KTI Networks KFS-0540 Manuale utente
-1-
KFS-0540 Ver.B
Industrial 5-Port Fast Ethernet Switch
Installation Guide
DOC.171103
-2-
(C) 2017 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form
or by any means or used to make any directive work (such as translation or transformation) without permission
from KTI Networks Inc.
KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to
time without obligation on the part of KTI Networks Inc. to provide notification of such revision or change.
For more information, contact:
United States KTI Networks Inc.
P.O. BOX 631008
Houston, Texas 77263-1008
Phone: 713-2663891
Fax: 713-2663893
URL: http://www.ktinet.com/
International Fax: 886-2-26983873
URL: http://www.ktinet.com.tw/
-3-
The information contained in this document is subject to change without prior notice. Copyright (C) All Rights
Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
including the interference that may cause undesired operation.
CE NOTICE
Marking by the symbol indicates compliance of this equipment to the EMC directive of the European
Community. Such marking is indicative that this equipment meets or exceeds the following technical
standards:
EMC Directive of 2014/30/EU
EN 61000-6-4
EN 55032 Class A
CISPR 32
EN 61000-3-2
EN 61000-3-3
EN 61000-6-2
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
-4-
Table of Contents
1. Introduction...................................................................................................................................5
1.1 Features..............................................................................................................6
1.2 Product Panels....................................................................................................6
1.3 LED Indicators.....................................................................................................7
1.4 Specifications......................................................................................................7
2. Installation.....................................................................................................................................9
2.1 Unpacking...........................................................................................................9
2.2 Safety Cautions...................................................................................................9
2.3 Mounting the Switch to a Din-Rail......................................................................10
2.4 Mounting the Switch on a Panel........................................................................12
2.5 Applying Power.................................................................................................14
2.5.1 Using Terminal Blocks.................................................................................... 15
2.5.2 Using DC Power Jack ....................................................................................16
3. Making LAN Connections..........................................................................................................17
3.1 10/100 Copper Ports.........................................................................................17
3.2 LED Indication................................................................................................... 17
-5-
1. Introduction
The switch provides five 10/100Mbps copper ports for connections to Ethernet and Fast Ethernet devices. With
the featured auto-negotiation function, the switch can detect and configure the connection speed and duplex
automatically. The switch also provides auto MDI/MDI-X function, which can detect the connected cable and
switch the transmission wire pair and receiving pair automatically. This auto-crossover function can simplify
the type of network cables used.
For industrial environment, the device is designed with the following enhanced features exceeding that of
commercial Ethernet switches:
High and wide operating Temperature
Power input interface: Industrial screw terminal block and DC power jack for external commercial power
adapter as option
Screw panel and DIN rail mounting support for industrial enclosure
Industrial-rated Emission and Immunity performance
-6-
1.1 Features
Auto MDI/MDI-X crossover function on the copper port
Support IEEE 802.3x flow control for full-duplex operation
Support Back-pressure flow control for half-duplex operation
Wide operating temperature range for temperature critical environment
Support DIN-rail mounting and panel mounting
Provide two power input types to meet more application needs
Accept wide power input voltage range for application flexibility
Industrial-rated Emission and Immunity performance
1.2 Product Panels
The following figure illustrates the panels of the switch:
-7-
1.3 LED Indicators
LED Function
POWER Power status
1 - 5 Port 1 –Port 5
LINK Link and activity status (Port 1 - Port 5)
100M 100Mbps speed status (Port 1 - Port 5)
1.4 Specifications
10/100 Copper Ports
Compliance IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX
Connectors Shielded RJ-45 jacks
Pin assignments Auto MDI/MDI-X detection
Configuration Auto-negotiation or software control
Transmission rate 10Mbps, 100Mbps
Duplex support Full/Half duplex
Network cable Cat.5 UTP up to 100 meters
Switch Functions
Forwarding & filtering Non-blocking, full wire speed
Switching technology Store and forward
Maximum packet length 1536 bytes
MAC Addresses Table 2K entries
Port configuration Auto-negotiation for speed and duplex
Flow control IEEE 802.3x pause frame base for full duplex operation
Back pressure for half duplex operation
Storm control Broadcast packets are dropped when large consecutive broadcast packets are
received.
DC Power Input
Screwed terminal block 3P (Vin+, Vin-, Chassis Ground)
DC Jack Connector -D 6.3mm / + D 2.0mm
Operating Voltages +7 ~ +30VDC
Power Consumption 2.2W max.
Mechanical
Dimension (base) 40 x 80 x 95 mm (WxDxH)
Housing Enclosed metal with no fan
-8-
Mounting Din-rail mounting
Panel mounting (optional)
Environmental
Operating Temperature Typical -35oC ~ +70oC
Storage Temperature -40oC ~ +85oC
Relative Humidity 10% ~ 90% non-condensing
Electrical Approvals
FCC Part 15 rule Class B
CE EN 55032 Class A
EN 61000-6-4
CISPR 32
EN 61000-3-2
EN 61000-3-3
EN 61000-6-2
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
IEC 61000-4-11
VCCI Class A
Safety LVD, IEC60950-1
Mechanical Approvals
IEC 60068-2-64 Fh Vibration
IEC 60068-2-6 Fc Vibration 5~200Hz 1G
IEC 60068-2-27 Ea Shock 50G test,
IEC 60068-2-27 Ea Bump 25.5G test
-9-
2. Installation
2.1 Unpacking
The product package contains:
The switch unit for Din-rail mounting
One product CD-ROM
2.2 Safety Cautions
To reduce the risk of bodily injury, electrical shock, fire and damage to the product, observe the following
precautions.
Do not service any product except as explained in your system documentation.
Opening or removing covers may expose you to electrical shock.
Only a trained service technician should service components inside these compartments.
If any of the following conditions occur, unplug the product from the electrical outlet and replace the part
or contact your trained service provider:
- The power cable, extension cable, or plug is damaged.
- An object has fallen into the product.
- The product has been exposed to water.
- The product has been dropped or damaged.
- The product does not operate correctly when you follow the operating instructions.
Do not push any objects into the openings of your system. Doing so can cause fire or electric shock by
shorting out interior components.
Operate the product only from the type of external power source indicated on the electrical ratings label. If
you are not sure of the type of power source required, consult your service provider or local power
company.
-10-
2.3 Mounting the Switch to a Din-Rail
In the product package, a DIN-rail bracket is provided or has been installed for mounting the switch in a
industrial DIN-rail enclosure.
The steps to mount the switch onto a DIN rail are:
1. Install the mounting bracket onto the switch unit with screws as shown below:
2. Attach bracket to the lower edge of the DIN rail and push the unit upward a little bit until the bracket can
clamp on the upper edge of the DIN rail.
Indice
Altri manuali KTI Networks Interruttore
KTI Networks
KTI Networks KGS-0820 Manuale utente
KTI Networks
KTI Networks KGS-500 Ver.D Manuale utente
KTI Networks
KTI Networks KSD-541 Manuale utente
KTI Networks
KTI Networks KGD-802 Manuale utente
KTI Networks
KTI Networks KGS-1064-BP Manuale utente
KTI Networks
KTI Networks KGS-1064-HP Manuale utente
KTI Networks
KTI Networks KF-8D Manuale utente
KTI Networks
KTI Networks KGS-1060 Manuale utente
KTI Networks
KTI Networks KGS-2416 Manuale utente
KTI Networks
KTI Networks KGS-2461-S Manuale utente
KTI Networks
KTI Networks KS-116 Manuale utente
KTI Networks
KTI Networks KS-105F-B Series Manuale utente
KTI Networks
KTI Networks KGS-2422-TG Series Manuale utente
KTI Networks
KTI Networks KSD-541 Manuale utente
KTI Networks
KTI Networks KS-108F Manuale utente
KTI Networks
KTI Networks KGS-2421 Manuale utente
KTI Networks
KTI Networks KS-108F Manuale utente
KTI Networks
KTI Networks DH-8T Manuale utente
KTI Networks
KTI Networks KGS-2800 Manuale utente
KTI Networks
KTI Networks KS-105F-T Manuale utente
