Matchmaster 12MM-DSTM2 Manuale utente

For technical support call 1800 237 425 or visit www.matchmaster.com.au | Page 1 of 16

Instruction Manual

12MM-DSTM2

SAFETY

WARNING

CONTENTS

Safety

Warning

Note

1 Overview

1.1 Features

1.2 Accessories

2 Introduction of panel function

2.1 Remote Control

2.2 Front panel introduction

2.3 Top panel introduction

2.4 Rear panel introduction

3 Detail operation guide

3.1 DVB-S/S2 Satellite

3.1.1 Satellite Finding

3.1.2 Dish Setup

3.1.3 Angle Calculation

3.1.4 Constellation Analyzer

3.2 DVB-T/T2 Terrestrial

3.3 DVB-C Cable

3.4 Compass

3.5 Spectrum Analyzer

3.6 Multimedia

3.7 Setting

3.7.1 Program

3.7.2 EPG

3.7.3 Device Setup

3.7.4 System

3.7.5 Picture

3.7.6 Option

3.7.7 Time

3.7.8 USB Upgrade

4 Technical Speciﬁcations

1. Please read this manual carefully before rst use.

2. The LCD is not a touch screen.

3. Do not place heavy items on the device.

4. Do not leave the device near to heat sources, in direct sunlight, in places with strong mechanical vibration or dusty

environments.

5. Please place the device in ventilated surroundings.

6. The device should be fully charged before using for the rst time (recommend 6 hours for the rst charge).

7. Contact Matchmaster Communications Pty Ltd if malfunction of the device happens.

8. Damaging the device on operation without following the guideline will not be warranted.

1. Avoid using batteries near heat sources.

2. Do not get wet.

3. Avoid charging in heated locations or direct sunlight.

4. Charge using only charging accessories supplied.

5. When the battery is being charged by a vehicle charger, please ensure the polarity of the charging connection is

correct.

For technical support call 1800 237 425 or visit www.matchmaster.com.au | Page 2 of 16

Instruction Manual

12MM-DSTM2

The 12MM-DSTM2 is an HD digital signal meter and portable device for installation and adjustment of satellite and

terrestrial receiving antennas.

1.1 Features

• Combination of DVB-T/T2/C and DVB-S/S2

• High resolution 5’’TFT LCD

• Multi-lingual OSD and use-friendly UI

• Supports Spectrum function

• Real time constellation display

• Supports TP search and blind search

• USB 2.0 for software update/media play back

• Supports time shift

• Supports TP PVR

• Supports program edit (move/skip/lock/delete/

rename)

• Supports electronic program guide (EPG)

• Supports HDTV video/audio output

• Supports HD TV input

• Supports AV input for monitor installing

• Supports DC+12V out for monitor installing

• Ease of use via shortcut keys

• Supports RCU

• Built in loudspeaker for audio play

• Video and Audio signal when signal locked

• Built in LED light

• Large lithium battery capacity (4000mAh)

• Support 8MP camera input, supported formats are AHD

TVI CVI CVBS

1.2 Accessories

1x Manual

1x Power Adapter

1x Power Cable

1x Car Adaptor

1x Connector F-Type

1x Connector F-Type to IEC typ

1x Connector BNC to AV

2x AV Cable

1x Remote Control Unit (RCU)

1x Carry Bag

1. Antistatic: The battery is equipped with a protective circuit to avoid the occurrence of various accidents. Do not

use the battery in the generation of static electricity as static electricity (100V or above) will easily damage the

protection circuit which may lead to battery failure or damage, heat causing smoke/re or deformation of the battery

pack.

2. Charge temperature range: Recommended charge temperature range is 0~45. Charging in an environment beyond

this range may cause a decrease in battery performance and reduce the life span.

3. Charging mode: Please use the supplied charger in the recommended environment for the battery charge. After

discharge of the battery, please charge the battery in time. Due to the special characteristics of the car charging, the

battery cannot reach the saturation state when the vehicle is used to charge the battery.

4. First use: With the rst use of the battery, if the battery is not clean or an abnormal smell or other abnormal behavior

is noted, please discontinue charging and return to Matchmaster Communications Pty Ltd.

5. When the meter is not in use for a long period of time it is best to remove the battery from the device and place in a

low temperature and humidity environment for optimal preservation.

6. Battery period of guarantee: The warranty period is 6 months from the date of shipment. However, if the problem is

not due to the failure of the manufacturing process, but instead due to improper use or storage warranty will not be

applied.

NOTE

1 OVERVIEW

For technical support call 1800 237 425 or visit www.matchmaster.com.au | Page 3 of 16

Instruction Manual

12MM-DSTM2

2.1 Remote Control

1. Power

2. Show the teletext content if teletext is transmitted

3. Subtitle language

4. Sleep

5. Find

6. Play, stop and pause

7. Main menu

8. Conrm the highlighted menu item. Open the channel list

9. Left and right

10. EPG

11. Fast backward and fast forward

12. Numeric key (0-9)

13. Favorite channel

14. Mute

15. Multi-coloured buttons

16. Zoom

17. PVR

18. GOTO TP or Satellite

19. Recall

20. Start recording

21. Exit

22. Up and down

23. Display information

24. TV/radio

25. Play previous item and play next item

26. Satellite list

27. Audio language

141

2 INTRODUCTION OF PANEL FUNCTIONS

2.2 Front Panel Introduction

1. Power switch: press it for 3~4 seconds to switch the

device power on/off

2. Power indicator

3. Battery indicator (Red light for charging, green light for

fully charged)

4. 13V indicator

5. 18V indicator

6. 22KHz indicator

7. Signal Locked indicator

8. F1~F4: shortcut keys

9. Numeric keys

10. GOTO: Select satellite or transponder

11. LIGHT: Long press 3~4seconds to turn on LED oodlight

12. SCREEN: Signal source switching

13. MUTE: turn on or turn off the voice

14. SPEC: shortcut key for spectrum analyzer

15. CONS: shortcut key for constellation analyzer

16. FIND: shortcut key for satellite nding

17. ANGLE: Shortcut key for Angle calculation

18. Arrow keys: The keys offer the movement of cursor to a

specied direction.

19. OK: conrm key

20. MENU: Show main menu

21. EXIT: exit menu (main menu or sub menu)

22. Digitron: Show the current signal quality

23. LCD screen

2 73 4 5 6

911 20 2118

For technical support call 1800 237 425 or visit www.matchmaster.com.au | Page 4 of 16

Instruction Manual

12MM-DSTM2

2.4 Rear Panel Introduction

1. LED oodlight

2. Holder

3. Loudspeaker

4. Battery

5. Hand grips

2.3 Top Panel Introduction

1. F connector male for Satellite Input

2. F connector male for Terrestrial and Cable Input

3. USB connector

4. HDTV OUT connector

5. AV OUT connector (3.5 Phone Jack)

6. AV IN connector (3.5 Phone Jack)

7. Reset key

8. DC jack (for charger)

9. HD IN connector

1 2 3 4 5 6 7 8

2 3

When you turn on the device, you can see the main menu

which consists of DVB-S2, DVB-T2, DVB-C, Compass,

Spectrum, Multimedia and Setting.

3 DETAILED OPERATION GUIDE

3.1 DVB-S/S2

3.1.1 Satellite Finding

Move cursor to “Satellite Finding” and press “OK’’, then you

will enter the “Satellite Finding’’ interface.

For technical support call 1800 237 425 or visit www.matchmaster.com.au | Page 5 of 16

Instruction Manual

12MM-DSTM2

2. Press“OK’’ on the LNB Type option, then you will see

the following window. Press [ / ] to select the LNB

Type and press “OK’’ to confirm.

1. Press“OK’’ on the Satellite option, then you will see the

following window. Press [ / ] to select an existing

satellite and press “OK” to confirm.

3. Press“OK’’ on the Freq, Symbol Rate, Polarity option,

and follow steps as above to adjust as needed.

4. Use the number buttons to input the Frequency,

Symbol Rate and Polarity manually, then press “OK’’ to

confirm.

5. When the signal is locked, the buzzer will sound. The

signal quality bar will also be displayed on the LCD.

Meanwhile, the LOCK LED will light up.

6. Press“OK ’’on the Search option, and the satellite finder

will begin to search the channel according to the TP

you selected or input manually. It will switch to the

Program page after the search (if there is a program on

the Transponder).

For technical support call 1800 237 425 or visit www.matchmaster.com.au | Page 6 of 16

Instruction Manual

12MM-DSTM2

3.1.2 Dish Setting

Move cursor to “Dish Setup’’ and press “OK’’, then you can

enter the “Dish Setup’’ interface.

1. Under the Satellite list page, you can press [ / ] to

select the satellite.

2. Press [F1] to add a new satellite through setting

Satellite Name, Longitude Direction, Longitude Angle

or Band.

3. Press [F2] to edit existing satellite, which includes

Satellite Name, Longitude Direction, Longitude Angle

and Band.

4. Press [F3] to delete existed satellite. If you press OK,

the satellite will be deleted or you can press “EXIT’’ to

exit.

For technical support call 1800 237 425 or visit www.matchmaster.com.au | Page 7 of 16

Instruction Manual

12MM-DSTM2

6. Press [GOTO] to get into the TP list, you can also use

[F1] [F2] [F3] [F4] to add, edit, delete or begin to scan

the selected TP. Press [GOTO] to return to the satellite

list.

5. Press [F4] to begin scan, with Default, Blind Scan and

Network optional scan modes.

7. Select one of the satellites and press [ / ] to get

into the LNB Type setting.

8. LNB Type: Press [ / ] to choose LNB Type between

9750/10600, 9750/10750, 05150, 05750, 09750,

10600, 10700, 10750, 11300 and 11475.

9. LNB Power: Press [ / ] to choose between Off/13V/

(13V/18V)/18V.

10. 22K: Choose AUTO/ON/OFF.

11. Toneburst: Press [ / ] to choose between None/

BurstA/BurstB.

12. DiSEqC1.0: Press [ / ] to choose between None/

LNB1/ LNB2/ LNB3/ LNB4.

13. DiSEqC1.1: Press [ / ] to choose between None/

LNB1~LNB16.

14. Motor: Press [ / ] to choose between None/

DiSEqC1.2/DiSEqC1.3.

For technical support call 1800 237 425 or visit www.matchmaster.com.au | Page 8 of 16

Instruction Manual

12MM-DSTM2

3.1.3 Angle Calculation

Move cursor to “Angle Calculation” and press “OK’’, then

you can enter the “Angle Calculation’’ interface.

1. Press [ / ] on Satellite option to select an existing

satellite, the longitude of the satellite will be changed

correspondingly.

2. Press [ / ] on Sat Longitude option, then you can

use the number keys to input the satellite longitude you

want.

3. If you select Manual, then you can move cursor to the

Local Longitude and the Local Latitude and use the

Number keys to input the value you want. (Press [ /

]to select east or west local longitude, south or north

Hemisphere).

4. When a parameter has changed, the system will

calculate the result and will show the picture on the

screen automatically.

3.1.4 Constellation Analyzer

Move the cursor to “Constellation Analyzer” and press

“OK’’, then you will enter the “Constellation Analyzer”

interface.

1. Press [ / ] to select a satellite and you can see the

Transponder changes accordingly.

2. Press [ / ] to select a Transponder and you can

see TP frequency, Symbol Rate and Polarity change

accordingly.

3. Press“OK ’’, then you will see the quality bar and the

strength bar.

4. Under Constellation Analyzer interface (by Frequency),

press

[ / ] to switch between other Frequency of the

selected satellite

For technical support call 1800 237 425 or visit www.matchmaster.com.au | Page 9 of 16

Instruction Manual

12MM-DSTM2

3.2 DVB-T/T2

Move cursor to “DVB-T” and press “OK’’, then you will enter

the “DVB-T/T2” interface.

1. Press [ / ] on Manual Search and press“OK’’ , then

you will see the following menu.

3.3 DVB-C

Move cursor to “DVB-C” and press “OK”, then you will

enter the “DVB-C” interface.

1. Press [ / ] on Manual Search and press“OK’’ , then

you will see the following menu.

For technical support call 1800 237 425 or visit www.matchmaster.com.au | Page 10 of 16

Instruction Manual

12MM-DSTM2

3.4 Compass

Move cursor to “Compass” and press “OK” then you will

enter the “Compass” interface.

1. Before using this function, please calibrate the

equipment. By pressing [F1 key] and horizontally

rotating to calibrate the equipment.

2. Press [ / ] to can choose the satellite and it

will calculate the Elevation and Azimuth value

automatically.

3. The red arrow represents the north needle, and the

blue arrow represents the south needle

4. Note: to use this function, you need to set the local

latitude and longitude parameters first. The calculated

value is for reference only.

3.5 Spectrum

Move cursor to “Spectrum” and press “OK”, then you will

enter the “Parameter Setting” interface.

1. Press [F1] to switch SPAN of spectrum frequency, FULL

is default. The smaller span will show clearer signal

status of frequencies.

2. Press [F4] to pause current status.

3. Press [ / ] to move power reference position.

4. Press [ / ] to move cursor to select the frequency,

the signal strength of the selected frequency will be

displayed on the left-top corner.

5. DVB-S/DVB-T/DVB-C all support spectrum sub-board

function

3.6 Multimedia

Connect your USB and move the cursor to “Multimedia”

and press “OK”, then you will enter the “USB” interface.

1. Press [ / ] on Multimedia and press “OK”, then you

will see the following menu.

Indice

Altri manuali Matchmaster Strumento di misura

Matchmaster

Matchmaster 12MM-DSTM1 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente