Kobold NSC Manuale utente
Operating Instructions
For
Capacitance Level
Model: NSC
NSC
Page 2 DT0307
1.Content
1. Content .........................................................................................................2
2. Note ..............................................................................................................3
3. Instrument Inspection....................................................................................3
4. Description....................................................................................................3
5. Operating principle........................................................................................3
6. Mechanical connection..................................................................................4
7. Electrical connection.....................................................................................5
8. Adjustment....................................................................................................6
8.1 Module replacement ............................................................................8
9. Models ..........................................................................................................9
10. Technical Data............................................................................................10
11. Safety Instructions (ATEX)..........................................................................11
12. Installation in classified zone (ATEX)..........................................................13
13. Label Description (ATEX)............................................................................13
14. Models ATEX..............................................................................................14
15. Declaration of conformance ( ATEX )..........................................................15
16. Declaration of conformance........................................................................16
17. ATEX Certificate..........................................................................................17
18. NOTES........................................................................................................21
Manufactured by:
Kobold Mesura S.L.U
Avda. Conflent, 68 nave 15
08915 Badalona
Tel.: +34 93 460 38 83
Fax: +34 93 460 38 76
Internet: www.kobold.com
june 2017
NSC
DT0307 Page 3
2.Note
Please read these operating instructions before unpacking and putting the unit
into operation. Follow the instructions precisely as described herein.
The devices are only to be used, maintained and serviced by persons familiar
with these operating instructions and in accordance with local regulations
applying to health & safety and prevention of accidents.
3.Instrument Inspection
Instruments are inspected before shipping and sent out in perfect condition.
Scope of delivery
The standard delivery includes:
Capacitive Level Monitor NSC
Cable gland 1x M20x1,5 ( 2 atex version )
Operating Instructions
4.Description
This level switch instruments for solids NSC, has been designed to be used in all
applications where the level of the solid must be detected in tanks and silos.
5.Operating principle
The NSC sensor together with the wall of the tank is a capacitor.
The dielectric constant of this capacitor is the air when the product (media) doesn’t
reach the sensor. When the product covers the sensor, the dielectric constant is
the product one. The electronic circuit of the NSC detects this change and
activates an output relay.
NSC
Page 4 DT0307
6.Mechanical connection
The NSC has a thread of 1”BSP male. The sensitive part of the probe goes from
the PP isolator to the end of the probe.
Check that lenght of probe is according the level to be detected.
When the housing is installed in the outdoor it is recommended to protect it against
sun radiation and rain by means of a small roof.
When installing the probe of the NSC by means of an extension sleeve, the max.
lenght of this sleeve must be 70mm to avoid short-circuit in between the tank and
the probe due to product accumulation inside the sleeve.
NSC
DT0307 Page 5
7.Electrical connection
VERY IMPORTANT
Be sure that power supply corresponds with the indicated in the equipment’s
label.
GREEN led lighting indicates that equipment is powered
RED led lighting indicates that output relay is activated.
Using SELECTOR 1, you can choose relay operation NO or NC when the
product covers the probe.
Protection fuse of 0.5mA must be put in serial with supply line.
Ground terminal is internally tied to the connection thread.
Be sure that ground line has same potential than ground of thank.
If you are not sure, please do not connect the ground terminal since the
instrument could be damaged.
NSC
Page 6 DT0307
8.Adjustment
After installation and connection verification, we proceed to AJUST SENSITIVITY to fit
the NSC with the tank and the product to measure.
Check that product doesn’t reach the probe. Power supply GREEN LED must be ON
1. Put DIP-SWITCH 1 to “MAX” position.
2. Turn the “SENSITIVITY ADJUSTMENT screw” clockwise until RED LED
lights.
NSC
DT0307 Page 7
3. Turn slowly the “SENSITIVITY ADJUSTMENT screw” counter clockwise until
RED LED switches off.
4. Turn 360º more counter clockwise to avoid a critical adjustment. In case of
sticky products it is recommended to increase this adjustment.
The instrument is now adjusted. When product will reach the probe relay will be
activated and RED LED will light.
If we want the relay to work the REVERSE, put DIP-SWITCH 1 to “MIN”.
Check that no product remains on the probe when unloading the tank.
NSC
Page 8 DT0307
8.1 Module replacement
MODCAP modules are delivered with DIP-SWITCHES 2, 3 and 4 adjusted with its own
probe. In case of replacement, following procedure must be done with the probe free of
product:
1. With DIP-SWITCH 1 to “MAX” and 2, 3 and 4 to “MIN”, turn the multiturn
potentiometer totally to clockwise (20 turns). RED LED will switch ON.
2. In case that RED LED doesn’t lights, move DIP-SWITCH 4 (drawing 1) to
ON. If RED LED still remains OFF, do same with DIP SWITCH 3 (drawing 2)
and finally with DIP-SWITCH 2 (drawing 3) until RED LED finally lights.
Drawing 1 Drawing 2 Drawing 3
3. Once DIP-SWITCHES are correctly settled the SENSITIVITY ADJUSTMENT
must be done (chapter 8).
NSC
DT0307 Page 9
9.Models
There are 2 basic models of NSC:
NSC..R
The probe is a rod made of st.st. and covered with PTFE.
It is used for minimum and intermediate level detection.
It is produced a Standard version with a sensor of a maximum length of 3000mm
NSC..C
The probe is a flexible cable covered with PP, with a st.st. weight at the end. It is
used for maximum level detection.
NSC
Page 10 DT0307
10. Technical Data
Note: Kobold Mesura makes every attempt to ensure the accuracy of these
specifications but reserves the right to change them at any time.
Supply: 24, 110, 230 Vac ó 18 a 36 Vdc.
Max. Power: 1 VA
Process connection: 1G
Other connections: DIN Flange, clamp, etc.
Power supply and relay status LED.
Polycarbonate housing IP.65.
Ambient Temperature: -20…+60 ºC.
Process Temperature: -20…+80ºC.
Cable gland: 1 x M20x1,5 ( standard version ), 2 x M20x1,5 ( atex version ).
Relay Output: max. 250 Vca 1 A.
Sensitivity adjustment by multi-turn trimmer.
Vdc polarity reverse protection.
Minimum or maximum security adjustment.
Rod version probe (NSC.R) covered with PTFE. Flexible cable st.st. probe
(NSC.C) or steel covered with PP.
ONLY ATEX VERSION:
Certified:
ATEX II 2/1 tD[iaD]iaD A21/20 IP65 T85 ºC Ta: -20ºC/+60ºC
Aluminium housing IP.65
Indice
Altri manuali Kobold Strumento di misura
Kobold
Kobold DAG-M1V Series Manuale utente
Kobold
Kobold DON Series Manuale utente
Kobold
Kobold DAG-S4F Series Manuale utente
Kobold
Kobold URM Manuale utente
Kobold
Kobold KSK Manuale utente
Kobold
Kobold DTK Manuale utente
Kobold
Kobold HND-PS01 Manuale utente
Kobold
Kobold URB Manuale utente
Kobold
Kobold DSS Series Manuale utente
Kobold
Kobold NMF Manuale utente
Kobold
Kobold MAS Manuale utente
Kobold
Kobold OVZ Manuale utente
Kobold
Kobold DAG-A4B Series Manuale utente
Kobold
Kobold DOG-4 Manuale utente
Kobold
Kobold DWU 5 Series Manuale utente
Kobold
Kobold SZM Manuale utente
Kobold
Kobold TIN-SS Manuale utente
Kobold
Kobold KSV Manuale utente
Kobold
Kobold KFR-1000 Series Istruzioni per l'installazione
Kobold
Kobold NBK-19 Manuale utente
