LTB MNL300 Series Guida all'applicazione
D
De
ev
vi
ic
ce
e
M
Ma
an
nu
ua
al
l
N
Ni
it
tr
ro
og
ge
en
n
L
La
as
se
er
r
M
MN
NL
L3
30
00
0
September 2016, Rev. 3
LTB Lasertechnik Berlin GmbH •Am Studio 2c •D-12489 Berlin
Tel.: +49 (0)30 91 20 75-100 •Fax: +49 (0)30 91 20 75-199
E-mail: info@ltb-berlin.de •http://www.ltb-berlin.de
Operating Manual MNL 300 2
D
De
ea
ar
r
c
cu
us
st
to
om
me
er
rs
s
With the purchase of a laser from the MNL 300 series, you
have selected a state-of-the-art Nitrogen Laser.
The laser satisfies sophisticated needs and demanding
goals in various applications within the industrial area. The
following properties reveal the advantages of the MNL 300.
High pulse power
Minimal beam divergence
Minimal time jitter
Pulse halfwidths in the sub- and nanosecond range
Long lifetime
Low operating costs
These properties make the laser attractive for applications
where high quality, stable output and cost-effectiveness are
required.
The MNL is mainly used in
MALDI-TOF-Mass spectroscopy
Laser-induced fluorescence spectroscopy
Time-resolved spectroscopy
laser-induced plasma spectroscopy
Laser ablation
Micro-structuring
Cell dissection under the microscope
Laser acoustics
Calibration of fast sensors
Pump source of dye lasers
Amplification of ultra-short laser pulses
Technological processes like laser-induced bonding,
hardening and cleaning
Special applications in the environment and
biotechnology
The laser operates on the principle of transversal excitation.
A fast high-current discharge will be triggered by means of
a solid-state high-voltage switch thus generating laser
radiation.
Your laser has been carefully tested for all operating states
with LTB’s end test program and left the firm in a good
condition.
LTB wishes you much success in working with the laser on
your projects. If this operation manual does not answer all
your questions, please do not hesitate to contact us.
Content 3
CONTENTS
1
SAFETY PRECAUTIONS 5
1.1
I
NVISIBLE LASER RADIATION
5
1.2
H
IGH VOLTAGE UP TO
12
K
V 6
1.3
D
ANGEROUS GASES
6
1.4
S
YMBOLS
6
1.5
S
ERVICING AND
D
ISCLAIMER
7
1.5.1
R
ESONSIBILITIES OF THE BUYER
7
1.5.2
L
IABILITY
,
R
EPLACEMENT PARTS
7
1.5.3
D
ISCLAIMER OF
I
MPLIED
W
ARRANTY
7
1.6
C
LEANING INSTRUCTION
8
1.7
C
ONDITIONS
O
F ACCEPTABILITY
8
2
SYSTEM REQUIREMENTS 9
2.1
P
LACE AND WAY OF INSTALLATION
9
2.2
E
LECTRIC REQUIREMENTS
10
C
ONNECT THE LASER POWER SUPPLY UNIT ONLY TO A MAINS THAT CORRESPONDS TO THE VALUES STATED ON THE
TYPE LABEL
. 10
P
LEASE OBSERVE
:
ONLY A MAINS THAT PROVIDES AN EARTHED CONDUCTOR IS TO BE USED
. 10
2.3
L
ASER CONTROL
10
3
INSTALLATION 11
3.1
C
ONNECTIONS
11
3.2
A
CCLIMATIZING THE LASER
11
4
OPERATING THE LASER 12
4.1
E
STABLISH THE READINESS FOR OPERATION
12
4.2
R
EMOTE KEY AND REMOTE SOCKET
12
4.3
T
HE EXTERNAL REMOTE CIRCUIT
12
4.4
C
ONNECTING EXTERNAL APPLICATIONS
12
4.5
S
TARTING THE LASER OPERATION
13
4.6
S
WITCHING OFF THE LASER
13
4.7
P
ROTECTING THE LASER
13
5
SAFETY FUNCTIONS 14
5.1
C
ONFIGURATION OF REMOTE KEY CONNECTOR
14
6
OPTIONAL FEATURES 15
6.1
F
IBER COUPLING
15
6.2
E
LECTRICAL TRIGGERING
15
6.3
P
ULSE ENERGY MEASUREMENT
15
Content 4
7
APPENDIX 16
7.1
S
PECIFICATIONS
,
T
ECHNICAL
D
ATA
16
7.2
T
ABLE OF LABELS
18
7.3
I
NSPECTION AND MAINTENANCE
21
7.4
D
IMENSIONS AND INTERFACES
22
7.5
F
UNCTIONAL BLOCK DIAGRAM
23
7.6
S
AFETY FUNCTIONS
24
7.7 Syncout (optional feature)
25
Safety precautions 5
1 Safety precautions
MNL Lasers are 3B class lasers (IEC 60825-1).
Improper treatment and operation of the laser can cause
damage to your health.
Please follow carefully all the instructions in this manual.
1.1 Invisible laser radiation
The laser emits intensive invisible laser radiation in the UV
range.
Do not look into the laser beam! Direct eye contact
will cause serious damage and possible blindness.
Please always wear laser safety goggles appropriate to
the wavelength of 337.1 nm and ensure that all persons in
the vicinity of the laser also wear laser goggles during
laser operation.
For MNL lasers, you need class L6 laser goggles.
Please observe that there are no reflecting materials in the
beam path by which the laser beam could unintentionally
be directed towards persons or sensitive materials.
Always use beam shutters made of non-inflammable
materials in your set-up.
Always follow the safety regulations.
Safety precautions 6
1.2 High voltage up to 12 kV
A high voltage of up to 12kV is generated in the laser.
Therefore, observe the protected earth connection of the
mains. The earth conductor connection from the laser
housing to the input of the LTB power supply of the laser
is ensured.
Do not open the laser due to occurring dangerous
high voltages in the interior of the laser!
Because of high voltage circuits, the laser should never be
opened nor should any objects be put into the laser casing
openings.
1.3 Dangerous gases
The high-energetic UV radiation causes ozone. No
noxious gases are used in the laser. The cartridge has a
pressure-safe sealing.
Please observe that the laser operating room is
sufficiently ventilated.
1.4 Symbols
Danger of hazardous invisible laser
radiation.
Danger of hazardous high voltage.
Important operating instructions. Please
read the manual first.
Safety precautions 7
1.5 Servicing and Disclaimer
The laser must be used properly. LTB is not liable for
improper use.
Opening of the laser is prohibited. If warranty or general
repair or service to a LTB product is requested by the
customer involving the product’s return to LTB.
1.5.1 Resonsibilities of the buyer
The buyer is responsible for providing the appropriate
utilities and a operating enviroment as outlined in the
product literatur.
Damage to the laser system caused by failure of buyer´s
utilities or failure to maintain an appropriate operating
environment, is solely the responibiliety of the buyer and is
specifically excluded from any warranty, warranty
extension, or services ageement.
1.5.2 Liability, Replacement parts
Any modification of the laser, replacement of components
or adjustment of the laser must be done by authorized
service staff.
Only components tested by LTB must be used.
Any liability and warranty lapses with the opening of the
laser or any modification without LTB’s explicit written
consent.
Damages caused by the disregard of this user manual are
not subject to warranty. LTB will not accept liability for any
resulting defects or problems.
1.5.3 Disclaimer of Implied Warranty
The foregoing is in lieu of all other warranties Expressed
or Implied, and there are no warranties of merchantability
or fitness or any other remedies available other than as
expressed herein.
Safety precautions 8
1.6 Cleaning instruction
For cleaning, turn off the laser and disconnect from mains!
Do not use cleaning supplies. Use a slightly moist or dry
cloth to clean the enclosure, be careful with the link.
The laser can be put back into operation after drying.
1.7 Conditions Of acceptability
The user is responsible to verify the requirement of the
standard IEC60825-1:2007 and has to provide information
about NOHD (Nominal Ocular Hazard Distance)and MPE
in his own devise documentation.
System requirements 9
2 System requirements
2.1 Place and way of installation
The laser has to be operated and stored in a dry, dust-
poor and well-ventilated area.
Operation temperature
°C +15 ... +38
Storage temperature °C -10 ... +60
Max. rel. humidity % 85
Air pressure mbar 750 ... 1300
Please make sure that the laser is not placed close to any
heat sources.
Moreover observe that the air inlet is on the side of the
beam output of the laser and must not be blocked. We
advice to replace the air inlet filters of the laser every 6 to
18 months depending on the dust concentration of the
cooling air.
The air outlet openings on both sides of the laser cover
must stay free. Minimum spacing to cabinet walls perpen-
dicular to airflow is 80 mm.
No spacing reqirements for other surfaces.
Mounting the laser may only be realized via the base plate
with the red-marked threaded holes.
(See Dimensions and interfaces, appendix 7.4)
The laser may be used in a standing position or hanging
with the beam output downwards. Other positions can be
checked on request.
System requirements 10
Please observe: only a mains that provides an
earthed conductor is to be used.
Connect the laser power supply unit only to a mains
that corresponds to the values stated on the type
label.
2.2 Electric requirements
The laser is supplied with a low voltage of 24 V DC 3.0 A.
A power supply unit providing the low voltage from the
mains is optional part of the delivery.
The mains connection values are:
100 to 240 V, 47/63 Hz, 1.1-0.45 A (see type label).
The laser power supply unit has an earthed conductor
connection that is connected to the laser housing via the
connection cable. The low voltage is off-earth, the minus
line is connected to the frame ground.
Using another power supply requires the written consent
of LTB Lasertechnik Berlin.
2.3 Laser control
The lasers of the MNL 300 series operate without
computer. The laser has to be triggered. The trigger input
is anly optical (HP OWG). Electrical triggering is possible
with optional converter (6.2)
Since there is no beam shutter that fulfills the safety
requirements of system redundancy, the customer has to
sign an OEM agreement. The user has a higher
responsibility for the compliance with laser safety. The
regulations of the IEC 60825-1 (laser safety) are to be
observed.
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali LTB Strumento di misura
