voltage and current output With rotary switch at or , and
with mode enabled, press
Selects parameter adjustments for
square wave output
With rotary switch at , and with
mode enabled, press
Selects a digit or the polarity to be
adjusted With mode enabled, press
or
Adjusts a digit or the polarity With mode enabled, press
or
Toggles the output state on and off With mode enabled, press
Action Steps
10 Keysight U1401B Quick Start Guide
Input/Output Terminals and Overload
Protection
The output terminals are protected with DC 30 V
overload protection. The overload protection
limits of the input terminals are shown in the table
below
Functions Overload Protection
AC/DC voltage measurement 250 Vrms
Resistance measurement and continuity test
Temperature measurement
AC/DC current measurement 250 V/630 mA, fast-acting fuse
Altri manuali per U1401B
2
Indice
Altri manuali Keysight Strumento di misura
Keysight
Keysight N2795A Manuale utente
Keysight
Keysight N5247B Manuale utente
Keysight
Keysight Streamline Series Manuale utente
Keysight
Keysight PD1000A Manuale utente
Keysight
Keysight V3500A Manuale utente
Keysight
Keysight PXA N9030A Manuale di installazione e funzionamento
Keysight
Keysight M31 A Series Manuale utente
Keysight
Keysight N5244AU- H29 Manuale di installazione e funzionamento
Keysight
Keysight E4990A Manuale per l'uso e la cura
Keysight
Keysight PNA E8362C Manuale utente
Keysight
Keysight CXA N9000A Manuale di installazione e funzionamento
Keysight
Keysight N9030A Manuale utente
Keysight
Keysight E5080A Manuale utente
Keysight
Keysight U1583B Manuale utente
Keysight
Keysight N2820A Manuale utente
Keysight
Keysight N9010B EXA Manuale di installazione e funzionamento
Keysight
Keysight P937 A Series Manuale utente
Keysight
Keysight B2980A Series Guida all'installazione
Keysight
Keysight N9032B PXA Manuale utente
Keysight
Keysight U1190A Series Manuale utente
