Linn NEXUS Manuale utente

LINN NEXUS

OWNERS MANUAL

NTRODUCTION Thank you for choosing our Linn NEXUS LS250 Loudspeakers, the result of

extensive design and development work. The NEXUS set new standards of performance in

loudspeakers of this type.

Remember, no loudspeaker is capable of improving the quality of the input signal so the NEXUS should

be used with good quality ancillary equipment.

INSTALLATION When removing the loudspeakers from their boxes, lift the cabinets out by their sides.

This will avoid damage to the grilles and the drive units.

Please retain all packing for possible future transportation.

All loudspeakers perform best when rigidly mounted. To achieve this, Linn have designed a KU-STONE

stand for the NEXUS, which includes floor spikes. Use of these KU-STONE stands will give optimum

sound quality and ensure that the drive units are in the correct position relative to the listener.

STANDS

Connection of the loudspeakers to the amplifier should be made with a good quality cable. Linn K20

loudspeaker cable is ideal, the leads should be terminated with the connectors supplied to ensure

optimum performance. The use of other connectors will degrade the sound quality of your system.

The cable is marked with the Linn symbol to indicate directionality. The bare wires shown should be

connected to the amplifier and the end marked with the circular logo should be connected to the

loudspeakers.

< LOUDSPEAKERS AMPLIFIER >

Take care to ensure that the wiring is correct. The red socket is positive and the black is negative. The

positive wire (red connectors is identified by a rib along the side of the cable.

NEXUS speakers are designed to perform best when placed close to a wall. Ideally the rear of the

loudspeaker should be between 4" and 12" (10cm and 30cm) from the wall and at least 18" (45cm) from

any corner. .

NEXUS can also benefit from being angled inward slightly by 5 to 10 degrees.

These are general guidelines and a little experimentation with positioning will optimise results for a

particular room, your dealer will be pleased to do this when he installs your equipment.

CONNECTIONS

POSITIONING

The NEXUS grille is special because it mounts directly onto the front baffle of the speaker. This avoids

the problems of diffraction produced by conventional grille frames.

The grille can be removed by gripping the top right corner, pulling it so that the elastic clears the baffle

and then carefully removing the rest.

Fitting the grille is a time consuming procedure, so unless you want to use the speaker without the grille,

it is best to leave it on. If you have to refit the grille, first find the join in the elastic and locate this in the

slot above the port before fitting the top part of the grille.

GRILLE

Bi-wiring improves the performance of a loudspeaker. By using a separate cable for the bass and treble

section some interaction between the bass and treble section is removed. The extra cost of an

additional pair of loudspeaker cables is more than justified by the improvement in sound quality gained.

To convert the NEXUS to bi-wired mode, use the key provided to unscrew the negative (black) socket

caps and remove the link. Replace and tighten the caps and then repeat for the positive (red) sockets,

and firmly re-tighten.

Because most amplifiers have only one speaker output you will have to double up the connection to the

speaker plug - your dealer will be pleased to make up the necessary leads for you, and to set up your

loudspeakers.

For ultimate performance you can go one step beyond bi-wiring and use two amplifiers, one channel for

the bass and one channel for the treble. Your dealer will be pleased to effect this mode of operation for

you.

BI-WIRING

BI-AMPING

Linn loudspeakers require no internal maintenance and on no account should you try to remove any of

the drive units, which are carefully tightened and sealed at the factory.

For servicing, always return the speakers as a pair to your supplier, using the original packing in order to

reduce the risk of damage in transit.

If you have lost the packaging, your supplier can provide a replacement set.

Ensure your equipment is insured by you during transit, repair, and return shipping.

These units are guaranteed under the conditions that apply in the country of purchase. To help us,

please return your guarantee card.

In addition to any statutory rights the customer may have, we undertake to replace any parts that have

failed due to faulty manufacture if you register your purchase with us.

Please keep a copy of your sales receipt as this will establish the purchase date of the loudspeakers

and refer all enquiries through authorised dealers only.

LINN PRODUCTS LIMITED, FLOORS ROAD, WATERFOOT, EAGIESHAM,

GLASGOW G76 OEP, SCOTLAND. TELEPHONE: ++44 (0)141 307 7777

FACSIMILE ++44 (0)141 644 4262

MAINTENANCE/SERVICE

GUARANTEE

Indice

Altri manuali Linn Altoparlanti

Manuali Altoparlanti popolari di altre marche

argon audio

argon audio IE20 Manuale utente

Denon

Denon SC-N7 Manuale utente

Gemline

Gemline Ace 3952 Manuale utente

Focal

Focal ON WALL 300 Manuale di istruzioni

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuale utente

SoundLogic

SoundLogic BCCS-6/6395 Manuale utente

Peavey

Peavey DTH 218 Manuale utente

Avantree

Avantree Pluto Air Manuale utente

Morel

Morel Integra Series INTEGRA OVATION 4 Manuale utente

Oppo

Oppo SONICA Manuale utente

Bose

Bose SoundLink Wireless Music System Manuale utente

Rocksteady

Rocksteady Stadium Manuale utente

Bowers & Wilkins

Bowers & Wilkins 4 Manuale utente

Sonance

Sonance SONOS OUTDOOR Series Manuale utente

Electro-Voice

Electro-Voice EVID FM4.2 Manuale utente

Pioneer

Pioneer XW-HTD630 Manuale utente

Onn

Onn BWA16AA002 Manuale utente

HP GL313AA - USB Speakers PC Multimedia Manuale utente