Lutron Electronics Energi Savr Node Manuale utente

Getting Started

Step 1: Wire connections

1.1 Connect one end of the supplied Ethernet cable to an

EcoSystem®Energi Savr Node unit (QSN-1ECO-S,

QSN-2ECO-S) or to an Energi Savr Node Ethernet

Programming Interface (QSE-CI-AP-D).

NOTE: If more than one QS link is present, these steps

will need to be repeated for each QS link.

1.2 Connect the other end of the supplied Ethernet cable to

one of the standard LAN ports on the wireless router. Do

not plug the cable into the WAN (Internet) port.

1.3 Connect the supplied router power supply to the router

and plug the power supply into a wall outlet. Verify that the

wireless router is powered on by conﬁrming that the lights

on the front of the unit are on.

Overview

The Energi Savr Node Wireless Setup Kit (C-ESN-SETUP) contains the following items:

 • Apple iPod touch device preloaded with Lutron®Energi Savr Node setup application (also available

on the Apple App Store)

 • WallchargerforiPod touch

 • 802.11gwirelessrouterpreconguredtocommunicatewithbothiPod touch device and Lutron

Energi Savr Node units

 • EthernetcableforconnectingwirelessroutertoEnergi Savr Node system

System Example

Energi Savr Node™Wireless Setup Kit

Quick-Start Guide

NOTE: The wireless router has already been conﬁgured

to communicate with the Apple iPod touch device. If

you restore the router to its factory default, you will

need to re-establish wireless communications between

the Apple iPod touch device and the router using the

Apple iPod touch device’s WiFi connection screen.

Step 2: Discover the system

2.1 Remove the Apple iPod touch device from the packaging

and power on the device by holding the button on the top

of the unit for several seconds (until the screen becomes

active). Allow some time for the device to boot up.

NOTE: You may ﬁnd that the Apple iPod touch device

is not fully charged. If necessary, connect the supplied

Apple iPod touch device wall charger

to a power source and then plug the

Apple iPod touch device into the

wall charger.

Wire type and corresponding maximum wire distance:

Type 1 Lutron GRX-CBL-346S cable: 500 ft (152 m)

Lutron GRX-CBL-46L cable: 2000 ft (610 m)

Type 2 Standard CAT5/CAT5E cable: 300 ft (91 m).

100 ft (30 m) cable included with kit.

NOTE: Total wire length not to exceed maximum wire distance shown above.

Wire Type 1

Apple iPod

touch

Wire Type 1

QS Link

QSM

Energi Savr Node

Unit

Wire Type 2

EcoSystem®

Energi Savr Node

(QSN-2ECO-S,

QSN-1ECO-S) or

ESN Programming

Interface

(QSE-CI-AP-D)

Wireless

Router

To Power

Outlet

Technical and Sales Assistance

If you need assistance, call the toll-free Lutron Technical Support Center.

Please provide the programming kit model number when calling: C-ESN-SETUP.

U.S.A. / Canada / Caribbean: 1.800.523.9466

Mexico: +1.888.235.2910

Other Countries: +1.610.282.3800

Visit our web site at www.lutron.com

Lutron Electronics Co., Inc | 7200 Suter Road | Coopersburg, PA 18036-1299 USA 032-344a11/10

2.2 Verify that the Apple iPod touch device has connected to

the wireless router. You should see wireless signal strength

indicator bars in the top-left corner of the Apple iPod touch

device main screen (see Figure 1 below).

NOTE: This connection may take some time to be

established. You should not proceed until the indicator

bars appear (see Figure 1 below).

2.3 Run the Energi Savr Node (ESN) setup application by

touching the icon (see Figure 1 below).

2.4 When the application loads, you should see the connected

Energi Savr Node unit.

Step 3: Set up the system

NOTE: Only follow these instructions when setting up

a system for the ﬁrst time. For a system that is already

operational and needs minor adjustments, Ballast

Addressing is NOT generally required; simply navigate

to existing areas and modify the settings as needed.

3.1 Connect to the device (for help during any part of the

set-up process, use the on-screen help button as shown in

Figure 2 below)

 •SelectthedesiredEnergi Savr Node unit and connect to it.

 •Whenprompted,enterapassword.Youwillneed

this password when connecting to the device to make

conﬁguration changes in the future.

3.2 Navigate to the conﬁguration screen

 •FromtheHome screen, navigate to System setup >

Conﬁgure an ESN. Select the desired ESN and touch

Next to see the main conﬁguration screen.

3.3 Verify wiring

 •NavigatetotheVerify wiring screen and ensure that all

ballasts/outputsarerespondingcorrectlytothesystem

commands.

3.4 Address ballasts

 •IfprogramminganEcoSystem®Energi Savr Node unit

(QSN-2ECO-S, QSN-1ECO-S), address the ballasts by

navigating to the Address ballasts screen.

3.5 Create areas

 •UsingtheSetup areas screen, create new areas that

correspond to the areas that you want to control in

your space (e.g. hallway, ofﬁce).

3.6 Deﬁne areas

 •WithintheSetup areas screen, perform the following

steps for each area that you created.

— Navigate to the Deﬁne lights in this area screen

and identify which lights belong to each area.

— If programming an EcoSystem Energi Savr Node unit

(QSN-2ECO-S, QSN-1ECO-S), navigate to the

Setup zones/scenes screen to deﬁne the lighting

zones that should exist in each area and assign the

appropriate lights from the area to each zone as

desired. Other Energi Savr Node models (such as

QSN-4S16-SandQSN-4T16-S)havezonesthatare

already pre-deﬁned.

— Also on the Setup zones/scenes screen, conﬁgure

the desired area scenes by modifying the scene

names as desired and specifying the zone light levels

for each scene.

— If desired, navigate to the Setup daylighting screen

and program the daylighting behavior by assigning

daylight sensors to each area, deﬁning the daylight rows

in each area, and calibrating the daylighting settings.

— If desired, navigate to the Setup occupancy screen

and program the occupancy behavior by assigning

occupancy sensors to each area and specifying the

occupied and unoccupied scenes.

3.7 Program controls

 •ReturntotheHome screen. Navigate to System setup

to view the various device programming options.

 •ProgramanyIRsensors,QSkeypads,GrakEye®QS

units, or other QS devices to control the Energi Savr

Node unit lighting as desired using the Program devices

and Program IR sensors screens.

3.8 Program dry contact inputs

 •ProgramanycongurabledrycontactinputsontheEnergi

Savr Node units using the Program ESN inputs screen.

Step 4: Start Saving Energy with your

Energi Savr Node System!

Lutron, EcoSystem and the sunburst logo are registered trademarks and Energi Savr Node is a trademark of Lutron Electronics Co., Inc.

Apple and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.

Figure 2. On-Screen Help Button of Energi Savr Node

Setup Application

On-Screen

Help Button

Energi Savr Node

setup application

icon

Wireless signal strengh indicator bars

Figure 1. Main Screen of iPod touch device

Indice

Altri manuali Lutron Electronics Unità di controllo

Lutron Electronics

Lutron Electronics QSGRK-6D Manuale del proprietario

Lutron Electronics

Lutron Electronics Maestro Wireless Pico Series Manuale utente

Lutron Electronics

Lutron Electronics GRAFIK Eye Architrave GRX-4SLB-DW Manuale utente

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-3P Istruzioni operative

Lutron Electronics

Lutron Electronics seeTouch guestroom solutions Manuale utente

Lutron Electronics

Lutron Electronics QSE-IO Manuale utente

Lutron Electronics

Lutron Electronics QS Timeclock Manuale del proprietario

Lutron Electronics

Lutron Electronics Vive PowPak Manuale utente

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Manuale utente

Lutron Electronics

Lutron Electronics QSGRK-3PCE Manuale del proprietario

Lutron Electronics

Lutron Electronics LQR-WPM-6D Istruzioni operative

Lutron Electronics

Lutron Electronics PowPak Energi TriPak Series Manuale utente

Lutron Electronics

Lutron Electronics Vive Series Manuale utente

Lutron Electronics

Lutron Electronics RadioRA RA-SBT-CHR Istruzioni operative e di sicurezza

Lutron Electronics

Lutron Electronics GRAFIK 6000 Manuale utente

Lutron Electronics

Lutron Electronics PowPak RMJS-16R-DV-B Manuale utente

Lutron Electronics

Lutron Electronics PowPak RMJ-5R-DV-B Manuale utente

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Istruzioni per il montaggio

Lutron Electronics

Lutron Electronics LMM-16R-DV-B Manuale utente

Lutron Electronics

Lutron Electronics GRAFIK Eye QS Manuale del proprietario

Lutron Electronics

Lutron Electronics Stanza SZ-2B Manuale utente

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-3P Istruzioni operative

Lutron Electronics

Lutron Electronics GRAFIK Eye QS with EcoSystem Istruzioni operative

Lutron Electronics

Lutron Electronics AuroRA ARMC-5T Manuale per l'uso e la cura

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente