Lilin iMEGAPRO IPR7922E Manuale utente
LR7922E
IPR7922E
D/N 1080P HD Infrared IP Camera
D/N 1080P HD Infrared IP Camera
66-LR7922CSM
Quick Installation Guide
CAUTION
Do not drop or strike this equipment
Do not install the equipment near any naked flames or heat
sources
Do not expose this unit to rain, moisture, smoke or dust
environment
Do not cover the opening of the cabinet with cloth and plastic
or to install this unit in poor ventilated places. Allow 10cm
between this unit and its surroundings
Do not continue to operate the unit under abnormal
conditions such as detection of smoke, strange smell or no
display on screen while power is turned on
Do not touch the power connection with wet hands
Do not damage the power cord or leave it under pressure
Do not operate this unit near magnet, speaker system, etc., to
avoid unnecessary magnetic interference
onnection cables should be grounded properly
The ITE is to be connected only to PoE networks without
routing to the outside plant.
L’ITE ne doit être connecté que sur un réseau PoE sans
routage vers l’ali entation extérieure.
Product Overview
Unit: mm
English
- 1 -
① Front over
② Rear over
③ Bracket
④ Pan Adjustment Screw
⑤ Tilt Adjustment Screw
⑥ RJ-45 Network Port (Support PoE)
⑦ D 12V Power Input Jack (D 12V±10%)
⑧ Reset Key
To restore the server to factory default setting.
⑨ Micro SD ard Slot
⑩ Lens
⑪ Network Indicator LEDs
Green (LINK): Network connections. This LED lit.
Orange (A T): Data communications. This LED flashes.
Installation
1. Take out the IP camera from the box. onnect the network cable
to RJ-45 network port and connect power cable to D power input
jack of the IP camera (FIG.1). Then fix bracket to the wall (FIG.2).
English
- 2 -
2. Loosen the pan and tilt adjustment screws on the bracket to turn
the camera body to the desired angle and then tighten the screws
(FIG.3 & FIG.4).
Notes
1. The camera built-in the Micro SD card slot and the Reset Key.
Please refer to Product Overview. If want to use two functions as
above, first please take out the screw of front cover and rear cover
(FIG.5). Once it’s done for used , please tighten those screws
again (FIG.6).
2. While installing this camera, please curve output cable to be “U”
type for avoiding the water penetrates into the camera through
connected position of output cable and camera (FIG.7 & FIG.8).
English
- 3 -
3. To make sure camera’s safety and waterproof function, please use
the adhesive tape to wrap connected position of D power cable
and Network cable (FIG.9 & FIG.10).
System Architectures
For connecting HD IP cameras to the network, please follow one of
the system architectures:
(1). Use a D 12V power adapter and a network switch to connect to
the network.
English
- 4 -
(2). Use a PoE network switch to connect to the network.
(3). Use a PoE power injector and a network switch to connect to the
network.
Emergency Factory Default
To restore factory default settings by hardware, please follow these
steps:
1. Hold “RESET Key” for 10 seconds, then release.
2. After about 40 seconds, the network LED light should turn off,
and the back on again.
3. This camera has completed the factory default settings, and can
then reboot.
4. Search for the IP device using the IPScan software.
5. Start the IP device via Internet browser.
6. Enter the default username “admin” and password “pass” to
operate.
NOTE:
For user convenience, restoring the factory default settings
will revert to the default IP address 192.168.0.200.
English
- 5 -
Before Accessing IP Cameras
Before accessing the IP camera, make sure that the camera’s RJ-45
network, audio, and power cables are properly connected. To set the
IP address, consult your network administrator for an available IP
address. The default IP address for each IP camera is 192.168.0.200.
Users can use the default IP address for verifying the camera’s
network connection.
Software Requirements
Merit LILIN Universal ActiveX software components are required for
web interface display of JPEG or H.264 Full HD video. When you
login to the IP camera by Internet Explorer, the security warning
dialog box will prompt the installation of the LILIN Universal ActiveX.
lick Install to download it.
Configuring IP Addresses by IPScan Software
To configure an IP address using the IP scan tool, you can copy the
IPScan software from the installation D, and paste to your
computer. Alternatively, you can execute the IPScan software from
the installation D, or download the software from the Merit LILIN
website (www.meritlilin.com). To change the settings of the IP
address, subnet mask, gateway, or HTTP port, you can follow the
steps below:
English
- 6 -
1. Run the IPScan software.
2. lick Refresh. All available devices should be listed in the device
list.
3. Select your device from the list provided.
4. hange the IP address, subnet mask, gateway, or HTTP port for
the IP camera.
5. lick Apply to submit the settings.
6. lick Refresh to verify the settings.
Configuring IP Addresses via Web Interface
To change an IP address via web interface, type the default IP
address (192.168.0.200) in the Internet browser and follow the steps
below:
1. Login to the H.264 Full HD IP camera by the default username
“admin” and default password “pass”
2. lick Basic Mode configuration hyperlink.
3. lick Network->General hyperlink.
4. hange the IP address, subnet mask, gateway, or HTTP port for
the IP camera.
5. lick Sub it to verify the settings.
English
- 7 -
Internet Browser Settings & Application Required
Make sure your Internet browser allows the signed ActiveX plug-in
to work on your computer. Set “Download Signed ActiveX plug-in
controls” to “Prompt” and “Run ActiveX control and plug-in” to
“Enable”. You can set this option via Internet Explorer-> Tools->
Options-> Security Settings.
Once complete, you can access the IP camera’s live video by entering
the default IP address via your Internet browser. As the security
warning dialog box appears, click OK to download the ActiveX directly
from the IP camera.
English
- 8 -
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Lilin Telecamera di sicurezza
Lilin
Lilin PIH-2422 Manuale utente
Lilin
Lilin CMR6082X Manuale utente
Lilin
Lilin PIH-802 Manuale utente
Lilin
Lilin MR8322 Manuale utente
Lilin
Lilin PIH-0742XW Manuale utente
Lilin
Lilin 66-8322CSB-1B Manuale utente
Lilin
Lilin PIH - 7625 Manuale utente
Lilin
Lilin AHD DOME IR CAMERA Manuale utente
Lilin
Lilin Z2R8122X-P Manuale utente
Lilin
Lilin PIH-0746XW Manuale utente
Lilin
Lilin CMR70826 N/P Manuale utente
Lilin
Lilin iMegapro IPR7722ESX Manuale utente
Lilin
Lilin ZR8022EX10 Manuale utente
Lilin
Lilin CMG052X35 Manuale utente
Lilin
Lilin AHD705A3.6 Manuale utente
Lilin
Lilin SP2034 Series Manuale utente
Lilin
Lilin IPC0522 Manuale utente
Lilin
Lilin ST1358 series Manuale utente
Lilin
Lilin PIH - 7000 Manuale utente
Lilin
Lilin CMR6186X3.6 N/P Manuale utente
