Mega System Tech iCAMView iCV-01a Manuale utente
iCAMView
User Manual
Version 2.2
For models:
iCV-01a / iCV-01b / iCV-02 / iCV-03
Copyright Information
Copyright © 2004, Mega System Technologies, Inc.
All rights reserved.
Reproduction without permission is prohibited.
Technical Support and Contact Information
Mega System Technologies, Inc.
Tel: +886-2-87922060
Fax: +886-2-87922066
Web: www.megatec.com.tw
iCAMView Web: www.icamview.com
i
CONTENTS
Chapter 1: Introduction ________________________________________1
Section 1. Features___________________________________________1
Section 2. iCAMView as a Remote Surveillance System ______________1
Section 3. Package Contents ___________________________________2
Chapter 2: Installation Procedure ________________________________4
Chapter 3: iCAMView, USB Camera and the Network ________________5
Section 1. Installation Procedure_________________________________5
Chapter 4: Using iCAMView Utility toSetupIP & Update Firmware_________7
Section 1. Installing iCAMView Utility _____________________________7
Section 2. Using iCAMView Utility________________________________8
2.1 Setup Wizard_____________________________________________9
2.2 Launch iCAMView________________________________________13
2.3 IP Configuration__________________________________________14
2.3.1 IP Address ____________________________________________14
2.3.2 Advanced _____________________________________________15
2.4 Upgrade Firmware________________________________________17
2.5 About__________________________________________________19
2.6 Refresh ________________________________________________19
Chapter 5: iCAMView Web Manager _____________________________20
Section 1. Introduction________________________________________20
Section 2. iCAMView Web Manager Interface______________________20
2.1 Web-Camera Selection ____________________________________22
2.2 Information _____________________________________________23
2.2.1 System Status _________________________________________23
2.2.2 Current Connections ____________________________________24
2.2.3 Event Log_____________________________________________25
2.3 Basic Settings ___________________________________________25
2.3.1 Camera Settings________________________________________25
2.3.2 Network ______________________________________________26
2.3.3 Account Settings________________________________________29
2.4 Advanced Settings________________________________________31
2.4.1 Event Notification _______________________________________31
2.4.2 Motion Detection _______________________________________35
2.4.3 Image Recording _______________________________________38
ii
2.4.4 E-mail / FTP ___________________________________________39
2.4.5 System Settings ________________________________________42
2.4.6 Image Server __________________________________________45
2.4.7 Language _____________________________________________46
2.4.8 About ________________________________________________47
2.5 Viewing images using PDA / Web enabled mobile phone__________48
Chapter 6: iMultiView _________________________________________50
Section 1. Installing iMultiView _________________________________50
Section 2. Using iMultiView____________________________________50
2.1 Device _________________________________________________51
2.2 View___________________________________________________60
2.3 System ________________________________________________60
2.4 User___________________________________________________61
2.5 Help___________________________________________________62
2.6 Drag-and-Drop Feature____________________________________62
Appendix A: Router Configuration ______________________________64
Appendix B: Methods to Update iCAMView Firmware_______________82
Appendix C: IP Address, Subnet and Gateway ____________________83
Appendix D: Glossary ________________________________________85
iCAMView user manual -1-
Chapter 1: Introduction
Chapter 1: Introduction
Section 1. Features
iCAMView is a compact stand-alone web-server capable of remote video
surveillance. It can be accessed from anywhere in the world via a standard browser
by entering the IP, account and password. Each system can simultaneously support
any two combinations of USB PC cameras be it regular, infrared or pan-tilt. With its
built-in web-server, iCAMView can stream video images directly to the Internet without
have to go through a computer. iCAMView features a Windows-based software that
allows the user to archive streaming video directly into the hard-drive. The same
software also allows the user to monitor multiple cameras on one screen.
Features:
•Built-in Web Server
•10/100Mbps Fast Ethernet Network Access
•Support Any Java-Enabled Web Browser
•LCD display shows the IP address, Subnet Mask and Gateway
•32-Bit RISC CPU
•1MB Flash Memory
•8MB Dynamic Memory
•Support Up to 30 Remote Viewers for each camera
•Allow Up to 8 User Accounts and Passwords
•5.3VDC 1A Maximum
•Operating Temperature: 0°C ~ 60°C
•Operating Humidity: 10% ~ 90%
•Dimensions: 48mm x 63mm x 21m
•Weight: 75g
•For Indoor Use. Protective housing required for use
•Network Protocol: HTTP, TCP/IP, UDP, SMTP, PPPoE, Dynamic DNS, DNS
Client, SNTP, BOOTP, DHCP, FTP, SNMP
•Support All USB PC Camera with VIMICRO ZC0301 Plus processor built-in
•Resolution: 640 x 480, 320 x 240, 160 x 120.
•Frame Rate: Up to 20fps in 320 x 240
•Motion JPEG streaming video
•2 USB Ports for PC Cameras
•USB 1.1 & 2.0 compliant
•Can combine with two different PC cameras
•Support Pan/Tilt and Infrared USB PC Camera
Section 2. iCAMView as a Remote Surveillance System
Once iCAMView is installed, the user can check any of the connected PC cameras
using a standard web browser. The user can monitor and control these cameras
simply by entering the IP address of the iCAMView into a Web Browser from
anywhere in the world. For instance, the user can be in Australia but is able to
iCAMView user manual -2-
Chapter 1: Introduction
monitor his factory production in China, and if he likes, check on his branch office
located in Singapore, all simultaneously.
Fig.1. iCAMView Network Diagram
Section 3. Package Contents
Your iCAMView package should contain the following items;
1. iCAMView,
2. Quick Installation Guide
3. iCAMView Utility CD, which contains;
a. iCAMView Utility: to configure IP address, update the firmware, etc.
b. iMultiView: Windows platform to monitor multiple iCAMView.
c. Time Server: Time adjustment utility.
d. Adobe Acrobat 5.0 Reader.
e. iCAMView user manual, and
f. Camera Windows Driver
4. 5.3V DC Adapter
5. USB Camera
iCAMView user manual -3-
Chapter 1: Introduction
Fig.2. iCAMView Front View
Fig.3. iCAMView Back View
LED Status Indicators on iCAMView
Light color Signal definition Condition description
Green Power state On: Normal power
Red Error Condition On: Error condition occurred
Orange Logon state On: When there is user logon and
receive the image.
Yellow USB data activity Flash when there is data
transmit/receive on the USB.
Fig.4. iCAMView Status LED Indicator
Light indicators on iCAMView LAN Port LED
Light color Condition description
Green On: Internet correspond speed is 100M
Flash: Data transmitting/receiving
Yellow On: Internet correspond speed is 10M
Flash: Data transmitting/receiving
Fig.5. iCAMView LAN LED Indicators
iCAMView user manual -4-
Chapter 2: Installation Procedure
Chapter 2: Installation Procedure
Before you start using iCAMView, you will need to set-up both the hardware and
software. The following is a flow chart on the installation procedure:
Fig.6. iCAMView installation flowchart
Connect iCAMView,
USB Camera and the Network cable
(Chapter 3)
Connect Network cable to ROUTER
/ HUB / xDSL modem
Install iCAMView Utility (Chapter 4)
and iMultiView (Chapter 6)
Use Internet Explorer (>5.0) to
access iCAMView Web Manager
(Chapter 5).
iCAMView set-up completed
1
2
3
4
5
iCAMView user manual -5-
Chapter 3: iCAMView, USB Camera and the Network
Chapter 3: iCAMView, USB Camera and the Network
The following details the installation procedure for iCAMView.
Section 1. Installation Procedure
Step 1:
Connect the PC camera
into the USB port of
iCAMView.
Step 2:
Connect the iCAMView
to LAN by using the
Ethernet UTP port.
Step 3:
Connect DC power
adapter output into
iCAMView socket, and
plug the DC power input
into the wall socket
iCAMView user manual -6-
Chapter 3: iCAMView, USB Camera and the Network
Step 4:
The LCD will display the
IP, Subnet Mask and
Gateway IP. Use a WEB
browser to login into the
iCAMView IP address.
The icon on the
LCD shows that a USB
camera is connected.
The LCD display shows
that two USB cameras
are attached to the
iCAMView.
Warning:
Please make sure the input Voltage and Frequency of the DC power adapter (DC
5.3V) is correct before plugging into the power outlet!
iCAMView user manual -7-
Chapter 4: Using iCAMView Utility to Setup IP & Update Firmware
Chapter 4: Using iCAMView Utility to Setup IP & Update
Firmware
Section 1. Installing iCAMView Utility
1. Insert the enclosed iCAMView CD into the CD-ROM drive. iCAMView setup will
auto run. The following menu will show up. Click on the buttons on the left to
install the programs you want.
"iCAMView Utility - This is a program that helps the user perform quick
installation. It will detect the current configuration and take the user through
the necessary network setup.
a. Click the ‘iCAMView Utility’ button to commence installation.
b. After the step by step installation is completed, the iCAMView Utility
group will appear in Windows ’Start’ ÆiCAMView Utility ‘Program
Group’. Click this to start the program.
Fig.7. iCAMView Utility Group
"iMultiView - This is a windows based program designed to allow user to
control a large number of iCAMView websites located either in a LAN or on a
WAN.
"Read User’s Manual - Click to read iCAMView's User Manual. You will
need Adobe Acrobat Reader v5.0 or higher.
"Adobe Acrobat Reader v5.0 - This will install Acrobat Reader v5.0 on your
local hard drive.
"Sun Jave / ActiveX - Install Sun Java for viewing the video image by Java, or
install the OCX for viewing by ActiveX.
Questo manuale è adatto per i seguenti modelli
3
Indice
