LI-COR LI-800 Guida

1. Turn the LI-800 off. Remove the six screws on the LI-800 top panel and remove the cover.

2. Unscrew the tube retaining nuts on the inner air port fittings. Remove the tubing from both air ports. Leave the tubing connected

to the source and detector housings.

3. There are ribbon cables (Figure 1 below) connected to the circuit boards on the source and detector housings. Pull straight out on

the connector that is attached to each ribbon cable. The optical bench can now be removed from the foam casing.

Source Detector

Air In Air Out

PCBPCB

Optical Bench

Hose Barb

Bev-a-line Tubing

Ribbon Cable

Connector

4. There are four screws on the source and detector circuit boards that must be removed. Remove the four screws in the corners of

the boards, as shown below (they are slightly larger than the other four screws). Do not remove the remaining four screws.

Remove these

4 screws

5. The source and detector housings (with attached circuit boards) can now be removed. The bench will appear as shown below. Be

careful not to lose the O-ring on either end of the bench.

O-ring

Top View

End View

6. Install the source and detector housings on the gold-plated optical path cylinder. Make sure that both source and detector hous-

ings have an O-ring installed, as shown in Step 5 above. The orientation of the cylinder is not important; either end can be

inserted into the source or detector housing. Note: There is no need to grease the O-ring; simply press into place.

LI-800 GasHound

Source/Detector Replacement Instructions

7. Carefully remove the 10-pin connector that was attached to the source housing circuit board from the main circuit board. Reat-

tach the 10-pin connector to one of the connectors shown below, depending on the length of the optical bench being installed.

Fuse

LEDs

Connector for 2”

optical bench

Source Detector

Connector for 5.5"

optical bench (not

shown, beneath

tubing)

Figure 4. Location of 10-pin connectors for 5.5" and 2" optical benches.

8Install the bench with the source side on the left as you face the front of the instrument.

9. Reattach the 10-pin connectors to the source and detector housing circuit boards. Reattach the Bev-a-line tubing to the hose barbs

on the source and detector housings, and to the flow in and out ports, if necessary.

10. Re-assemble the LI-800 case. Make sure that the foam insulation on the inside top cover is positioned over the optical bench; it is

required for thermal stability.

11. Perform zero and span calibrations as described in the LI-800 Instruction Manual Section 3, Calibration Window.

LI-COR, inc. ●Environmental Division ●4421 Superior Street ●P.O. Box 4425 ●Lincoln, Nebraska 68504 USA

Phone: 402-467-3576 ● FAX: 402-467-2819

Toll-free 1-800-447-3576 (U.S. & Canada)

E-mail: envsales@env.licor.com

Internet: http://www.licor.com

AKC101

Altri manuali per LI-800

Indice

Altri manuali LI-COR Strumento di misura

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente