Knick Protos MS 3400-160 Manuale utente
Communication Module
Protos® MS 3400-160
Communication Unit
for Memosens® Sensors
MEMO SENS
www.knick.de
Latest Product Information:
Trademarks
The following trademarks are used in this manual without further marking:
are registered trademarks of Knick Elektronische Messgeräte GmbH & Co. KG, Germany
is a registered trademark of
Endress+Hauser Conducta GmbH & Co. KG, Germany
Knick Elektronische Messgeräte GmbH & Co. KG, Germany
is a registered trademark of Toshiba Corp., Japan
Knick
Elektronische Messgeräte GmbH & Co. KG
P.O. Box 37 04 15
D-14134 Berlin
Phone: +49 (0)30 - 801 91 - 0
Fax: +49 (0)30 - 801 91 - 200
Internet: http://www.knick.de
knick@knick.de
Warranty
Defects occurring within 3 years from delivery date shall be remedied free of charge at our plant
(carriage and insurance paid by sender). Sensors, fittings, and accessories: 1 year.
©2010 Subject to change without notice
Return of Products under Warranty
Please contact our Service Team before returning a defective device. Ship the cleaned device to
the address you have been given. If the device has been in contact with process fluids, it must be
decontaminated/disinfected before shipment. In that case, please attach a corresponding certificate,
for the health and safety of our service personnel.
Disposal
Please observe the applicable local or national regulations concerning the disposal of
“waste electrical and electronic equipment”.
4
6
Table of Contents
Protos MS 3400-160 Module
Warranty ........................................................................................................................................2
Return of Products under Warranty .................................................................................... 2
Disposal .........................................................................................................................................2
Trademarks ................................................................................................................................... 2
Intended Use ..............................................................................................................................10
Safety Information ........................................................................................ 11
Conformity with FDA 21 CFR Part 11 ................................................................................11
Software Version ......................................................................................................................12
Modular Concept .....................................................................................................................13
Short Description .......................................................................................... 14
Short description: FRONT module .....................................................................................14
Short Description: Menu Structure ....................................................................................15
Short Description: BASE Module ........................................................................................17
Terminal Plate MS 3400-160 Module ........................................................... 18
Memosens Cable ............................................................................................ 19
Parameter Setting: Operating Levels .......................................................... 20
Administrator level ..................................................................................................................20
Operator level ............................................................................................................................20
Viewing level ..............................................................................................................................20
Parameter Setting: Locking a Function ...........................................................................21
Configuring the Measurement Display ....................................................... 22
Documenting Parameter Setting .......................................................................................24
ProgaLog 3000 Software (Option)
for Configuration and Documentation ....................................................... 26
Module Configuration: Operating Mode .........................................................................30
Memosens PH Parameter Setting ................................................................ 31
Activating the Cal Tolerance Band .....................................................................................34
Calibration / Adjustment .............................................................................. 38
Adjustment .................................................................................................................................39
Calibration methods ...............................................................................................................40
Temperature compensation .................................................................................................41
Selecting a calibration method ...........................................................................................42
7
Table of Contents
Protos MS 3400-160 Module
Maintenance .................................................................................................. 52
Sensor monitor .........................................................................................................................52
Temp probe adjustment ........................................................................................................52
Diagnostics Functions ............................................................................................................53
Message list ................................................................................................................................53
Logbook .......................................................................................................................................53
Sensor monitor .........................................................................................................................54
Cal record ....................................................................................................................................54
Sensor network diagram .......................................................................................................55
Sensor wear ................................................................................................................................55
Calibration timer .......................................................................................................................56
Adaptive calibration timer ....................................................................................................56
Tolerance adjustment .............................................................................................................56
Memosens ORP Parameter Setting .............................................................. 57
ORP calbration/adjustment .................................................................................................62
Temperature dependence measured against SHE ..................................... 63
Maintenance .................................................................................................. 64
Sensor monitor .........................................................................................................................64
Temp probe adjustment ........................................................................................................64
Diagnostics Functions ................................................................................... 65
Message list ................................................................................................................................65
Logbook .......................................................................................................................................65
Sensor monitor .........................................................................................................................66
Cal record ....................................................................................................................................67
Memosens OXY Parameter Setting ..................................................................................69
Calibration / Adjustment .............................................................................. 73
Adjustment .................................................................................................................................74
Recommendations for calibration .....................................................................................75
Selecting a calibration method ...........................................................................................76
Automatic calibration in water ...........................................................................................78
Automatic calibration in air ..................................................................................................80
Product Calibration (Calibration with Sampling) ........................................................82
8
Table of Contents
Protos MS 3400-160 Module
Data entry of premeasured sensors .................................................................................84
Zero correction ..........................................................................................................................85
Memosens OXY Maintenance ...................................................................... 86
Sensor monitor .........................................................................................................................87
Cal record ....................................................................................................................................88
Sensor network diagram OXY .............................................................................................88
Memosens COND Parameter Setting ........................................................... 89
Concentration Table ................................................................................................................95
USP Function .................................................................................................. 96
pH Value Calculation ..................................................................................... 97
Configuring a Calculation Block ................................................................. 101
Calibration / Adjustment ............................................................................ 103
Adjustment .............................................................................................................................. 104
Temperature compensation .............................................................................................. 105
Selecting a calibration method ........................................................................................ 106
Sensor calibration ................................................................................................................. 115
Memosens COND Maintenance .................................................................. 116
Sensor monitor ...................................................................................................................... 117
Cal record ................................................................................................................................. 118
CONDI Parameter Setting (SE 670 Sensor) ................................................ 119
Concentration Table ............................................................................................................. 125
Calibration / Adjustment ............................................................................ 127
Adjustment .............................................................................................................................. 128
Temperature compensation .............................................................................................. 129
Selecting a calibration method ........................................................................................ 130
Calibrating the sensors ....................................................................................................... 139
CONDI Maintenance ................................................................................... 140
Sensor monitor ...................................................................................................................... 141
Cal record ................................................................................................................................. 142
Calculation Blocks (for all process variables) .............................................................. 143
Logbook ................................................................................................................................... 145
Factory setting ....................................................................................................................... 145
9
Table of Contents
Protos MS 3400-160 Module
To configure a current output .......................................................................................... 146
Current Outputs: Characteristics ..................................................................................... 147
Output Filter ............................................................................................................................ 149
NAMUR Signals: Current Outputs ................................................................................... 150
NAMUR Signals: Relay Contacts ....................................................................................... 151
Relay Contacts: Protective Wiring ................................................................................... 152
Relay contacts, usage .......................................................................................................... 153
Relay Contacts: Sensoface Messages ............................................................................. 154
Rinse Contact .......................................................................................................................... 155
Icons in the measurement display .................................................................................. 156
Limit Value, Hysteresis, Contact Type............................................................................. 156
OK1, OK2 Inputs: Specify Level ........................................................................................ 157
Switching Parameter Sets via OK2 .................................................................................. 158
Select Parameter Set (A, B) via OK2 Input .................................................................... 158
Signaling Active Parameter Set via Relay Contact .................................................... 158
Specifications ............................................................................................... 159
Index ............................................................................................................ 161
10
Intended Use
The module provides an RS-485 interface for connecting Memosens sensors.
An analog current input can accept a signal from a pressure transmitter for
pressure compensation of oxygen sensors. A galvanically isolated switching
input allows the connection of monitoring equipment, such as a flow monitor-
ing system.
Current input
(OXY: pressure transmitter
or ow, for ex.)
Switching input
(e.g. ow monitoring)
1
2
3
4
5
7
9
11
13
Shield
Memosens
sensor
Indice
Altri manuali Knick Unità di controllo
Knick
Knick Protos LDO 3400-170 Manuale utente
Knick
Knick Protos Compa 3400(X)-081 Manuale utente
Knick
Knick Protos 3400 Series Manuale utente
Knick
Knick Protos OXY 3400-067 Manuale utente
Knick
Knick Protos COMFF 3400-085 Manuale utente
Knick
Knick Protos LDO 4400-170 Manuale utente
Knick
Knick Protos II 4400 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
