Lutron Electronics SeeTouch guestroom solutions Manuale utente

seeTouch®guestroom solutions

Installation Guide Please Read

IMPORTANT:

•Lightingcontrolsmustbeinstalledbyaqualifiedelectricianinaccordancewithallapplicableregulations.

WARNING: Shock Hazard. Mayresultindeathorseriousinjury. DONOTWIRELIVE!Interrupt

powerviacircuitbreakerbeforewiringandservicing.

•Alwaysturnoffcircuitbreaker/MCBorremovemainfusefrompowerlinebeforedoinganywork.

•Toreducetheriskofoverheatingandpossibledamagetootherequipment,themodulemustbemounted

asshown.Failuretoprovideadequatespaceforcoolingmayresultinoverheatingandvoidthewarranty.

•Modulehumsslightlyduringoperationandtheinternalrelayclickswhenthecircuitisturnedonandoff.

Chooseaninstallationlocationwherethesesoundsareacceptable.

•Lightingcontrolsaredesignedforcommercialindooruseonly.

•ThiscontrolusesPELVwiringmethods.Checkwithyourlocalelectricalinspectorforcompliancewith

nationalandlocalcodesandwiringpractices.

230 V 50/60 Hz 8,75 A (40 – 350 W per zone)

24 V 200 mA (Panels with a power supply only)

2 seeTouch®guestroom solutions

seeTouch®guestroom solutions 3

Table of Contents

Overview

Panel Details

Poweredbyaprecision-engineereddimmingpanel,thenewseeTouch®guestroomsolutionisacost-effective,

simple-to-installlightingcontrolsolutionforhotelguestrooms.

Description

• Allowssetupoflightingscenesandshadepresetsusingbuttonsonthepanel.

• Controlsmanylightsourcetypesdirectlyandothersusingpowerinterfaces.

• Providesindividualcontroloflightsources.

• Includesbuilt-inastronomictimeclock.

• Includesonecontactclosureinputand24V powerforoccupantsensorsorotherbuildingmanagement

systems.

• Includescommunicationlinkforseamlessintegrationoflights,motorizedwindowtreatments,andcontrolstations.

• CompatiblewithallLutron®QSsystemcomponents.

Contents

Overview 3

Dimensions and Mounting 4

Panel Wiring 5

Control Unit Wiring 6

Wallstation Installation 7

Start-Up Procedure 8

Ethernet Wiring 9

Contact Closure Wiring 10

Warranty 11

Contact Information 12

4 seeTouch®guestroom solutions

Dimensions

Mounting

Attention Contractor!

Pleaseuseprovidedknockoutsfor

inputmainswiringconduit.Drilling

additionalholesinenclosurecould

damageelectroniccomponents

insidethepanel.

Alldimensionsinmm(in)

Notes

• Forindooruseonly.

• Consultdimensionsdrawingabove

forpanelsize,conduitknockouts,and

mountingholes.

• Mountwhereambienttemperatureis

0to40°C(32to104°F).

• Reinforcewallstructureforweightand

localcodesasnecessary.

• Mountpanelsoline/mainsvoltage

wiringisatleast1,8m(6ft)fromsound

orelectronicequipmentandwiring.

• Lutronrecommendsusing6mm

(0,25in)mountingbolts.

• Allow32mm(1,25in)clearanceon

eachsideofpanelforcover.

• Allow63mm(2,5in)between

enclosures.

• Panelweight:8kg(18lbs)

• Panelshouldnotbemountedinside

anotherelectricalencloser.

Top View

22 (0,88)

337 (13,25)

286 (11,25)

(3,14)

86 (3,39)

with cover

(2,93)

8 (0,31)

337 (13,25)

(1,0)

235

(9,25)

235

(9,25)

191

(7,5)

Front ViewLeft Side

View

Right Side

View

Bottom View

= Knockouts

= Do Not Use

These Knockouts

Front View

Mains

Wiring

No PELV

PELV

Wiring Only

Side

View

seeTouch®guestroom solutions 5

Panel Wiring Instructions

WARNING: Shock Hazard. Turn power OFF to all circuits before installing any part of the

dimming system. Wiring with the power on can result in death or serious personal injury.

NOTICE: Verify that the panel is fed from the correct voltage. A feed miswire or loss of a feed

neutral can cause damage to the equipment.

1.Pull dedicated feeds.Eachpanelrequiresa10Adedicatedfeed.

2.Power and control wires must be run in separate conduit or raceways.Runindividualneutralsforinput

andeachloadcircuit.

3.Use 10 A breakers. Do not exceed 2,1 kW per 10 A circuit. (350 W by 6 zones for 2,1 kW max)

4.Connect load wires to terminals DL1-DL6. Connect all load neutrals for each panel to the neutral

terminals (N).

Load Types

 Thepanelcancontrolincandescent,halogen(tungsten),magneticlow-voltage,andneon/coldcathodeload

types.Electroniclow-voltageandfluorescentloadtypescanbecontrolledwithanappropriateinterface.

• Notallzonesneedtobeconnected;however,connectedzonesmusthavealoadofatleast40W.

• Nozonemaybeloadedwithmorethan350W.Maximumloadcapacityforeachpanelis2,1kW.

• Panelmustnotcarrymorethan8,75Aoftotallightingload.

• AllElectronicLow-Voltage(ELV)lightingusedwiththeElectronicLow-VoltageInterfacemustberatedfor

reverse phase control dimming.BeforeinstallinganELVlightsource,verifywiththemanufacturerthattheir

transformercanbedimmed.Whendimming,anElectronicLow-VoltageInterfaceMUSTbeusedwiththepanel.

Wiring Note

 UsethebottomrightknockoutswhenpullingPELVwiresintothemainpanel,allotherknockoutsfor

non-PELVuse.

1.Strip25mm(1in)ofinsulationfromthePELVcable.

2.Strip9mm(3/8in)ofinsulationfromeachwire.

3.ConnectthePELVwirestothePELVterminalblock.Makesurenobarewireisexposedaftermaking

connections.

4.Therecommendedinstallationtorqueis0,4N•m(3,5in-lb)forPELVconnections.

(L) 220-240 V

( ) Ground / Earth

Occ Sensors

OCC SIG

24 V

OCC COM

Load

MUX

+24 V

COM

(N) Neutral

6 seeTouch®guestroom solutions

Control Unit Wiring

PELV System Wiring

• SystemcommunicationusesPELVwiring.

• Wiringcanbedaisy-chainedorT-tapped.

• Wiringmustberunseparatelyfromline/mainsvoltage.

• PELVwiringlinkrequires:

 –Two1,0mm2(18AWG)conductorsforcontrolpower.

 –Onetwisted,shieldedpairof0,5mm2(22AWG)fordatalink.

 –AvailablefromLutron,P/NGRX-CBL-346S;checkcompatibilityinyourarea.

• Totallengthofcontrollinkmustnotexceed610m(2000ft).

• Upto10wallstationscanbepoweredfromeachPanelwithapowersupply(seemodeldescriptionsfordetails).

1234

Panel #1

Non-RF Panel

(with power supply)

Panels with power supplies can power up to 10 wallstations and cannot

have terminal #2 tied to other panels with power supplies. As shown

in diagram.

* Pin 2 from Panel #2 powers wallstation but does not go to other panels.

Panel #2*

Non-RF Panel

(with power supply)

Panel #3

RF Panel

(NO power supply)

Panel #4

Non-RF Panel

(with power supply)

1234

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

Panel Wiring Example

Daisy-Chain Wiring Example

Panel

T-Tap Wiring Example

Panel

seeTouch®guestroom solutions 7

Wallstation Wiring: Panel with up to Ten Wallstation Controls

 EachpanelwithapowersupplycanpoweruptotenWallstationControls.Ifyouneedtopowermorethanten

WallstationControlsfromonepanel,installanexternal24V powersupply.

 Maximumof300m(1000ft)betweentheControlUnitandthesecondWallstation.Forlongerdistances,use

anexternalPELVrated24V powersupply.

IMPORTANT WIRING NOTE:

 Daisy-chaintheterminal1,terminal2,terminal3,andterminal4connectionstothepaneland

WallstationControls.

Note:DonotallowPELVwirestocontactline/mainswires.

Wallstation Installation

Control Station Device (CSD) Link Wiring

• Uselow-voltagePELVwiringtoconnectWallstations

tothepanellink.

• Makeconnectionsinsidethewallboxorinaswitch/

junctionboxwithamaximumwirelengthof2,5m

(8ft)fromthelinktotheWallstation.

• Strip9mm(3/8in)insulationfrombothtwistedpairs

inthewallbox.

• Two1,0mm2(18AWG)conductorsforcommon

(terminal1)and24V (terminal2).Thesewillnotfit

interminals.Connectasshown.

• Oneshielded,twistedpair0,5mm2(22AWG)for

datalink(terminals3and4).

• ConnectDrain/Shieldasshown.Donotconnect

toGround(Earth)orWallstation.Connectthebare

drainwiresandcutofftheoutsideshield.

Note: SomeWallstationshavea“D”terminalfor

Drain.TheDrain/Shieldwiremaybeconnectedto

thisterminal.

4 3 2 1

C B A

PELV(Class2:USA)

Controlwiring

(2)1,0mm2(18AWG)

1:Common

2:24V

(2)1,0mm2

(18AWG)

(2)1,0mm2

(18AWG)

DataLink-(1)twisted,shieldedpair

0,5mm2(22AWG)

3:MUX

4:MUX

RearofWallstation

Contact Closure Input Wiring

• UsePELV/SELVwiringtoconnectthecontact

closureinputstotheWallstation.

• Inputsmustbedrycontactclosureorground

referencedsolid-stateoutputs.

• Wallstationismiswireprotectedupto36V.

• Outputsmuststayintheclosedoropenstatesfor

atleast40msinordertoberecognizedbythe

Wallstation.

4 3 2 1

C B A

B:Input2

A:Input1

C:Common

(3)1,0mm2

(18AWG)

RearofWallstation

8 seeTouch®guestroom solutions

Wallstation Installation (continued)

1.Mountwallboxwithappropriatedepth.

2.Strip9mm(3/8in)insulationfrombothtwisted

pairsinthewallbox.

Start-up Procedure

Check Load Circuits

1.Makesurethefactory-installedbypassjumper(s)arestillinplacebetweentheL(Live)andDL(DimmerLoad)

terminals.Replacepanelcover.Turncircuitbreakeron.

2.ChecktheinputcurrenttotheL(Live)terminalwitha“clamp-on”typecurrentprobe.Thecurrentprobe

shouldmeasurenomorethan8,75A.

3.TurnloadsONforatleasttenminutes.Ifcircuitbreakertrips,turnpowerOFF,thenlocateandcorrectmiswire

oroverload.

Check Panel

1.WithpowerOFF,makesureallcontrolwiringiscorrect.Replacepanelcover.Turncircuitbreakeron.

2.Pushbuttonsonwallstationcontrol.Thelightingshouldgotofull,butthecontrolindicatorlightsshouldgo

on/off.

Remove Bypass Jumpers

1.TurnpowerOFF.

2.Removetheloadcircuitbypassjumperfromthecontrolpanel.

3.TurnpowerON.ChangethescenebuttonsontheGrafikEye®QStomakesuretheyadjustthelightlevel.

seeTouch®guestroom solutions 9

RS232/Ethernet Wiring

WARNING: Shock Hazard. Mayresultin

deathorseriousinjury. DONOTWIRELIVE!

Interruptpowerviacircuitbreakerbefore

wiringandservicing.

ForEthernetlink,useCAT5cable(notincluded)to

connecttoauxiliaryequipment.Maximumlength

forCAT5cableis100m(328ft).TheEthernet

LinkLEDwilllightcontinuouslywhenthelinkis

presentandwillflashwhenthereislinkactivity.

AdditionalEthernetnetworkequipmentandcables

notprovided.

Network Connections

DIP

Switches LED1:Power

LED2,3:Unused

LED4:RS232LinkTx

LED5:RS232LinkRx

LED6:DataLinkTx

LED7:DataLinkRx

DataLink

(tocontrol

units,

processors,

and

wallstations)

RS232

Link

Ethernet

Link

Ethernet Interface Wiring

RS232 Link Wiring

• Standard9-pinserialconnectorplugsintoRS232

equipment,andtoEthernetInterface.

• Mustbe15m(50ft)orless.

Ethernet Link Wiring

•StandardCAT5cableconnectsEthernetInterface

toPC,router,orotherEthernetsource.

•Nocrossovercableneeded.

•Shouldnotexceed100m(328ft).

•Ethernetnetworkandcablenotprovided.

RS232 Signals

Signals Pinon9-pinCable

Com 5

TxD 3

RxD 2

10 seeTouch®guestroom solutions

Contact Closure Wiring

IO Connections

DIP switches

LED 1: CCO 1

LED 2: CCO 2

LED 3: CCO 3

LED 4: CCO 4

LED 5: CCO 5

LED 6: Unused

LED 7: Status

Notes: CCO LED is ON when CCO NO (normally

open contact) is closed.

Status LED blinks once per second

during normal operation

CCO and CCI connectors hold one

0,08 - 1,5 mm2(28 - 16 AWG) wire

NC = Normally closed

NO = Normally open

Data Link (to wallstations)

3: MUX

1: Common

4: MUX

CCO 1 NC

CCO 1 NO

1-2 COM

CCO 2 NC

CCO 2 NO

CCO 3 NC

CCO 3 NO

3-4 COM

CCO 4 NC

CCO 4 NO

CCO 5 NC

CCO 5 NO

5 COM

CCI 1

CCI 2

CCI 3

CCI 4

CCI 5

COM

Contact Closure Outputs Contact

Closure

Inputs

1234567

Program button

2: 24 V

DIP switches

LED 1: CCO 1

LED 2: CCO 2

LED 3: CCO 3

LED 4: CCO 4

LED 5: CCO 5

LED 6: Unused

LED 7: Status

Notes: CCO LED is ON when CCO NO (normally

open contact) is closed.

Status LED blinks once per second

during normal operation

CCO and CCI connectors hold one

0,08 - 1,5 mm2(28 - 16 AWG) wire

NC = Normally closed

NO = Normally open

Data Link (to wallstations)

3: MUX

1: Common

4: MUX

CCO 1 NC

CCO 1 NO

1-2 COM

CCO 2 NC

CCO 2 NO

CCO 3 NC

CCO 3 NO

3-4 COM

CCO 4 NC

CCO 4 NO

CCO 5 NC

CCO 5 NO

5 COM

CCI 1

CCI 2

CCI 3

CCI 4

CCI 5

COM

Contact Closure Outputs Contact

Closure

Inputs

1234567

Program button

2: 24 V

Contact Closure Ratings

Five Input Terminals

• Acceptsmaintainedinputsandmomentaryinputswith40ms

minimumpulsetimes.

• Off-stateleakagecurrentmustbelessthan100μA.

• Opencircuitvoltage:24V maximum.

• Inputsmustbedrycontactclosure,solidstate,opencollector,

oractive-low(NPN)/activehigh(PNP)output.

 –OpencollectorNPNoractive-lowon-statevoltagemustbe

lessthan2Vandsink3,0mA.

 –OpencollectorPNPoractive-highon-statevoltagemustbe

greaterthan12Vandsource3,0mA.

• Lutronrecommendsamaximumof3occupantsensorswired

inparallelperinput.

Five Output Terminals

• Provideselectablemaintainedormomentary(250ms)outputs.

• Theinterfaceisnotratedtocontrolunclamped,inductiveloads.

Inductiveloadsinclude,butarenotlimitedto,relays,solenoids,

andmotors.Tocontrolthesetypesofequipment,aflyback

diodemustbeused(DCvoltagesonly).Seediagrambelow.

• Outputrelaysarenon-latching(i.e.ifrelaysareclosedand

powerislost,relayswillopen).

Supply

Voltage

0–24V

Resistive

Load

1,0A

0,5A

24V 

max.

Inductive

Load

Flyback

Diode

(requiredfor

inductive

loads)

IO

Output

Output Ratings

NO NC

COM

Indice

Altri manuali Lutron Electronics Unità di controllo

Lutron Electronics

Lutron Electronics Vive Series Manuale utente

Lutron Electronics

Lutron Electronics PowPak Energi TriPak Series Manuale utente

Lutron Electronics

Lutron Electronics PowPak RMJS-CCO1-24-B Manuale utente

Lutron Electronics

Lutron Electronics LQR-WPM-6D Istruzioni operative

Lutron Electronics

Lutron Electronics LCP128 Manuale operativo

Lutron Electronics

Lutron Electronics LMM-16R-DV-B Manuale utente

Lutron Electronics

Lutron Electronics QSN-2DALUNV-S Manuale utente

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Manuale utente

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-3P Istruzioni operative

Lutron Electronics

Lutron Electronics GRAFIK 6000 Manuale utente

Lutron Electronics

Lutron Electronics QSGRK-3PCE Manuale del proprietario

Lutron Electronics

Lutron Electronics Vive DFCSJ-OEM-OCC Manuale utente

Lutron Electronics

Lutron Electronics PowPak RMJ-CCO1-24-B Manuale utente

Lutron Electronics

Lutron Electronics QS Timeclock Istruzioni operative

Lutron Electronics

Lutron Electronics QSE-IO Manuale utente

Lutron Electronics

Lutron Electronics QS Timeclock Manuale del proprietario

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Manuale utente

Lutron Electronics

Lutron Electronics PowPak RMK-CCO1-24-B Manuale utente

Lutron Electronics

Lutron Electronics Vive PowPak Manuale utente

Lutron Electronics

Lutron Electronics PowPak RMJS-16R-DV-B Manuale utente

Lutron Electronics

Lutron Electronics GRAFIK Eye QS Manuale del proprietario

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Manuale utente

Lutron Electronics

Lutron Electronics RadioRA RA-SBT-CHR Istruzioni operative e di sicurezza

Lutron Electronics

Lutron Electronics Energi Savr Node Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente

Lutron Electronics seeTouch guestroom solutions Manuale utente

Manuali Unità di controllo popolari di altre marche