Lightolier C6CW SERIES Manuale utente

GASKET

CLEAT

MULLION

OUTLET BOX SCREWS

MOUNTING PLATE

CANOPY

1/4-20 BOLTS

CLEAT

FIG. 1 FIG. 2

FIG. 3

FIG. 4

CAUTION: For wet locations, in accordance with Underwriters Laboratories

requirements, a line of caulking compound such as acrylic or silicone must be

placed around the perimeter of CANOPY to seal water away from the

outlet box and back openings.

INSTALLATION OF WALL CYLINDER TO OUTLET BOX

(Fig. 1, 2, 3, & 4)

STEP 1: Attach MOUNTING PLATE to outlet box with OUTLET BOX

SCREWS.

STEP 2: Pass supply leads through opening in CANOPY and CLEAT.

STEP 3: Attach CANOPY, CLEAT/GASKET to MOUNTING PLATE with (2)

¼-20 BOLTS.

STEP 4: Make Connections. Bare Copper and/or green insulation wire(s)

must be connected to SUPPLY GROUND. Connect WHITE BALLAST LEAD

to NEUTRAL (WHITE) SUPPLY LEAD. Connect BLACK BALLAST LEAD to

HOT SUPPLY LEAD. Use wire nuts (local hardware items).

STEP 5: Install SET SCREWS loosely. Place cylinder over CLEAT and

tighten (2) SET SCREWS.

INSTALLATION OF WALL CYLINDER TO POST OR OTHER

VERTICAL SURFACE MOUNTING (Fig. 2, 3 & 4)

STEP 1: CLEAT can also be mounted directly to any flat surface

such as MULLION. In this case, use of CANOPY is optional. Bring

supply leads through CLEAT and install CLEAT to wall. For wet

locations, in accordance with Underwriters Laboratories requirements,

a line of caulking compound such as acrylic or silicone must be

placed around the perimeter of EXTRUDED ARM to seal water away

from the wireway and back openings.

STEP 2: Proceed with Step 4 and 5 above.

INSTALLATION OF REFLECTOR TRIM TO CYLINDER (Fig. 4)

Follow installation instructions in Reflector Trim Instruction Sheet IS:C4T4V.

CAUTION:

 DO NOT ENERGIZE THE LAMP UNTIL REFLECTOR

TRIM IS COMPLETELY INSTALLED.

 INSTALL ONLY T-6 TUBULAR SINGLE-ENDED

CREAMIC ARC TUBE METAL HALIDE LAMP.

A COMPANY

631 Airport Road, Fall River, MA 02720

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain

these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:C6CW

Page 1 of 2

A0604

INSTALLATION PROCEDURE FOR: C6CW SERIES 6” DIA. H.I.D. WALL MOUNT CYLINDER

USED WITH C6T6V SERIES FLANGLESS REFLECTOR TRIM (ORDER SEPARATELY)

WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURES’ REFLECTOR

TRIMS MAY VOID THE UNDERWRITERS LABRATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

APERTURE CONE

ASSEMBLY

FIG. 5

TO REPLACE BALLAST (Fig. 5 & 6)

Before changing the ballast, switch off the main power supply to the fixture.

STEP 1: Remove APERTURE CONE ASSEMBLY from REFLECTOR

HOUSING by grasping inside of cone and pulling down.

STEP 2: Remove lamp.

STEP 3: Pull REFLECTOR HOUSING down until CLIPS stop at the bottom

lip of LOWER HOUSING. Press CLIPS inward to remove REFLECTOR

HOUSING.

STEP 4: Detach LAMPHOLDER from REFLECTOR HOUSING by

squeezing LAMPHOLDER SPRING.

STEP 5: Remove WING NUTS, then separate UPPER HOUSING from top

of Lower HOUSING to access BALLAST/PLATE ASSEMBLY.

STEP 6: Turn SCREW counterclockwise to lossen SUPPORT BRACKET.

Repeat with other (2) screws. Carefully remove BALLAST/PLATE

SSEMBLY from UPPER HOUSING.

STEP 7: Detach BALLAST SUPPORT BRACKET by removing (2)

BALLAST SUPPORT BRACKET SCREWS.

STEP 8: Replace BALLAST. Reattach BALLAST/BALLAST SUPPORT

BRACKET, BALLAST/PLATE ASSEMBLY to UPPER HOUSING.

STEP 9: Align STUDS with holes in LOWER HOUSING, then tighten firmly

with WING NUTS.

STEP 10: Reverse installations from Step 4 to Step 1. For additional

instructions if needed, see Reflector Trim Instruction Sheet IS:C4T4V.

TO REPLACE LAMP (Fig. 5 & 6)

Before replace the lamp, switch off the main power supply to the fixture.

STEP 1: Remove APERTURE CONE ASSEMBLY from REFLECTOR

HOUSING by grasping inside of cone and pulling down.

STEP 2: Replace lamp. Follow lamp manufacturer’s directions for proper

care and handing of lamp.

STEP 3: Replace cone into reflector housing.

A COMPANY

631 Airport Road, Fall River, MA 02720

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To

assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:C6CW

Page 2 of 2

A0604

INSTALLATION PROCEDURE FOR: C6CW SERIES 6” DIA. H.I.D. WALL MOUNT CYLINDER

USED WITH C6T6V SERIES FLANGLESS REFLECTOR TRIM (ORDER SEPARATELY)

WARNING: USE ONLY REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURES’ REFLECTOR

TRIMS MAY VOID THE UNDERWRITERS LABRATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.

Indice

Altri manuali Lightolier Apparecchio di illuminazione

Lightolier

Lightolier Coffaire II CFH1GPF Manuale utente

Lightolier

Lightolier VTS2GPK332 Manuale utente

Lightolier

Lightolier Lytecaster 1113CFL Manuale utente

Lightolier

Lightolier Lytecaster 1004ICR Manuale utente

Lightolier

Lightolier SOF-TECH Istruzioni per l’uso

Lightolier

Lightolier Lytespan 8680 Manuale utente

Lightolier

Lightolier Calculite ProSpec PB4P3075 Manuale utente

Lightolier

Lightolier ProSpec 26230 Manuale utente

Lightolier

Lightolier Calculite C3MRD Manuale utente

Lightolier

Lightolier GUARDSMAN GV4WB332 Manuale utente

Lightolier

Lightolier LL4MF8LX254 Manuale utente

Lightolier

Lightolier STA 1'x4' 1 LAMP Manuale utente

Lightolier

Lightolier QVL2GPFSS2FT Manuale utente

Lightolier

Lightolier QVS2GSDOS2FT Manuale utente

Lightolier

Lightolier 16FR2X6 Manuale utente

Lightolier

Lightolier Lytecaster 2000AIC Manuale utente

Lightolier

Lightolier KD SERIES HO Manuale utente

Lightolier

Lightolier Calculite ProSpec PB3A7050 Manuale utente

Lightolier

Lightolier VR PARABOLIC VRA2G16LV2FT Manuale utente

Lightolier

Lightolier Decorative Arco 4511 Manuale utente

Lightolier

Lightolier Lytespan 6170 Manuale utente

Lightolier

Lightolier Lytespan 8608 Manuale utente

Lightolier

Lightolier Calculite ProSpec PA1A7050 Manuale utente

Lightolier

Lightolier Calculite ProSpec PA3H3870 Manuale utente

Manuali Apparecchio di illuminazione popolari di altre marche

Emos

Emos CLASSIC ZY1431T Manuale utente

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuale utente

Hedler

Hedler C 12 silent Manuale utente

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuale utente

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuale utente

Lightmaxx

Lightmaxx Shaft 5R Manuale utente

Triarch

Triarch 31083 Manuale utente

Philips

Philips 32614 Series Manuale utente

IKEA

IKEA TIVED Manuale utente

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuale utente

Martin

Martin MAC 250 Krypton Manuale utente

Cooper Lighting

Cooper Lighting Halo L3232E Manuale utente

Stageline

Stageline ODW-2410RGBW Manuale utente

Light Sky

Light Sky Tornado Series Manuale utente

ArtFox

ArtFox Beam 15R extreme Manuale utente

GLG

GLG multispot 330 Manuale utente

Home Accents Holiday

Home Accents Holiday TY052-1924-1 Manuale utente

SELF Electronics

SELF Electronics FLEX Manuale utente