Metermatic EM6 Foglio di istruzioni

EM6 Electronic

Calculator

Configuration Manual

EM6-SVH01-0101-01-E

EM6-SVH01-0101-02-E

EM6-SVH01-0101-03-E

 EM6 Configuration Manual 
 
 
Page | 2 Revision 5.0 
Author: R.Tandy May 18 
 
Table of Contents 
 
Glossary------------------------------------------------------------------------------------- 8 
How to use this manual ------------------------------------------------------------------- 9 
Metrological Parameters-----------------------------------------------------------------10 
Navigating through the setup menu----------------------------------------------------11 
How to use an error table----------------------------------------------------------------12 
Tables---------------------------------------------------------------------------------------13 
1. Table 1: System Data-Error -------------------------------------------------------13 
2. Table 2: Product-Controller Data-Error -----------------------------------------13 
3. Table 3: Ticket / Product Controller Errors-------------------------------------13 
4. Table 4: Load Errors ---------------------------------------------------------------16 
5. Table 5: Valve Outputs for different vehicle configurations-----------------17 
6. Table 6: Valve Outputs for depot configuration -------------------------------18 
7. Table 6: Inputs ----------------------------------------------------------------------18 
8. Table 7: Temperature errors-------------------------------------------------------19 
Figures--------------------------------------------------------------------------------------20 
NOTE: REFER TO ‘ ------------------------------------------------------------------------20 
1. Figure 1: Pump Mode--------------------------------------------------------------21 
2. Figure 2: Gravity Mode------------------------------------------------------------21 
3. Figure 3: ‘Pump & Gravity’ (2-Valve Operation) -----------------------------21 
4. Figure 4: ‘Pump & Gravity’ (3-Valve Operation) -----------------------------22 
5. Figure 5: Two stage and Digital control valve ---------------------------------22 
Error codes and description -------------------------------------------------------------24 
1. Power Failure Error (1) ------------------------------------------------------------24 
2. Reset Error (2) ----------------------------------------------------------------------24 
3. Pulsar Count (8)---------------------------------------------------------------------24 
4. No Flow (16) ------------------------------------------------------------------------24 
5. Minimum Flow (32)----------------------------------------------------------------24 
6. Meter Direction (64) ---------------------------------------------------------------26 
7. Stop button (128) -------------------------------------------------------------------26 
8. Communication Error (256)-------------------------------------------------------26 
9. Temperature Error (512)-----------------------------------------------------------26 
10. Density Error (2048) ---------------------------------------------------------------26 
11. Meter Creep (4096)-----------------------------------------------------------------26 
12. Pump / Gravity Error (8192)------------------------------------------------------28 
13. Permissive Error (16384)----------------------------------------------------------28 
14. Data Retention Error (32768)-----------------------------------------------------28 
15. Setup Error (65536) ----------------------------------------------------------------28 
16. Ticket Corruption Error (524288)------------------------------------------------29 
17. Reset to factory defaults (1048576)----------------------------------------------29 
18. Uncompensated Totalizer has been manually changed (2097152)----------29 
19. Compensated Totalizer has been manually changed (4194304)-------------29 
20. Eprom write error (16777216)----------------------------------------------------29 
21. Deadman switch error (33554432)-----------------------------------------------29 
22. Ticket in progress (67108864)----------------------------------------------------29 
Using the Editor---------------------------------------------------------------------------30 
System Directory ----------------------------------------------------------------------31 

 EM6 Configuration Manual 
 
 
Page | 3 Revision 5.0 
Author: R.Tandy May 18 
 
1. General Purpose Directory --------------------------------------------------------31 
1.1 Input Timeout -----------------------------------------------------------------31 
1.2 Inactivity Timeout------------------------------------------------------------31 
1.3 Manager PIN ------------------------------------------------------------------31 
1.4 Technical PIN-----------------------------------------------------------------32 
1.5 Clock ---------------------------------------------------------------------------32 
1.5.1 Date-----------------------------------------------------------------------32 
1.5.2 Time ----------------------------------------------------------------------32 
2. Volume Accuracy Directory ------------------------------------------------------33 
2.1 Decimal Points----------------------------------------------------------------33 
2.2 Volume Units------------------------------------------------------------------33 
2.3 Minimum volume-------------------------------------------------------------33 
2.4 Maximum volume ------------------------------------------------------------33 
3. Preset directory----------------------------------------------------------------------34 
3.1 Compensated mode-----------------------------------------------------------34 
3.2 Preset operation---------------------------------------------------------------34 
3.3 Enter volume ------------------------------------------------------------------35 
4. Temperature and density directory-----------------------------------------------36 
4.1 Show compensated -----------------------------------------------------------36 
4.2 Print compensated ------------------------------------------------------------37 
5. Communication Directory---------------------------------------------------------39 
5.1 Data communication ---------------------------------------------------------39 
5.2 Node address ------------------------------------------------------------------39 
5.3 Depot Number-----------------------------------------------------------------39 
5.4 Vehicle Number --------------------------------------------------------------40 
5.5 Prompts-------------------------------------------------------------------------40 
5.5.1 General prompt 1 -------------------------------------------------------40 
5.5.1.1 Prompt text------------------------------------------------------------40 
5.5.1.2 Hide prompt ----------------------------------------------------------41 
5.5.1.3 Hide prompt input ---------------------------------------------------41 
5.5.2 General prompt 2 -------------------------------------------------------41 
5.5.3 General prompt 3 -------------------------------------------------------41 
5.5.4 General prompt 4 -------------------------------------------------------42 
5.5.5 General prompt 5 -------------------------------------------------------42 
5.5.6 Meter prompt 1----------------------------------------------------------42 
5.5.7 Meter prompt 2----------------------------------------------------------42 
5.5.8 Meter prompt 3----------------------------------------------------------43 
5.6 Printer Setup-------------------------------------------------------------------44 
5.6.1 Printer Type -------------------------------------------------------------44 
5.6.2 Auto Print----------------------------------------------------------------44 
5.6.3 Number of Copies ------------------------------------------------------44 
5.6.4 Line delay----------------------------------------------------------------45 
5.7 Port 1 setup --------------------------------------------------------------------45 
5.7.1 Protocol ------------------------------------------------------------------45 
5.7.2 Baud Rate----------------------------------------------------------------45 
5.7.3 Parity ---------------------------------------------------------------------46 
5.8 Port 2 setup --------------------------------------------------------------------46 
5.8.1 Protocol ------------------------------------------------------------------46 
5.8.2 Baud Rate----------------------------------------------------------------46 

 EM6 Configuration Manual 
 
 
Page | 4 Revision 5.0 
Author: R.Tandy May 18 
 
5.8.3 Parity ---------------------------------------------------------------------47 
5.9 GSM----------------------------------------------------------------------------47 
5.9.1 SMS setup ---------------------------------------------------------------47 
5.9.1.1 Profile 1- 5------------------------------------------------------------47 
5.9.1.1.1 Mobile number--------------------------------------------------47 
5.9.1.1.2 SMS printout----------------------------------------------------47 
5.9.2 Email setup --------------------------------------------------------------48 
5.9.2.1.1 Enable------------------------------------------------------------48 
5.9.2.1.2 Profile 1- 5-------------------------------------------------------48 
5.9.2.1.2.1 Email address ----------------------------------------------48 
5.9.2.1.2.2 Email printout----------------------------------------------48 
5.9.2.1.3 Outgoing server-------------------------------------------------48 
5.9.2.1.4 Sender address --------------------------------------------------49 
5.9.2.1.5 Username --------------------------------------------------------49 
5.9.2.1.6 Password---------------------------------------------------------49 
5.9.2.1.7 Outgoing port ---------------------------------------------------49 
5.9.3 Socket setup -------------------------------------------------------------50 
5.9.3.1.1 Enable------------------------------------------------------------50 
5.9.3.1.2 APN name -------------------------------------------------------50 
5.9.3.1.3 APN username--------------------------------------------------50 
5.9.3.1.4 APN password --------------------------------------------------50 
5.9.3.1.5 Server port-------------------------------------------------------51 
5.10 Driver PIN ---------------------------------------------------------------------52 
5.10.1 Enable --------------------------------------------------------------------52 
5.10.2 Driver list 1 - 5----------------------------------------------------------52 
5.10.2.1.1 Driver name 1 - 10--------------------------------------------52 
5.10.2.1.2 Driver number-------------------------------------------------52 
5.10.2.1.3 Driver name----------------------------------------------------53 
5.10.2.1.4 Driver PIN -----------------------------------------------------53 
6. Input and Output--------------------------------------------------------------------54 
6.1 Permissive 1-------------------------------------------------------------------54 
6.1.1 Enable --------------------------------------------------------------------54 
6.1.2 Description --------------------------------------------------------------54 
6.1.3 Timeout ------------------------------------------------------------------55 
6.2 Permissive 2-------------------------------------------------------------------55 
6.2.1 Enable --------------------------------------------------------------------55 
6.2.2 Description --------------------------------------------------------------55 
7. Diagnostics --------------------------------------------------------------------------56 
7.1 Clear settings, loads ----------------------------------------------------------56 
7.2 Memory Status ----------------------------------------------------------------56 
7.3 Keypad -------------------------------------------------------------------------56 
7.4 Display -------------------------------------------------------------------------56 
7.5 Can Bus ------------------------------------------------------------------------57 
7.6 Port 1 test ----------------------------------------------------------------------57 
7.7 Port 2 test ----------------------------------------------------------------------57 
7.8 Dallas tag test -----------------------------------------------------------------58 
7.9 Eprom test ---------------------------------------------------------------------58 
7.10 Inputs ---------------------------------------------------------------------------59 
7.10.1 Inputs 1-------------------------------------------------------------------59 

 EM6 Configuration Manual 
 
 
Page | 5 Revision 5.0 
Author: R.Tandy May 18 
 
7.10.1 Inputs 2-------------------------------------------------------------------59 
7.11 GPS status ---------------------------------------------------------------------60 
7.11.1 Status ---------------------------------------------------------------------60 
7.11.2 Coordinates--------------------------------------------------------------60 
7.11.3 Time ----------------------------------------------------------------------60 
8. Read Only----------------------------------------------------------------------------61 
8.1 Version-------------------------------------------------------------------------61 
8.2 Software checksum-----------------------------------------------------------61 
8.3 W & M checksum ------------------------------------------------------------61 
8.4 W & M events-----------------------------------------------------------------61 
8.5 EM6 pin outs ------------------------------------------------------------------62 
8.6 EM6 test points ---------------------------------------------------------------62 
8.7 EM6 fuses----------------------------------------------------------------------62 
8.8 View setup---------------------------------------------------------------------62 
Meter Setup Directory ----------------------------------------------------------------63 
1. General purpose---------------------------------------------------------------------63 
1.1 Enabled-------------------------------------------------------------------------63 
1.2 Meter name --------------------------------------------------------------------63 
1.3 Error hold ----------------------------------------------------------------------64 
1.4 Pulse Trip ----------------------------------------------------------------------64 
1.5 Pulse Delay--------------------------------------------------------------------65 
2. Flow Control ------------------------------------------------------------------------66 
2.1 Valve type ---------------------------------------------------------------------66 
2.2 Meter Direction ---------------------------------------------------------------66 
2.3 Minimum Rate ----------------------------------------------------------------66 
2.4 Minimum Time ---------------------------------------------------------------67 
2.5 No Flow Time-----------------------------------------------------------------67 
2.6 Reverse volume---------------------------------------------------------------67 
2.7 Delivery mode-----------------------------------------------------------------68 
See ‘--------------------------------------------------------------------------------------------68 
2.8 Pump Control Options -------------------------------------------------------69 
2.8.1 Valve Delay -------------------------------------------------------------69 
2.8.2 Final Trip ----------------------------------------------------------------69 
2.8.3 Fast open-----------------------------------------------------------------70 
2.8.4 Fast close-----------------------------------------------------------------70 
2.9 Gravity Control Options-----------------------------------------------------70 
2.9.1 Valve Delay -------------------------------------------------------------70 
2.9.2 Final Trip ----------------------------------------------------------------70 
2.9.3 Fast Open ----------------------------------------------------------------70 
2.9.4 Fast Close----------------------------------------------------------------71 
2.10 Valve setup --------------------------------------------------------------------71 
2.10.1 Valve Delay -------------------------------------------------------------71 
2.10.2 Final Trip ----------------------------------------------------------------71 
2.10.3 Fast Open ----------------------------------------------------------------71 
2.10.4 Fast Close----------------------------------------------------------------72 
2.10.5 Slow flow----------------------------------------------------------------72 
2.10.6 Fast flow 1---------------------------------------------------------------72 
2.10.7 Fast flow 2---------------------------------------------------------------73 
2.10.8 Tolerance ----------------------------------------------------------------73 

 EM6 Configuration Manual 
 
 
Page | 6 Revision 5.0 
Author: R.Tandy May 18 
 
3. Volume Accuracy-------------------------------------------------------------------74 
3.1 Pulsar type ---------------------------------------------------------------------74 
3.2 Pulses per Volume------------------------------------------------------------74 
3.3 Pulse Error Counter ----------------------------------------------------------74 
3.4 Pump Switch Points----------------------------------------------------------74 
3.4.1 Switch Point 1-----------------------------------------------------------74 
3.4.2 Switch Point 2-----------------------------------------------------------75 
3.5 Gravity Switch Points--------------------------------------------------------75 
3.5.1 Switch Point 1-----------------------------------------------------------75 
3.5.2 Switch Point 2-----------------------------------------------------------75 
4. Temperature -------------------------------------------------------------------------76 
4.1 Temperature -------------------------------------------------------------------76 
4.1.1 Enable --------------------------------------------------------------------76 
4.1.2 Maximum----------------------------------------------------------------76 
4.1.3 Table----------------------------------------------------------------------77 
4.1.4 Offset---------------------------------------------------------------------77 
4.1.5 Expansion coefficient --------------------------------------------------77 
5. Input / Output -----------------------------------------------------------------------78 
5.1 Input ----------------------------------------------------------------------------78 
5.1.1 Input 1 (exd)-------------------------------------------------------------78 
5.1.2 Input 2 (exd)-------------------------------------------------------------78 
5.1.3 Input 3 (is) ---------------------------------------------------------------79 
5.1.4 Deadman timeouts------------------------------------------------------79 
5.1.4.1.1 Make timeout----------------------------------------------------79 
5.1.4.1.2 Break timeout ---------------------------------------------------80 
6. Products ------------------------------------------------------------------------------81 
6.1 Number of Products ----------------------------------------------------------81 
6.2 Pulse rate-----------------------------------------------------------------------81 
6.3 Product -------------------------------------------------------------------------81 
6.3.1 Select product -----------------------------------------------------------81 
6.3.2 Product Name -----------------------------------------------------------82 
6.3.3 Default density----------------------------------------------------------82 
6.3.4 Pump Calibration -------------------------------------------------------83 
6.3.4.1 Calibration Factor 1 -------------------------------------------------83 
6.3.4.2 Calibration Factor 2 -------------------------------------------------83 
6.3.4.3 Calibration Factor 3 -------------------------------------------------83 
6.3.5 Gravity Calibration-----------------------------------------------------84 
6.3.5.1 Calibration Factor 1 -------------------------------------------------84 
6.3.5.2 Calibration Factor 2 -------------------------------------------------84 
6.3.5.3 Calibration Factor 3 -------------------------------------------------84 
6.3.6 Price ----------------------------------------------------------------------85 
6.3.6.1 Enable -----------------------------------------------------------------85 
6.3.6.2 Units -------------------------------------------------------------------85 
6.3.6.3 Currency --------------------------------------------------------------85 
6.3.6.4 Modify price----------------------------------------------------------86 
6.3.6.5 Price--------------------------------------------------------------------86 
6.3.6.6 Incl/excl tax-----------------------------------------------------------86 
6.3.6.7 Tax ---------------------------------------------------------------------86 
7. Diagnostics --------------------------------------------------------------------------87 

 EM6 Configuration Manual 
 
 
Page | 7 Revision 5.0 
Author: R.Tandy May 18 
 
7.1 Clear parameters, tickets-----------------------------------------------------87 
7.2 Clear tickets -------------------------------------------------------------------87 
7.3 Totalizers ----------------------------------------------------------------------87 
7.3.1 Uncompensated---------------------------------------------------------87 
7.3.2 Compensated------------------------------------------------------------87 
7.4 Data Status---------------------------------------------------------------------88 
7.5 Alarms--------------------------------------------------------------------------88 
7.6 Clear alarms -------------------------------------------------------------------88 
7.7 Temperature -------------------------------------------------------------------88 
7.8 Input ----------------------------------------------------------------------------89 
7.9 Output --------------------------------------------------------------------------89 
7.9.1 Output 1------------------------------------------------------------------89 
7.9.2 Output 2------------------------------------------------------------------89 
7.9.3 Output 3------------------------------------------------------------------89 
7.9.4 Output 4------------------------------------------------------------------90 
8. Read Only----------------------------------------------------------------------------91 
8.1 View Tickets ------------------------------------------------------------------91 
8.2 View setup---------------------------------------------------------------------91 
 
 

EM6 Configuration Manual

Page | 8 Revision 5.0

Author: R.Tandy May 18

1. Glossary

Uncompensated Volume: Gross volume

Compensated Volume: Gross volume at standard temperature

Human Interface Controller: The controller that monitors and controls the

product controllers as well as interface to the

operator via the keypad and display. The load

information is also stored in the human-

interface-controller.

Load A load consists of a load header (which is stored

in the human-interface-controller) and one or

more tickets gathered from the product

controllers.

Load header: The information stored for a particular load i.e.

date, time, Driver number etcetera

Load View Screen The screen that displays the load. This screen is

displayed when the print button is pressed and

the human-interface-controller is in idle state.

Manager Mode: When the operator is in the configuration menu,

the system is in Manager Mode

Product Controller: The controller that controls the flow of each

individual product or arm.

Ticket: A ticket is the information stored for a particular

transaction. This information is stored on the

relevant product-controller.

EM6 Configuration Manual

Page | 9 Revision 5.0

Author: R.Tandy May 18

2. How to use this Manual

Each field that is described in this manual has three mandatory descriptions:

a) Access: Level-w

b) Hidden: Reason for the menu item to be hidden

c) Default: x units

d) Range: yyy –zzz / Options: yyy

a) Access is the level of access required to edit the field.

There are two levels of access:

1) Level-1 requires that the menu was entered via the Manager-PIN or

Technical-PIN

2) Level-2 requires that the menu was entered via the Technical-PIN and

the CF-button must also be pressed. When this happens, ‘Edit’ will

appear in the bottom right screen of the menu. In order to press the

CF-button, the seal must be broken. See ‘Metrological Parameters’.

If the user enters the menu via a level-1 access code, all the level 2 fields and

Menu items will be hidden.

b) If the menu does not appear, the ‘Hidden’ description describes the parameter

that causes the menu to be hidden.

c) Default is the default value that is set when the parameters are reset. The units

are also displayed here (where applicable).

d) Range is the data range that is allowed for this field (where applicable).

If the field is numeric, the range will be numeric

If the field is an option, the range will indicate the options available.

If the field is alphanumeric, the range will be the number of characters that is

allowed for the field.

In addition to the fields, some menu items also have the ‘Access’ and ‘Hidden’

attribute.

EM6 Configuration Manual

Page | 10 Revision 5.0

Author: R.Tandy May 18

3. Metrological Parameters

The metrological parameters are altered via the menu using access level-2 (see

‘How to use this Manual’). To change these parameters, the seal must be broken

and the CF-button must be pressed. The menu state will change from view to

edit.

The menu state can be viewed in the bottom right corner of the display.

The CF-switch is located in the top left corner of the front panel of the calculator,

above the LCD displays. See arrow below for location.

Altri manuali per EM6

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Metermatic Strumento di misura

Metermatic

Metermatic EM6 Manuale utente

Metermatic

Metermatic EM6 Foglio di istruzioni

Metermatic

Metermatic SCS-400 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente