Linear Technology DC1261A Guida rapida alla configurazione

dc1261af

DEMO MANUAL DC1261A

DESCRIPTION

LTM8022

36V, 1A Step-Down

µModule Regulator

Demonstration circuit 1261A features the LTM

8022 step-

down μModule

regulator delivering a 3.3V output from a

4.5V to 36V input supply. As a step-down converter, the

LTM8022 requires a minimumamount of headroomto keep

the output in regulation. The device may be synchronized

to an external clock or allowed to enter low ripple Burst

Mode

operation at light load conditions by applying the

appropriate signal to the SYNC pin. Current sharing with

another LTM8022 is enabled by tying the VIN, VOUT and

SHARE pins together to support higher output loads.

L, LT, LTC, LTM, μModule, Burst Mode, Linear Technology and the Linear logo are registered

trademarks of Linear Technology Corporation. All other trademarks are the property of their

respective owners.

PERFORMANCE SUMMARY

BOARD PHOTO

The LTM8022 data sheet must be read in conjunction with

demo manual prior to working on or modifying demo

circuit DC1261A.

Design files for this circuit board are available at

http://www.linear.com/demo

(TA= 25°C)

PARAMETER CONDITION VALUE

Input Voltage Range 4.5V to 36V

Output Voltage, VOUT 3.3V ±3%

Maximum Output Current 1A

Typical Switching Frequency 600kHz

Downloaded from Elcodis.com electronic components distributor

dc1261af

DEMO MANUAL DC1261A

QUICK START PROCEDURE

Demonstration circuit 1261A is an easy way to evaluate

the performance of the LTM8022. Refer to Figure 1 for

proper measurement equipment setup and follow the

procedure below:

Note: When measuring the input or output voltage ripple,

care must be taken to avoid a long ground lead on the

oscilloscope probe. Measure the input or output voltage

ripple by touching the probe tip directly across the VIN or

VOUT and GND terminals. See Figure 2 for proper scope

probe technique.

1. Place JP1 on the ON position.

2. With power off, preset the input supply within the op-

erating range of the LTM8022 then connect the input

power supply to VIN and GND.

3. Turn on the input power supply.

Note: Make sure that the input voltage does not exceed

the maximum input voltage.

4. Check for the proper output voltage.

Note: If there is no output, temporarily disconnect the

load to make sure that the load is not set too high.

5. Once the proper output voltage are established, adjust

the load within the operating range and observe the

output voltage regulation, ripple voltage, efficiency and

other parameters.

Downloaded from Elcodis.com electronic components distributor

dc1261af

DEMO MANUAL DC1261A

QUICK START PROCEDURE

–

–+

–

LOAD

V+

–

+–

–

Figure 1. Proper Measurement Equipment Setup

Figure 2. Measuring Input or Output Ripple

VIN GND

Downloaded from Elcodis.com electronic components distributor

dc1261af

DEMO MANUAL DC1261A

PARTS LIST

ITEM QTY REFERENCE DESCRIPTION MANUFACTURER/PART NUMBER

Required Circuit Components

1 1 C1 CAP, 1206 2.2μF 10% 50V X7R MURATA GCM31CR71H225KA55L

2 1 C2 CAP, 0805 22μF 10% 6.3V X5R TAIYO YUDEN JMK212BJ226KG-T

3 1 R1 RES, 0402 154k 1% 1/16W VISHAY CRCW0402154KFKEA

4 1 R2 RES, 0402 56.2k 1% 1/16W VISHAY CRCW040256K2FKED

5 1 U1 IC, MODULE LINEAR TECH. LTM8022EV

Additional Demo Board Circuit Components

1 1 CIN CAP, 22μF 20% 50V ALUM SANYO 50CE22BS

2 1 C3 CAP, 0603 0.1μF 10% 50V X7R TDK C1608X7R1H104K

3 2 R4, R3 RES, 0402 100k 1% 1/16W VISHAY CRCW0402100KFKED

4 1 R5 RES, 0402 10k 5% 1/16W VISHAY CRCW040210K0JNED

Hardware For Demo Board Only

1 5 E1, E2, E4, E5, E9 TURRET MILL-MAX 2501-2-00-80-00-00-07-0

2 4 E3, E6, E7, E8 TURRET MILL-MAX 2308-2-00-80-00-00-07-0

3 1 JP1 HEADER, 3-PIN, 2mm SAMTEC TMM-103-02-L-S

4 1 XJP1 SHUNT, 2mm SAMTEC 2SN-BK-G

5 4 STANDOFF, SNAP ON KEYSTONE_8831

Downloaded from Elcodis.com electronic components distributor

dc1261af

DEMO MANUAL DC1261A

Information furnished by Linear Technology Corporation is believed to be accurate and reliable.

However, no responsibility is assumed for its use. Linear Technology Corporation makes no representa-

tion that the interconnection of its circuits as described herein will not infringe on existing patent rights.

SCHEMATIC DIAGRAM

Downloaded from Elcodis.com electronic components distributor

dc1261af

DEMO MANUAL DC1261A

Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035-7417

(408) 432-1900 ●FAX: (408) 434-0507 ●www.linear.com

LT 0511 • PRINTED IN USA

DEMONSTRATION BOARD IMPORTANT NOTICE

Linear Technology Corporation (LTC) provides the enclosed product(s) under the following AS IS conditions:

This demonstration board (DEMO BOARD) kit being sold or provided by Linear Technology is intended for use for ENGINEERING DEVELOPMENT

OR EVALUATION PURPOSES ONLY and is not provided by LTC for commercial use. As such, the DEMO BOARD herein may not be complete

in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including but not limited to product safety

measures typically found in finished commercial goods. As a prototype, this product does not fall within the scope of the European Union

directive on electromagnetic compatibility and therefore may or may not meet the technical requirements of the directive, or other regulations.

If this evaluation kit does not meet the specifications recited in the DEMO BOARD manual the kit may be returned within 30 days from the date

of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY THE SELLER TO BUYER AND IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS

FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THIS INDEMNITY, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR

ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user releases LTC from all claims

arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all

appropriate precautions with regard to electrostatic discharge. Also be aware that the products herein may not be regulatory compliant or

agency certified (FCC, UL, CE, etc.).

No License is granted under any patent right or other intellectual property whatsoever. LTC assumes no liability for applications assistance,

customer product design, software performance, or infringement of patents or any other intellectual property rights of any kind.

LTC currently services a variety of customers for products around the world, and therefore this transaction is not exclusive.

Please read the DEMO BOARD manual prior to handling the product. Persons handling this product must have electronics training and

observe good laboratory practice standards. Common sense is encouraged.

This notice contains important safety information about temperatures and voltages. For further safety concerns, please contact a LTC applica-

tion engineer.

Mailing Address:

Linear Technology

1630 McCarthy Blvd.

Milpitas, CA 95035

Downloaded from Elcodis.com electronic components distributor

Indice

Altri manuali Linear Technology Scheda madre

Linear Technology

Linear Technology DC1705C Guida rapida alla configurazione

Linear Technology

Linear Technology DC708 Manuale utente

Linear Technology

Linear Technology DC1999A Guida rapida alla configurazione

Linear Technology

Linear Technology Linduino One Guida rapida alla configurazione

Linear Technology

Linear Technology DC1274A Guida rapida alla configurazione

Linear Technology

Linear Technology DC2222A Guida rapida alla configurazione

Linear Technology

Linear Technology DC1954A Guida rapida alla configurazione

Linear Technology

Linear Technology DC1339 Manuale utente

Linear Technology

Linear Technology LTC3526 Manuale utente

Linear Technology

Linear Technology DC1555A Guida rapida alla configurazione

Linear Technology

Linear Technology DC1959A Guida rapida alla configurazione

Linear Technology

Linear Technology DC1123 Manuale utente

Linear Technology

Linear Technology DC1962C Guida rapida alla configurazione

Linear Technology

Linear Technology DC1816B Manuale utente

Linear Technology

Linear Technology DC1812A Guida rapida alla configurazione

Linear Technology

Linear Technology DC890B Manuale utente

Linear Technology

Linear Technology DC1732 Series Guida rapida alla configurazione

Linear Technology

Linear Technology DC2358A Manuale utente

Linear Technology

Linear Technology Analog Devices DC2814A-A Guida rapida alla configurazione

Linear Technology

Linear Technology 968A-B Manuale utente

Linear Technology

Linear Technology DC1763A Guida rapida alla configurazione

Linear Technology

Linear Technology DC2143A-B Manuale utente

Linear Technology

Linear Technology DC1565A Guida rapida alla configurazione

Linear Technology

Linear Technology DC1789A Guida rapida alla configurazione

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente